《SAE-AS-51992A-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-51992A-2007.pdf（4页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD STUD, LOCKED IN-RING, SERRATED, HIGH STRENGTH AS51992 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or
2、 otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-04 REVISED 2007-08 THIRD ANGLE PROJECTION CUSTO
3、DIAN: SAE E-25 REV. A FEDERAL SUPPLY CLASS 5307 AS51992 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: MIL-S-45909 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely volunta
4、ry, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your writ
5、ten comments and suggestions. RATIONALE TO REVISE ERRORS THAT WERE MADE WHEN TRANSFERRING MS51992 TO AS51992. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:26:49 MSTNo reproduction or networking permitted withou
6、t license from IHS -,-,- AEROSPACE STANDARD STUD, LOCKED IN-RING, SERRATED, HIGH STRENGTH AS51992 REV. A AS51992 SHEET 2 OF 4 REV. A Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:26:49 MSTNo reproduction or netw
7、orking permitted without license from IHS -,-,- AEROSPACE STANDARD STUD, LOCKED IN-RING, SERRATED, HIGH STRENGTH AS51992 REV. A AS51992 SHEET 3 OF 4 REV. A NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCER
8、NING CADMIUMS USE. 1. DIMENSIONS: DIMENSIONS IN INCHES; TO BE MET AFTER PLATING. 2. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 3. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTE
9、D IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DoDISS) SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resa
10、le, 12/04/2007 18:26:49 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD STUD, LOCKED IN-RING, SERRATED, HIGH STRENGTH AS51992 REV. A AS51992 SHEET 4 OF 4 REV. A 5. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCAT
11、ING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:26:49 MSTNo reproduction or networking permitted without license from IHS -,-,-