《SAE-AS-31971A-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-31971A-2007.pdf（2页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) GAGE PIN FOR SOCKET CONTACT ENGAGEMENT TEST AS31971 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording,
2、or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1997-10 REAFFIRMED 2003-08 REVISED 2007-11 THIRD A
3、NGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 REV. A FEDERAL SUPPLY CLASS 4030 AS31971 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this repor
4、t is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled.
5、SAE invites your written comments and suggestions. RATIONAL REVISED TO INCLUDE OUTSTANDING COMMENTS. UPDATE ALL REFERENCED SPECIFICATIONS. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET. FIGURE 1 - DIMENSIONS AND CONFIGURATION NOTES: 1. D
6、IMENSIONS ARE IN INCHES, METRIC EQUIVALENTS IN PARENTHESIS ARE FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1.00 = 25.4 mm. 2. THESE GAGES ARE INTENDED FOR USE WITH ELECTRIC CONNECTOR SOCKET CONTACTS IN ACCORDANCE WITH SAE AS39029 AND SPECIFICATIONS REFERENCING THIS DOCUMENT. 3. THE CHANGE BAR (
7、l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. REQUIREMENTS: 1.
8、 DESIGN AND CONSTRUCTION: SEE FIGURE 1. 2. MATERIAL: GAGE PIN - TOOL STEEL OR TUNGSTEN CARBIDE HANDLE - OPTIONAL 3. FINISH: GAGE PIN - 6 TO 10 in RMS DETERMINED IN ACCORDANCE WITH ANSI B46.1 HANDLE - OPTIONAL 4. PLATING: NONE Copyright SAE International Provided by IHS under license with SAELicensee
9、=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:12:20 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) GAGE PIN FOR SOCKET CONTACT ENGAGEMENT TEST AS31971 SHEET 2 OF 2 REV. A TABLE 1 - FIGURE 1 DIMENSIONS DASH NUMBER CONTACT SIZE A MIN PIN
10、 DIA +.0001 (0.0025) -.0000 (0.0000) A MAX PIN DIA +.0000 (0.0000) -.0001 (0.0025) B FLAT .0145 (0.3683) 28X1 28Y1 28 .0155 (0.3937) .0085/.0065 (0.2159/0.1651) .0195 (0.4953) 26X1 26Y1 26 .0205 (0.5207) .0110/.0090 (0.2794/0.2286) .0245 (0.6223) 24X1 24Y1 24 .0255 (0.6477) .0130/.0110 (0.3302/0.279
11、4) .0265 (0.6731) 23X1 23Y1 23 .0275 (0.6985) .0140/.0120 (0.3556/0.3048) .0295 (0.7493) 22X1 22Y1 22 .0305 (0.7747) .0160/.0140 (0.4064/0.3556) .0390 (0.9906) 20X1 20Y1 20 .0410 (1.0414) .0250/.0200 (0.6350/0.5080) .0615 (1.5621) 16X1 16Y1 16 .0635 (1.6129) .0370/0320 (0.9398/0.8128) .0770 (1.9558)
12、 14X1 14Y1 14 .0790 (2.0066) .0440/.0390 (1.1176/0.9906) .0930 (2.3622) 12X1 12Y1 12 .0950 (2.4130) .0670/.0620 (1.7018/1.5748) .1240 (3.1496) 10X1 10Y1 10 .1260 (3.2004) .0870/.0820 (2.2098/2.0828) .1410 (3.5814) 8X1 8Y1 8 .1430 (3.6322) .0960/.0860 (2.4384/2.1844) .1770 (4.4958) 6X1 6Y1 6 .1790 (4
13、.5466) .1060/.0960 (2.6924/2.4384 .2240 (5.6896) 4X1 4Y1 4 .2260 (5.7404) .1200/.1100 (3.0480/2.7940) .2820 (7.1628) 2X1 2Y1 2 .2840 (7.2136) .1780/.1680 (4.5212/4.2672) .3560 (9.0424) 0X1 0Y1 0 .3580 (9.0932) .2520/.2420 (6.4008/6.1468) .4050 (10.2870) 2/0X1 2/0Y1 2/0 .4070 (10.3378) .3010/.2910 (7
14、.6454/7.3914) .4990 (12.6746) 4/0X1 4/0Y1 4/0 .5010 (12.7254) .3950/3850 (10.0330/9.7790) PART NUMBER: SEE EXAMPLE BELOW: Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:12:20 MSTNo reproduction or networking permitted without license from IHS -,-,-