《SAE-AS-21910B-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-21910B-2003-R2007.pdf（4页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 4 AS21910 REV. B AEROSPACE STANDARD AS21910 REV. B ISSUED 1998-03 REVISED
3、2003-06 REAFFIRMED 2007-07 (R) TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON SIDE CUSTODIAN: SAE G-3/G-3BPROCUREMENT SPECIFICATION: AS18280 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON SIDE RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE S
4、AE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission
5、of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not
6、 for Resale, 12/04/2007 19:36:36 MSTNo reproduction or networking permitted without license from IHS -,-,- TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON SIDE AEROSPACE STANDARD AS21910 SHEET 2 OF 4 AS21910 REV. B REV. B (R) NOTES: 1.MATERIAL: SEE PROCUREMENT SPECIFICATION. ALLOY STEEL ALUMINUM A
7、LLOY CORROSION RESISTANT STEEL TITANIUM ALLOY 2.FINISH: SEE PROCUREMENT SPECIFICATION 3.BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 4.DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016, ANGLES 030. TABLE 1A - DIMENSIONS B-U DASH NO. NOMINAL TUBE SIZE T THREAD AS
8、8879 B MIN K +.047 -.000 Q +.047 -.000 R +.047 -.000 U RAD -2 .125.3125-24 UNJF-3A.375 .625 .844 .375.063 -3 .188.3750-24 UNJF-3A.406 .688 .9061.453.094 -4 .250.4375-20 UNJF-3A.438 .7501.0941.672.094 -5 .313.5000-20 UNJF-3A.438 .7501.0941.672.094 -6 .375.5625-18 UNJF-3A.469 .8131.1561.891.125 -8 .50
9、0.7500-16 UNJF-3A.5621.0001.3442.031.125 -10 .625.8750-14 UNJF-3A.6251.1561.5002.250.125 -12 .7501.0625-12 UNJ-3A.6881.3441.6412.438.125 -161.0001.3125-12 UNJ-3A.6881.5311.8442.656.125 -201.2501.6250-12 UNJ-3A.6881.7191.9842.797.125 TABLE 1B - DIMENSIONS V-Z DASH NO.V W APPROX X APPROX Z DIA WEIGHT,
10、 LB/EA, APPROX, REF. STEEL AL ALLOY TI ALLOY -2 .500 .469 .313 .563 .051.018 .029 -3 .563 .500 .313 .625 .104.039 .060 -4 .750 .688 .438 .750 .233.083 .134 -5 .750 .688 .438 .750 .278.099 .160 -6 .875 .781 .438 .875 .326.116 .188 -81.063 .906 .5001.063 .554.197 .319 -101.063 .906 .5001.188 .579.206
11、.334 -121.3131.094 .6251.4381.012.360 .583 -161.6251.313 .7501.6881.340.455 .773 -201.8751.500 .8752.0001.950.672 1.125 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:36:36 MSTNo reproduction or networking permit
12、ted without license from IHS -,-,- TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON SIDE AEROSPACE STANDARD AS21910 SHEET 3 OF 4 AS21910 REV. B REV. B (R) 5.PART NUMBERS: DASH “-” IN PART NUMBER FOR 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE 7 /A/ ADD “V(SIZE)P” IN PLACE OF DASH FOR CORROSION
13、RESISTANT STEEL (15-5PH), CADMIUM PLATED ADD “V” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED ADD “D” IN PLACE OF DASH FOR ALUMINUM ALLOY (2024): CANCELLED AND REPLACED, SEE 7 /C/ ADD “W” IN PLACE OF DASH FOR ALUMINUM ALLOY (7075) ADD “J” IN PLACE OF DASH FOR CORROSION
14、 RESISTANT STEEL (TYPE 304) ADD “K” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (TYPE 316) ADD “R” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 321) ADD “S” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 347): CANCELLED, SEE 7 /D/ ADD “T” AFTER DASH NUMBER FOR TITANIUM ALLOY (6AL-
15、4V) EXAMPLES OF PART NUMBERS: MS21910-4TEE, .250 TUBING, 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE 7 /A/ MS21910V4PTEE, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), CADMIUM PLATED MS21910V4TEE, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED MS21910D4TEE, .250 TUBING, A
16、LUMINUM ALLOY (2024) IS CANCELLED AND REPLACED, SEE 7 /C/ MS21910W4TEE, .250 TUBING, ALUMINUM ALLOY (7075) MS21910J4TEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 304) MS21910K4TEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 316) MS21910-4RTEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 321)
17、MS21910-4STEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 347) IS CANCELLED, SEE 7 /D/ MS21910-4TTEE, .250 TUBING, TITANIUM ALLOY (6AL-4V) 6.TITANIUM NOT RECOMMENDED FOR USE IN OXYGEN SYSTEMS. 7.SEE TABLE 2 FOR CANCELLED AND SUPERSEDED DOCUMENT AND PART NUMBERS. /A/PARTS CODED “-” FOR 4130 ALLOY S
18、TEEL ARE NOT TO BE MANUFACTURED. PARTS CODED “V(SIZE)P” FOR CORROSION RESISTANT STEEL (15-5PH) WITH CADMIUM PLATE SHALL BE FURNISHED IN LIEU OF “-” CODED (4130) PARTS. PARTS CODED “-” FOR 4130 ALLOY STEEL MAY BE PROCURED UNTIL 12-31-06. /B/PARTS CODED “C” FOR CORROSION RESISTANT STEEL (TYPE 303) ARE
19、 NOT TO BE MANUFACTURED. PARTS CODED “J”, “K” OR “R” FOR CORROSION RESISTANT STEEL (TYPES 304, 316, OR 321, RESPECTIVELY) SHALL BE FURNISHED IN LIEU OF “C” CODED PARTS AT SUPPLIERS OPTION. /C/PARTS CODED “D” FOR ALUMINUM ALLOY 2024 ARE NOT TO BE MANUFACTURED. PARTS CODED “W” FOR ALUMINUM ALLOY 7075
20、SHALL BE FURNISHED IN LIEU OF 2024 (D CODE) PARTS. PARTS CODED “D” FOR ALUMINUM ALLOY 2024 MAY BE PROCURED UNTIL 12-31-06. /D/PARTS CODED “S” FOR CORROSION RESISTANT STEEL (TYPE 347) ARE NOT TO BE MANUFACTURED. PARTS CODED “S” MAY BE USED UNTIL EXISTING STOCK IS DEPLETED. PARTS CODED “R” FOR CORROSI
21、ON RESISTANT STEEL (TYPE 321) SHALL BE FURNISHED IN LIEU OF “S” CODED PARTS. TABLE 2 - CANCELLED AND SUPERSEDED DOCUMENT AND PART NUMBERS CANCELLED DOCUMENT NUMBER PART NUMBERS SUPERSESSION NOTES SUPERSEDING DOCUMENT NUMBER SUPERSEDING PART NUMBERS MS21910MS21910-(2 THRU 20)/A/AS21910MS21910V(2 THRU
22、 20)P MS21910MS21910C(2 THRU 20)/B/AS21910MS21910J(2 THRU 20), MS21910K(2 THRU 20), OR MS21910-(2 THRU 20)R MS21910MS21910D(2 THRU 20)/C/AS21910MS21910W(2 THRU 20) MS21910MS21910W(2 THRU 20)NONEAS21910MS21910W(2 THRU 20) MS21910MS21910J(2 THRU 20)NONEAS21910MS21910J(2 THRU 20) MS21910MS21910K(2 THRU
23、 20)NONEAS21910MS21910K(2 THRU 20) MS21910MS21910-(2 THRU 20)RNONEAS21910MS21910-(2 THRU 20)R MS21910MS21910-(2 THRU 20)S/D/AS21910MS21910-(2 THRU 20)R MS21910MS21910-(2 THRU 20)TNONEAS21910MS21910-(2 THRU 20)T Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply
24、 Ctr/5913977001 Not for Resale, 12/04/2007 19:36:36 MSTNo reproduction or networking permitted without license from IHS -,-,- TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON SIDE AEROSPACE STANDARD AS21910 SHEET 4 OF 4 AS21910 REV. B REV. B (R) 8.REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFEC
25、T ON DATE OF INVITATIONS FOR BID. 9.IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 10.USERS OF THIS STANDARD SHALL PROCURE THE PRODUCT FROM ACCREDITED MANUFACTURERS OR ACCREDITED DISTRIBUTORS AS LISTED IN
26、 THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.pri.sae.org/QPL/as18280.pdf FOR CURRENT QPL ONLINE. NOTE THAT MANUFACTURERS ARE ACCREDITED BY PART NUMBER, SIZE AND MATERIALS ON PRI-QPL- AS18280. 11.THE CHANGE BAR ( l ) LOCATED IN THE L
27、EFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 12.INTERPRETATION OF DRAWING PER ARP4296. 13.FLUID PASSAGE, HOLE CONTOUR: ARP4266 (OPTIONAL) Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:36:36 MSTNo reproduction or networking permitted without license from IHS -,-,-