《SAE-AS-39029-99-2000-R2006.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-39029-99-2000-R2006.pdf(4页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 4 AS39029/99 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS39029/99 ISSUED 2
3、000-07 CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, COAXIAL, SIZE 5 (FOR DOD-C-83527 CONNECTORS) PREPARED BY SAE SUBCOMMITTEE AE-8C1 FEDERAL SUPPLY CLASS 5935 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-39029/99A AND CONTAINS ONLY MINOR EDITORIAL AND
4、FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-39029/99A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICAT
5、ION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIO
6、NS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRAC
7、TS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. REAFFIRMED 2006-08 Copyright 2006 SAE International All rights reserved
8、. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)
9、Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:19:26 MDTNo reproduction or networki
10、ng permitted without license from IHS -,-,- CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, COAXIAL, SIZE 5 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/99 SHEET 2 OF 4 AS39029/99 THE REQUIREMENTS FOR ACQUIRING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND TH
11、E LATEST ISSUE OF MIL-C-39029. FIGURE 1. PIN CONTACTS. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:19:26 MDTNo reproduction or networking permitted without license from IHS -,-,- CONTACTS, ELECTR
12、ICAL CONNECTOR, PIN, CRIMP REMOVABLE, COAXIAL, SIZE 5 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/99 SHEET 3 OF 4 AS39029/99 FIGURE 1. PIN CONTACTS - CONTINUED. REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Mating contact: MIL-C-39029/100A. Materials: Body: Brass,
13、 half-hard or copper-beryllium. Insulator: MIL-P-19468. Crimp ferrule: Copper, annealed. Gasket: Silicone rubber. Plating: Gold as required for MIL-C-39029, type D contacts. Performance: Temperature range: -65C to +165C. Impedance: 50 ohms nominal. VSWR: 1.30:1 maximum. Frequency range: 0 to 500 MHz
14、. Insertion loss: 0.3 dB. Contact resistance: Outer contact: 1.5 milliohms maximum. Inner contact: 10.0 milliohms maximum. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:19:26 MDTNo reproduction or
15、networking permitted without license from IHS -,-,- CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, COAXIAL, SIZE 5 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/99 SHEET 4 OF 4 AS39029/99 Rated voltage: 325 V rms at sea level. Dielectric withstanding voltage: 750 V rms at sea level.
16、 Insulation resistance: 5,000 megohms minimum. Cable retention: 60 pounds minimum. Shock: Test condition D per method 2004 of MIL-STD-1344. Vibration: Test condition VI, letter J, per method 2005 of MIL-STD-1344. Directions shall be longitudinal and perpendicular. Time duration shall be 8 hours in e
17、ach direction. Installation and removal: Installation and removal of contact shall be per manufacturer recommended instructions. Shipping: Figure 1 illustrates final assembly; parts are to be shipped unassembled in a suitable container. Manufacturer recommended assembly instructions shall be shipped
18、 with each unit package. QPL evaluating activity: Defense Electronics Supply Center (DESC-E), Dayton, OH 45444. Part number: M39029/99-549. TABLE I. DESIGN CHARACTERISTICS. TABLE II. TOOLS. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:19:26 MDTNo reproduction or networking permitted without license from IHS -,-,-