《SAE-AS-38386-2A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-38386-2A-2003-R2007.pdf（2页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 2 AS38386/2 REV. A THIRD ANGLE PROJECTION AEROSPACE STANDARD AS38386/2 REV
3、. A ISSUED 1999-07 REVISED 2003-01 REAFFIRMED 2007-07 (R) CONNECTOR, AIR DUCT HOSE, GROUND COOLING, FEMALE CUSTODIAN: SAE G-3/G-3DPROCUREMENT SPECIFICATION: AS38386 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - FEMALE CONNECTOR RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW
4、POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE
5、A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/0
6、4/2007 19:00:11 MSTNo reproduction or networking permitted without license from IHS -,-,- CONNECTOR, AIR DUCT HOSE, GROUND COOLING, FEMALE AEROSPACE STANDARD AS38386/2 SHEET 2 OF 2 AS38386/2 REV. A REV. A (R) NOTES: 1.MATERIAL: a.BODY: .059 THICK, COLD ROLLED, COMMERCIAL QUALITY, CARBON STEEL AS SPE
7、CIFIED IN ASTM A 366. b.FLANGE: .125 THICK, HOT ROLLED, PICKLED AND OILED, COMMERCIAL QUALITY CARBON STEEL AS SPECIFIED IN ASTM A 569. 2.FINISH: CADMIUM PLATE PER QQ-P-416, TYPE I, CLASS 1. PLATE FLANGE AND OD OF BODY MINIMUM a.OPTIONAL: ZINC PLATE PER ASTM B 633 SC3 TYPE II 3.WELDING AND WELDER QUA
8、LIFICATION PER ANSI/AWSA D1.1. WELD SYMBOLS PER ANSI/AWSA 2.4. BUTT WELD DUCT JOINT - LOCATION OPTIONAL. 4.SURFACE TEXTURE: MACHINE EDGES 250 in Ra PER ASME B46.1. 5.REMOVE ALL BURRS AND BREAK SHARP EDGES. 6.DIMENSIONS AND TOLERANCING: ASME Y14.5M-1994. 7.DIMENSIONS ARE IN INCHES AND DEGREES TO MATC
9、H THE ORIGINAL U.S. AIR FORCE DRAWING. 8.TOLERANCES: TWO PLACE DECIMALS, .XX = .03 INCHES, THREE PLACE DECIMALS, .XXX = .015 INCHES, ANGLES 1 UNLESS OTHERWISE SPECIFIED. 9.RATIONAL: THIS DRAWING IS A DUPLICATE OF U.S. AIR FORCE DRAWING 64C1005 REVISION L DATED 20 JUNE 1983, PLUS THE VALUE ENGINEERIN
10、G CHANGE PROPOSALS NO. CO701-0001, -0002 AND -0003 APPROVED 09 APRIL 1987. 10.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO
11、 THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. TABLE 1 - DIMENSIONS PART NUMBERA B .030CD E DEGREES AS38386/2-01 8.000 8.920 8.125 9.906 90 AS38386/2-0216.00016.92016.12517.906120 AS38386/2-0312.00012.92012.12513.906120 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:00:11 MSTNo reproduction or networking permitted without license from IHS -,-,-