《SAE-AS-81714-11-1998-R2004.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-81714-11-1998-R2004.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS81714/11 Copyright 2004 SAE International All rights reserved. No part
3、 of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:Tel: 877-606-7323 (inside USA and Canada)Tel: 724-77
4、6-4970 (outside USA) Fax: 724-776-0790Email: custsvcsae.orgSAE WEB ADDRESS: http:/www.sae.org AEROSPACE STANDARD AS81714/11 ISSUED 1998-07 REAFFIRMED 2004-11 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SINGLE, SERIES I PREPARED BY SUBCOMMITTEE AE-8C2 FEDERA
5、L SUPPLY CLASS 5940 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-T-81714/11F AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUME
6、NT IS INTENDED TO REPLACE MIL-T-81714/11F. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACC
7、ELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. U
8、NDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. TERMINAL JUNCT
9、ION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SINGLE, SERIES I AEROSPACE STANDARD AS81714/11 SHEET 2 OF 3 AS81714/11 THE COMPLETE REQUIREMENTS FOR ACQUIRING THE WIRE IN-LINE JUNCTION DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-
10、T-81714. WIRE IN-LINE JUNCTION SINGLE BODY TABLE I. IN-LINE JUNCTIONS. TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, WIRE IN-LINE JUNCTIONS, SINGLE, SERIES I AEROSPACE STANDARD AS81714/11 SHEET 3 OF 3 AS81714/11 NOTES: 1.DIMENSIONS ARE IN INCHES. 2.TOOL FOR CONTACT INSERTING/REMOVAL
11、 SHALL BE APPROPRIATE SIZE M81969/14 AND SHALL BE ORDERED SEPARATELY (SEE TABLE I). 3.METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. 4.THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, SIZE, AND CLASS. PART NUMBER EXAMPLE: M81714/11-20D SIZE 20, CLASS D WIRE IN-LINE JUNCTION. 5.INTERNATIONAL INTEREST, SEE SPECIFICATION MIL-T-81714. 6.CLASSES A, B AND C COMPONENTS ARE INACTIVE FOR NEW DESIGN. ONLY CLASS D COMPONENTS SHALL BE USED FOR DIRECT GOVERNMENT ACQUISITION.