《SAE-AS-4861A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-4861A-2003-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING, BUSHING, PIPE, INTERNAL AND EXTERNAL THREAD AS4861 ISSUED 1995-07 REVISED 2003-11 REAFFIRMED 2007-07 CUSTODIAN: SAE G-3/G-3B REV. A FEDERAL SUPPLY CLASS 4730 AS4861 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: /4/ AS4842 THIRD ANGLE PROJECTION SAE Technical Standards B
2、oard Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsib
3、ility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. (R) 2X 30 5 FITTING END PER AS5201 STYLE C EXCEPT AS SHOWN C HEX(A) B T THREAD INTERNAL X LOCATION OF IDENTIFI
4、CATION /5/ K FIGURE 1 FITTING, BUSHING, PIPE, INTERNAL AND EXTERNAL THREAD TABLE 1 DIMENSIONS BASIC NO. AS4861 /14/ SIZE CODE A THREAD PER AS71051 ANPT T THREAD PER AS71051 ANPT B .031 C K 01 1/4 -18 1/8 -27 .781 .615-.628 .311-.327 02 3/8 -18 1/4 -18 .781 .740-.753 .404-.423 03 3/8 -18 1/8 -27 .781
5、 .740-.753 .311-.327 04 1/2 -14 3/8 -18 1.016 .928-.941 .529-.557 05 1/2 -14 1/4 -18 1.016 .928-.941 .404-.423 06 1/2 -14 1/8 -27 1.016 .928-.941 .311-.327 07 3/4 -14 1/2 -14 1.063 1.113-1.128 .654-.688 08 3/4 -14 3/8 -18 1.063 1.113-1.128 .529-.557 09 3/4 -14 1/4 -18 1.063 1.113-1.128 .404-.423 10
6、1 -11 1/2 3/4 -14 1.250 1.363-1.380 .857-.897 11 1 -11 1/2 1/2 -14 1.250 1.363-1.380 .654-.688 12 1 -11 1/2 3/8 -18 1.250 1.363-1.380 .529-.557 13 1 1/4 -11 1/2 3/4 -14 1.281 1.738-1.755 .857-.897 INACTIVE IN PART - SEE NOTE /15/ RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-Y
7、EAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE
8、. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for R
9、esale, 12/04/2007 19:56:44 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, BUSHING, PIPE, INTERNAL AND EXTERNAL THREAD AS4861 REV. A AS4861 SHEET 2 OF 3 REV. A (R) NOTES: /1/ MATERIAL: a. DASH AS CODE LETTER TYPE 377 COPPER ALLOY FORGING PER ASTM
10、 B 124, OR HALF HARD FORGING OR BAR PER ASTM B 138, OR BAR PER AMS 4614. b. CODE LETTER D TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS-QQ-A-367 OR AMS 4133, OR TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6, OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4339. /15/ c. CODE LETTER
11、J TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5639. d. CODE LETTER K TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5648. e. CODE LETTER R TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5645. f. CODE LETTER S TYPE 34
12、7 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS 5646. /15/ g. CODE LETTER W TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS-QQ-A-367 OR AMS 4141, OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9, OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124. 2. FINISH: a. DASH AS CODE LET
13、TER CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 3 OR NONE. /16/ b. MATERIAL CODE LETTER D ANODIZE PER MIL-A-8625, TYPE II, CLASS 2 OR AMS 2472, DYE BLUE. c. MATERIAL CODE LETTER J PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. d. MATERIAL CODE LETTER K PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. e. MA
14、TERIAL CODE LETTER R PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. f. MATERIAL CODE LETTER S PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. g. MATERIAL CODE LETTER W ANODIZE PER MIL-A-8625, TYPE II, CLASS 2 OR AMS 2472, DYE BROWN SIMILAR TO COLOR 10080 OF FED-STD-595. /3/ INTENDED USE: OXYGEN SYSTEMS AND G
15、ROUND SUPPORT EQUIPMENT ONLY. PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUMBER AS CODE “A” AND SHALL BE FURNISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH AIR1176 TO A PROCESS APPROVED BY THE USER. /4/ PROCUREMENT SPECIFICATION: AS4842 EXCEPT AS SPECIFIED ON THIS STANDARD. US
16、ERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S), OR ACCREDITED DISTRIBUTOR(S), AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE OF PRODUCT. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD
17、 7A3, 15A3, OR 15B. a. FOR SIZES 03 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS“, MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION, WHEN MADE FROM FORGING. b. FOR SIZES 04 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE
18、LETTER, AND FORGING MANUFACTURERS IDENTIFICATION, WHEN MADE FROM FORGING. 6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 7. THIS STANDARD IS A FUNCTIONAL EQUIVALENT OF AN912. 8. THE CHANGE BAR ( | ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE U
19、SER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 9. INTERPRETATION OF DRAWING PER ARP4296. Copyright SAE International Provided
20、 by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:56:44 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, BUSHING, PIPE, INTERNAL AND EXTERNAL THREAD AS4861 REV. A AS4861 SHEET 3 OF 3 REV. A (R) 10.
21、SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TO
22、LERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030. /14/ EXAMPLE OF PART NUMBER: AS4861 J 04 A BASIC PART NUMBER CODE LETTER FOR OXYGEN SYSTEMS. /3/ THIS CODE LETTER SHALL BE THE LAST DIGIT IN THE PART NUMBER. OMIT CODE LETTER IF OXYGEN SYSTEMS ARE NOT REQUIRED MATERIAL CODE LETTER /1/ SIZE CO
23、DE, PIPE SIZE IN .125 INCREMENTS /15/ PART NUMBERS WITH MATERIAL CODE LETTER D ARE INACTIVE FOR NEW DESIGN AS OF 2004-03. USE PART NUMBERS WITH MATERIAL CODE LETTER W FOR NEW DESIGN. PART NUMBERS WITH MATERIAL CODE LETTER S ARE INACTIVE FOR NEW DESIGN AS OF 2004-03. USE PART NUMBERS WITH MATERIAL CO
24、DE LETTER R FOR NEW DESIGN. /16/ THIS DOCUMENT INCLUDES CADMIUM AS A PLATING MATERIAL. THE USE OF CADMIUM HAS BEEN RESTRICTED AND/OR BANNED FOR USE IN MANY COUNTRIES DUE TO ENVIRONMENTAL AND HEALTH CONCERNS. THE USER SHOULD CONSULT WITH LOCAL OFFICIALS ON APPLICABLE HEALTH AND ENVIRONMENTAL REGULATIONS REGARDING ITS USE. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:56:44 MSTNo reproduction or networking permitted without license from IHS -,-,-