《SAE-AS-153201-THRU-AS-153500-1998-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-153201-THRU-AS-153500-1998-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS153201 THRU AS153500 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS15320
3、1 THRU AS153500 ISSUED 1998-11 REAFFIRMED 2007-06 STUD, STEPPED, DRILLED, 1.5 DIA ENGAGEMENT, .375-16 x .3125-24 PREPARED BY COMMITTEE E-25PROCUREMENT SPECIFICATION: NONE FEDERAL SUPPLY CLASS 5307 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION AN153201 THRU AN153500 RE
4、V. 5 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE AN153201 THRU AN153500 REV. 5. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFI
5、CATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUB
6、LICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIAT
7、ED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE I
8、nternational All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-6
9、06-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:46:35 MSTNo reprod
10、uction or networking permitted without license from IHS -,-,- STUD, STEPPED, DRILLED, 1.5 DIA ENGAGEMENT, .375-16 x .3125-24 AEROSPACE STANDARD AS153201 THRU AS153500 SHEET 2 OF 3 AS153201 THRU AS153500 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/591
11、3977001 Not for Resale, 12/04/2007 18:46:35 MSTNo reproduction or networking permitted without license from IHS -,-,- STUD, STEPPED, DRILLED, 1.5 DIA ENGAGEMENT, .375-16 x .3125-24 AEROSPACE STANDARD AS153201 THRU AS153500 SHEET 3 OF 3 AS153201 THRU AS153500 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:46:35 MSTNo reproduction or networking permitted without license from IHS -,-,-