《SAE-AS-33671D-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-33671D-2007.pdf（7页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, CLASS 1 AS33671 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
2、electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1
3、997-09 REVISED 2007-08 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C2 REV. D FEDERAL SUPPLY CLASS 4030 AS33671 SHEET 1 OF 7 REV. D PROCUREMENT SPECIFICATION: AS23190 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineerin
4、g sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be re
5、affirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE REVISION NEEDED TO STANDARDIZE REQUIREMENTS AND CLARIFY DIMENSIONS FOR IMPROVED COMPETITION. FIGURE 1 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001
6、 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, CLASS 1 AS33671 SHEET 2 OF 7 REV. D FIGURE 1 (CONTINUED) Copyright SAE Internatio
7、nal Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, C
8、LASS 1 AS33671 SHEET 3 OF 7 REV. D Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL
9、COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, CLASS 1 AS33671 SHEET 4 OF 7 REV. D Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from I
10、HS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, CLASS 1 AS33671 SHEET 5 OF 7 REV. D Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo
11、reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLASTIC, TYPE I, CLASS 1 AS33671 SHEET 6 OF 7 REV. D TABLE 2 COLOR DASH NO. COLOR COLOR DASH NO. COLOR 0 1/ BLACK -1 BROWN -6 BLUE -2 RED -7
12、PURPLE -3 ORANGE -8 GRAY -4 YELLOW -9 1/ NATURAL -5 GREEN -10 2/ PINK 1/ ONLY STRAPS IN NATURAL AND BLACK COLORS SHALL BE STOCKED BY THE GOVERNMENT 2/ PINK STRAPS ARE INTENDED TO BE USED TO IDENTIFY COMPONENTS OR SYSTEMS THAT REQUIRE SPECIAL HANDLING IN AIRCRAFT APPLICATIONS, WITHIN THE ENVIROMENTAL
13、 LIMITATIONS OF THE STRAP. REQUIREMENTS: 1. MATERIAL: a. STRAP: NYLON PER ASTM D 4066 (REF. SAE AS23190), BLACK SHALL BE WEATHER RESISTANT. b. STRAP LOCK: 1. METAL TYPE PER ASTM A 266 CLASS 304 OR 316 (REF. SAE AS23190), SEE NOTE 4. 2. PLASTIC TYPE PER ASTM D 4066 (REF. SAE AS23190), SEE NOTE 4. c.
14、COLOR: 1. COLOR SHALL CONFORM TO EIA 359, EXCEPT BLACK AND NATURAL. NOTES: 1. ALL DIMENSIONS ARE IN INCHES. 2. THE EDGES OF THE STRAP SHALL BE SMOOTH AND WELL ROUNDED SO AS NOT TO CUT OR ABRADE WIRES, CABLES, OR THE USER OF THE DEVICE. 3. FOR TESTING PURPOSES OF 175 lb TENSILE STRENGTH AND GREATER,
15、STRAPS WITH AN EFFECTIVE LENGTH GREATER THAN 5 in THAT ARE NOT CAPABLE OF BEING FASTENED SECURELY AROUND A 1-1/ 2 in DIAMETER MANDREL OR WIRE BUNDLE ARE TO BE FASTENED AROUND A MANDREL OR WIRE BUNDLE OF THE MINIMUM DIAMETER THAT THE STRAPS ARE CAPABLE OF BEING FASTENED AROUND. 4. LOCKING DEVICES OF
16、ANY DESIGN ARE ACCEPTABLE PROVIDED THEY MEET PERFORMANCE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION SAE AS23190. WHEN METAL LOCKING DEVICES ARE USED, THEY MUST BE SECURELY ANCHORED AND SHALL NOT BE EXPOSED OUTSIDE OF THE HUB. 5. TYPE 1 TIEDOWN STRAPS MAY BE USED ON WIRE BUNDLES CONTAINING SOLID D
17、IELECTRIC COAXIAL CABLES PROVIDED THAT THE TENSION SETTING ON THE MS90387 INSTALLING TOOL IS NOT GREATER THAN THAT REQUIRED TO PREVENT AXIAL SLIPPAGE. 6. CONTOUR INDICATED BY PHANTOM LINES MAY VARY FROM THAT SHOWN TO SUIT INDIVIDUAL MANUFACTURERS DESIGN. SLIGHT MOLDING TAPER IS PERMITTED. Copyright
18、SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) STRAP, TIEDOWN, ELECTRICAL COMPONENTS, ADJUSTABLE, SELF- CLINCHING, PLAS
19、TIC, TYPE I, CLASS 1 AS33671 SHEET 7 OF 7 REV. D 7. IF THE MANUFACTURER ELECTS TO INCLUDE THE PART NUMBER ON THE PRODUCT, THE PART NUMBER IS TO BE PLACED NEAR OR AROUND THE MANUFACTURERS LOGO OR TRADEMARK SUCH THAT WHEN THE STRAP IS CUT OFF, AFTER IT IS APPLIED, THE PART NUMBER REMAINS INTACT. EXAMP
20、LE OF PART NUMBER: 8. UNIT PACKAGE MARKING: IN ADDITION TO THE PART NUMBER SHOWN IN NOTE 7, THE UNIT PACKAGE SHALL HAVE THE FOLLOWING TYPICAL INFORMATION MARKED ON THE PACKAGE OR CONTAINED WITHIN THE PACKAGE: 9. TOOL TENSION SETTINGS: THE TOOL TENSION SETTING RANGES SPECIFIED IN TABLE 1 ARE FOR TYPI
21、CAL WIRE BUNDLE APPLICATIONS. SETTINGS LESS OR GREATER THAN THE RANGES SPECIFIED MAY BE NECESSARY FOR SPECIAL APPLICATIONS. 10. A STANDARD INSTALLATION TOOL IS NOT AVAILABLE FOR EXTRA HEAVY-DUTY STRAPS. THE STRAP WILL BE QUALIFIED WITH THE STRAP MANUFACTURERS RECOMMENDED TOOL AND THE TOOL PART NUMBE
22、R USED FOR THE QUALIFICATION WILL BE LISTED WITH THE APPROVED STRAP ON THE QUALIFIED PRODUCT LIST (QPL 23190). 11. INTENDED APPLICATION: a. FOR AIRCRAFT APPLICATIONS THE LOW PROFILE STRAP IS INTENDED TO BE USED IN CONFINED SPACES, ESPECIALLY WHERE A CONVENTIONAL STRAP MAY ABRADE THE WIRE(S) AT OR AR
23、OUND THE BUNDLE BEING SECURED WITHIN THE CONFINED AREA. AS50881 PROVIDES GUIDANCE ON STRAP APPLICATION IN AIRCRAFT. b. BLACK STRAPS ARE INTENDED TO BE USED IN WEATHER RESISTANT APPLICATIONS OR IN AREAS OF DIRECT SUNLIGHT. 12. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF
24、THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:56:58 MSTNo reproduction or networking permitted without license from IHS -,-,-