《SAE-AS-1130F-2002-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-1130F-2002-R2007.pdf（35页珍藏版）》请在三一文库上搜索。
1、AEROSPACE STANDARD AS1130 REV. F Issued1970-11 Revised2002-02 Superseding AS1130E Air and Air/Surface (Platform) Cargo Pallets 1.SCOPE: This SAE Aerospace Standard (AS) establishes three classes of pallets: a.Type A, Air only Pallet b.Type B, Platform Pallet (Air/Surface Intermodal) c.Type C, Adapte
2、r Pallet Pallets will have nominal dimension of: a.Size F pallet (10 ft) (NAS 3610-2F1P) - 2.44 m x 2.99 m (96 in x 117.75 in) b.Size R pallet (16 ft) (NAS 3610-2R1P) - 2.44 m x 4.98 m (96 in x 196 in) c.Size G pallet (20 ft) (NAS 3610-2G1P) - 2.44 m x 6.06 m (96 in x 238.5 in) d.Size H pallet (30 f
3、t) (NAS 3610-2H1P) - 2.44 m x 9.12 m (96 in x 359.25 in) e.Size J pallet (40 ft) (NAS 3610-2J1P) - 2.44 m x 12.19 m (96 in x 480 in) Type A, Air only pallets, will normally be on aircraft equivalent roller conveying systems and/or on similarly equipped ancillary ground handling devices. Type B, Plat
4、form pallets, are suitable for air/surface handling and transport systems. Supplementary requirements for Type B version are found in Section 4. Type C, Adapter pallets, are used to adapt 2.44 m x 2.44 m (8 ft x 8 ft) surface mode only containers for transport. Supplementary requirements for Type C
5、version are found in Section 5. NOTE: Use of the adapter pallet with surface mode only 2.44 m x 2.44 m (8 ft x 8 ft) containers may require uniform load distribution on the base cross members of these containers for carriage on certain aircraft. The aircraft approved Weight and Balance Manual should
6、 be referred to for loadability procedures or limitations, or both. SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for a
7、ny particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2007 SA
8、E International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 87
9、7-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Reaffirmed 2007-12 Copyright SAE International Provided by IHS under license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resal
10、e, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 2 - 1.1Purpose: This Aerospace Standard (AS) provides dimensional, structural, and environmental requirements for 2.44 m (8 ft) wide pallets to be used in freighter versions of ce
11、rtificated aircraft equipped to provide restraint to pallets tested to the requirements of NAS 3610 Class II restraint system. It is also intended to be compatible with 2.44 m x 2.44 m (8 ft x 8 ft) cross section containers described in AS832. The Type C adapter pallet is intended to be compatible w
12、ith 2.44 m x 2.44 m (8 ft x 8 ft) cross section containers described in ANSI MH 5.1, Cargo Containers and ISO 1496 Series 1, Freight Containers. Pallet nets used in conjunction with these pallets are described in AS1131. The minimum essential criteria are identified by use of the key word “shall“. R
13、ecommended criteria are identified by use of the key word “should“, and while not mandatory, are considered to be of primary importance in providing serviceable, economical, and practical air transport pallets. Deviation from recommended criteria should occur only after careful consideration, extens
14、ive testing, and thorough service evaluation have shown alternate methods to be satisfactory. 2.REFERENCES: 2.1Applicable Documents: The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other
15、 publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spe
16、cific exemption has been obtained. 2.1.1SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. AS832Air and Air/Surface (Intermodal) General Purpose Containers AS1131Air and Air/Surface (Platform) Cargo Pallet Nets 2.1.2ISO Publications: Available from International
17、 Organization for Standardization, Case Postale 56, CH-1211, Geneve 20, Switzerland. ISO 4115Air Cargo Equipment - Air/Land Nets ISO 4116Air Cargo Equipment - Ground Equipment Requirements for Compatibility With Unit Load Devices ISO 4117Air and Air/Land Cargo Pallets - Specification and Testing ISO
18、 1496/1Series 1 Freight Containers - Specification and Testing - Part 1: General Cargo Containers Copyright SAE International Provided by IHS under license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted witho
19、ut license from IHS -,-,- SAE AS1130 Revision F - 3 - 2.1.3FAR Publications: Available from Federal Aviation Administration, 800 Independence Avenue, SW, Washington, DC 20591. Federal Aviation Regulation (FAR) Part 25, United States Department of Transportation Technical Standard Order TSO-C90 2.1.4
20、NAS Standards: Available from Aerospace Industries Association, 1250 Eye Street, NW, Washington, DC 20005. NAS 3610Cargo Unit Load Devices, Specification for 2.1.5U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-
21、5094. MS33601ATrack and Stud Fitting for Cargo Transport Aircraft, Standard Dimensions for Available from Specification Sales, Building 197, Washington Navy Yard, General Service Administration, Washington, DC 20407. United States Federal Test Method Standard 406, Plastics - Methods of Testing 2.1.6
22、IATA Publications: Available from International Air Transport Association, 800 Place Victoria, P.O. Box 113, Montreal, Quebec, Canada H4Z 1M1. IATA 50/916 ft or 20 Ft Pallet for NAS 3610 Class II Restraint System 2.1.7ANSI Publications: Available from American National Standards Institute, 11 West 4
23、2nd Street, New York, NY 10036-8002. ANSI MH5.1Basic Requirements for Cargo Containers Copyright SAE International Provided by IHS under license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license
24、from IHS -,-,- SAE AS1130 Revision F - 4 - 3.BASIC REQUIREMENTS: 3.1External dimensions and pallets shall be as specified in Table 1 and Figure 1. Diagonal tolerances shall be as specified in Table 2. 3.2Construction: 3.2.1Pallet construction shall be rugged, weatherproof, minimizing maintenance and
25、 original cost by having no moving parts. 3.2.2All fittings and appurtenances shall be within the maximum outside dimensions of the pallet. 3.2.2.1Mating devices that support, transfer position and secure pallets shall be provided by transportation carriers, transferring equipment or terminal facili
26、ties. 3.2.3Pallet construction shall have sufficient structural strength to perform its intended function and to meet the structural design and test requirements of this document. 3.3Pallet Surfaces: 3.3.1The top and bottom surfaces of the pallet shall be parallel, flat, and continuous. 3.3.1.1For t
27、he length of the pallet the bottom surface shall have a smooth to a flat plane within 1.6 mm (0.0625 in). This shall allow for a waviness factor of crest to crest at a pitch of 914 mm (36 in) minimum. 3.3.2No structure shall protrude below the lower surface. 3.3.3Construction: 3.3.3.1The pallet edge
28、s (Length “L“) shall have a nominal thickness of 50.8 mm (2 in) from the lower surface. This thickness may be varied when the design employed results in a lighter and more durable structure capable of accepting uniform loading of 1953 kg/m2 (400 lb/ft2) when supported on conveying system per 3.3.3.3
29、. Copyright SAE International Provided by IHS under license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 5 - TABLE 1 - Pallet Dimensions /1/ Copyright
30、SAE International Provided by IHS under license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 6 - FIGURE 1 Copyright SAE International Provided by IHS u
31、nder license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 7 - 3.3.3.2The pallet shall be enclosed on all four sides by an edge member conforming to Fig
32、ures 2, 3, 4A and 4B. The vertical surface of the pallet edge between the restraint provisions shown in Figures 3, 4A, and 4B. Section A-A, Type A and B pallets, shall be smooth and continuous to provide automatically latching aircraft systems interface. a.The pallet bottom skin shall be enclosed by
33、 its edge extrusion. b.The bottom surface shall be flush with the edge member. c.The lower edge of the edge members shall be as shown in Figure 4A and 4B. d.The pallet corners shall have a 63.5 mm 12.7 mm (2.50 in 0.50 in) radius in the plane of the pallet. e.Pallet corners should be readily replace
34、able when built as a separate bolted or riveted on part. 3.3.3.3The pallet design shall provide for support and ease of movement at the rated distributed load on minimum conveyor systems as described in the following: a.Four rows of rollers approximately equally spaced over a minimum width of 1930.4
35、 mm (76 in) measured between centers with each row composed of 38 mm (1.5 in) diameter rollers 76.2 mm (3 in) long uncrowned with edge radius of 1.6 mm (0.06 in) R, spaced on 254 mm (10 in) centers. Pallet travels perpendicular to roller axis. b.Swivel casters with 25 mm (1 in) diameter wheels havin
36、g a contact length of 51 mm (2 in) located on a 305 mm x 305 mm (12 in x 12 in) grid pattern. Pallet travel is in all directions across grid. TABLE 2 - Diagonal Tolerances - Type B & C Pallets Pallet Code Overall Length in Overall Length mm S in S mm P in P mm K1 Max in K1 Max mm J48012 19247211,988
37、.8892260.63/419 H359-1/4 9 125351-1/4 8 921.7892260.65/815.9 G238-1/2 6 058230-1/4 5 848.4892260.61/212.7 R196 4 978188 4 775.2892260.67/1611.1 F117-3/4 2 991109-3/4 2 787.6892260.63/8 9.5 NOTES: For definitions of S, P, and D, see Figure 9 K1 = D1 - D2 Copyright SAE International Provided by IHS un
38、der license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 8 - FIGURE 2 - End Slots or Blocks (Both Sides) Copyright SAE International Provided by IHS un
39、der license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 9 - FIGURE 3 - Side Restraint Slots Location Copyright SAE International Provided by IHS under
40、 license with SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 10 - FIGURE 4A - Side Slot Detail Copyright SAE International Provided by IHS under license with
41、SAELicensee=MHI - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 11 - FIGURE 4B - Side Slot Detail Copyright SAE International Provided by IHS under license with SAELicensee=MH
42、I - NAGOYA related to 3944000/3944000013 Not for Resale, 01/23/2008 22:32:16 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS1130 Revision F - 12 - 3.3.3.3 (Continued): c.Ball transfer units with 25 mm (1 in) diameter balls located on a 127 mm x 127 mm (5 in x 5 in) g
43、rid pattern. Pallet travel is in all directions across grid. 3.3.3.4The pallet lower surface shall comply with the following conditions: a.Ball identation per 6.2 b.Ball casters per 6.3 c.Abrasion per 6.4 3.3.4Net attachments shall be per MS33601A as shown in Figures 1, 5A, and 5B. As an option, a c
44、ontinuous seat track per MS33601A may be incorporated in the pallet upper surface for net or strap attachments. 3.4Aircraft Restraint Provision: Restraint provision as shown in Figures 2, 3, 4A, and 4B shall be provided. 3.5Complete Assembly: 3.5.1Pallet shall be capable of traversing a 0.035 rad (2
45、) crest or valley with no permanent deformation or damage. 3.5.1.1To meet this condition pallets uniformly loaded to gross weight shall be capable of being supported at the cresting point through a roller contact of 2032 mm (80 in) minimum width with a roller of 38 mm (1.5 in) maximum diameter. 3.5.
46、2Pallet construction shall be free of any recesses or voids in which cargo (or other material) can be concealed. All pallet surfaces should be as free as possible of recesses and protuberances, where pests can hide, or where soil or other residues can accumulate. 3.5.3The pallet shall withstand with
47、out permanent deformation a forklift wheel load of 2721.5 kg (6000 lb) on each of two wheels on 762 mm (30 in) centers anywhere on the pallet while resting on a surface of sufficient strength and continuity to adequately support the pallet. 3.5.4The minimum pallet core stiffness shall be 225 kNm2/m
48、(2 x 106 lbf-in2/in) width of the core. 3.6Ratings: 3.6.1The pallet shall be designed for the following gross weights: 3.6.1.1F pallet - 2.99 m (10 ft) - 5670 kg (12 500 lb) 3.6.1.2R pallet - 4.98 m (16 ft) - 11,340 kg (25 000 lb) 3.6.1.3G pallet - 6.06 m (20 ft) - 13,608 kg (30 000 lb) Copyright SAE International Provided by IHS under license with SAELicensee=MHI - NAG