《SAE-AS-39029-98-2000-R2006.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-39029-98-2000-R2006.pdf(4页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 4 AS39029/98 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS39029/98 ISSUED 2
3、000-07 CONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE, COAXIAL, SIZE 1 (FOR DOD-C-83527 CONNECTORS) PREPARED BY SAE SUBCOMMITTEE AE-8C1 FEDERAL SUPPLY CLASS 5935 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-39029/98A AND CONTAINS ONLY MINOR EDITORIAL A
4、ND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-39029/98A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFI
5、CATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICA
6、TIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONT
7、RACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. REAFFIRMED 2006-08 Copyright 2006 SAE International All rights reser
8、ved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canad
9、a) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:17:10 MDTNo reproduction or netwo
10、rking permitted without license from IHS -,-,- CONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE, COAXIAL, SIZE 1 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/98 SHEET 2 OF 4 AS39029/98 THE REQUIREMENTS FOR ACQUIRING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION
11、AND THE LATEST ISSUE OF MIL-C-39029. FIGURE 1. SOCKET CONTACTS. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:17:10 MDTNo reproduction or networking permitted without license from IHS -,-,- CONTACT
12、S, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE, COAXIAL, SIZE 1 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/98 SHEET 3 OF 4 AS39029/98 FIGURE 1. SOCKET CONTACTS - CONTINUED. REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Mating contact: MIL-C-39029/97A. Materials
13、: Body: Brass, half-hard or copper-beryllium. Insulator: MIL-P-19468. Crimp ferrule: Copper, annealed. Gasket: Silicone rubber. Plating: Gold as required for MIL-C-39029, type D contacts. Performance: Temperature range: -65C to +165C. Impedance: 50 ohms nominal. VSWR: 1.70:1 maximum. Frequency range
14、: 0 to 5 GHz. Insertion loss: 0.3 dB. Contact resistance: Outer contact: 0.2 milliohm maximum. Inner contact: 1.0 milliohm maximum. Rated voltage: 1,000 V rms at sea level. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for
15、Resale, 09/10/2007 03:17:10 MDTNo reproduction or networking permitted without license from IHS -,-,- CONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE, COAXIAL, SIZE 1 (FOR DOD-C-83527 CONNECTORS) AEROSPACE STANDARD AS39029/98 SHEET 4 OF 4 AS39029/98 Dielectric withstanding voltage: 2,500 V r
16、ms at sea level. Insulation resistance: 5,000 megohms minimum. Cable retention: 125 pounds minimum. Shock: Test condition D per method 2004 of MIL-STD-1344. Vibration: Test condition VI, letter J, per method 2005 of MIL-STD-1344. Directions shall be longitudinal and perpendicular. Time duration shal
17、l be 8 hours in each direction. Installation and removal: Installation and removal of contact shall be per manufacturer recommended instructions. Shipping: Figure 1 illustrates final assembly; parts are to be shipped unassembled in a suitable container. Manufacturer recommended assembly instructions
18、 shall be shipped with each unit package. QPL evaluating activity: Defense Electronics Supply Center (DESC-E), Dayton, OH 45444. Part number: M39029/98-548. TABLE I. DESIGN CHARACTERISTICS. Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 09/10/2007 03:17:10 MDTNo reproduction or networking permitted without license from IHS -,-,-