《SAE-AS-5194B-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5194B-2003-R2007.pdf（5页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 5 AS5194 REV. B THIRD ANGLE PROJECTION AEROSPACE STANDARD AS5194 REV. B IS
3、SUED 1998-03 REVISED 2003-08 REAFFIRMED 2007-07 FITTING, ADAPTER, STRAIGHT PIPE TO FLARED CUSTODIAN: SAE G-3/G-3BPROCUREMENT SPECIFICATION: /4/ AS4842/1 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - FITTING, ADAPTER RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copy
4、right 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT O
5、RDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:57
6、:53 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING, ADAPTER, STRAIGHT PIPE TO FLARED AEROSPACE STANDARD AS5194 SHEET 2 OF 5 AS5194 REV. B REV. B TABLE 1A - DIMENSIONS BASIC NO. AS5194 /16/ SIZE CODE (NOMINAL TUBE SIZE) PORT #1 (NOMINAL PIPE SIZE) PORT #2 T THREAD P
7、ER AS8879 CLASS 3A P THREAD PER AS71051 ANPTA B .010CD 0202.125.125 .3125-24 UNJF1/8-271.016 .418.188.062 0302.188.125 .3750-24 UNJF1/8-271.047 .418.188.124 0402.250.125 .4375-20 UNJF1/8-271.109 .480.188.172 0404.250.250 .4375-20 UNJF1/4-181.375 .542.282.172 0502.312.125 .5000-20 UNJF1/8-271.141 .54
8、2.188.234 0504.312.250 .5000-20 UNJF1/4-181.375 .542.282.234 0602.375.125 .5625-18 UNJF1/8-271.187 .605.188.297 0604.375.250 .5625-18 UNJF1/4-181.375 .605.282.297 0606.375.375 .5625-18 UNJF3/8-181.406 .730.406.297 0608.375.500 .5625-18 UNJF1/2-141.625 .855.532.297 0804.500.250 .7500-16 UNJF1/4-271.5
9、00 .792.282.391 0806.500.375 .7500-16 UNJF3/8-181.500 .792.406.391 1008.625.500 .8750-14 UNJF1/2-141.828 .918.532.484 1012.625.750 .8750-14 UNJF3/4-141.8441.103.720.484 1208.750.5001.0625-12 UNJ1/2-141.9531.103.532.609 TABLE 1B - DIMENSIONS AND WEIGHTS BASIC NO. AS5194 /16/ SIZE CODEEF G +.002/-.003
10、H M +.015/-.000 LB/EA APPROX REF AL LB/EA APPROX REF COPPER LB/EA APPROX REF STEEL 0202.469.250 .428- .440.063.00800.0243.0230 0302.469.312 .428- .440.063.00898.0273.0258 0402.469.364 .490- .502.075.0111.0338.0320 0404.688.364 .552- .565.075.0177.0538.0508 0502 .625.426 .552- .565.075.0140.0426.0402
11、 0504.688.426 .552- .565.075.0185.0562.0531 0602 .687.481 .615- .628.083.0178.0543.0513 0604.688.481 .615- .628.083.0203.0619.0585 0606.688.481 .740- .753.083.0272.0826.0780 0608.875.481 .865- .878.083.0422.129.122 0804 .844.660 .802- .815.094.0464.141.133 0806.688.660 .802- .815.094.0368.112.105 10
12、08.906.773 .928- .941.107.0583.177.167 1012.906.7731.113-1.128.107.0751.228.215 12081.062.9451.113-1.128.125.0843.256.242 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:57:53 MSTNo reproduction or networking perm
13、itted without license from IHS -,-,- FITTING, ADAPTER, STRAIGHT PIPE TO FLARED AEROSPACE STANDARD AS5194 SHEET 3 OF 5 AS5194 REV. B REV. B NOTES: /1/MATERIAL: a.DASH AS CODE LETTER - TYPE 4130 CARBON STEEL BAR PER AMS-S-6758 OR AMS 6370 OR TYPE 4140 PER AMS 6382. /2/ b.CODE LETTER B - TYPE 360 COPPE
14、R ALLOY BAR PER ASTM B 416, ASTM B 138, OR AMS 4610. c.CODE LETTER D - TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS 4112 OR TYPE 2024- T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. d.CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS 5639. e.CODE LETTER K - TYP
15、E 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS 5648. f.CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS 5645. g.CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS 4124. TABLE 1C - DIMENSIONS BAS
16、IC NO. AS5194 /16/ SIZE CODE (NOMINAL TUBE SIZE) PORT #1 (NOMINAL TUBE SIZE) PORT #2 T THREAD PER AS8879 CLASS 3A P THREAD PER AS71051 ANPTA B .010CD 1212 .750 .7501.0625-12 UNJ 3/4-141.9531.103 .720 .609 1216 .7501.0001.0625-12 UNJ 1-11.52.1871.352 .940 .609 16121.000 .7501.3125-12 UNJ 3/4-142.0311
17、.352 .720 .845 16161.0001.0001.3125-12 UNJ 1-11.52.2191.352 .940 .845 20161.2501.0001.6250-12 UNJ 1-11.52.3281.666 .9401.080 20201.2501.2501.6250-12 UNJ1-1/4-11.52.3591.6661.2531.080 24201.5001.2501.8750-12 UNJ1-1/4-11.52.5471.9781.2531.314 28241.7501.5002.2500-12 UNJ1-1/2-11.52.8282.3491.5031.550 3
18、2322.0002.0002.5000-12 UNJ 2-11.53.1092.5991.9411.784 TABLE 1D - DIMENSIONS AND WEIGHTS BASIC NO. AS5194 /16/ SIZE CODEEF G +.002/-.003H M +.015/-.000 LB/EA APPROX REF AL LB/EA APPROX REF COPPER LB/EA APPROX REF STEEL 1212 .906 .9451.113-1.128.125.0873 .266 .250 12161.062 .9451.362-1.380.125.130 .39
19、3 .371 16121.0311.1951.362-1.380.125.122 .373 .352 16161.1251.1951.362-1.380.125.136 .413 .390 20161.2501.5071.676-1.693.125.213 .648 .612 20201.1871.5071.676-1.693.125.207 .629 .594 24201.3441.7561.988-2.005.125.294 .894 .844 28241.4372.1312.359-2.385.125.4541.381.30 32321.4372.3812.609-2.635.125.8
20、722.652.50 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:57:53 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING, ADAPTER, STRAIGHT PIPE TO FLARED AEROSPACE STANDARD AS5194 SHEET
21、4 OF 5 AS5194 REV. B REV. B NOTES (CONTINUED): /2/HEAT TREATMENT: a.DASH AS CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b.OTHER CODE LETTERS - NONE. 3.FINISH: a.DASH AS CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 2 AND COAT WITH A LIGHT FILM OF OIL PER PROCUREM
22、ENT SPECIFICATION. b.CODE LETTER B - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 3 OR NONE. c.CODE LETTER D - ANODIZE PER AMS 2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. d.CODE LETTERS J, K, AND R - PASSIVATE PER AMS-QQ-P-35, TYPE VI OR VII. e.CODE LETTE
23、R W - ANODIZE PER AMS 2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. /4/PROCUREMENT SPECIFICATION: AS4842/1 EXCEPT AS SPECIFIED ON THIS STANDARD. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S) OR ACCREDITED DISTRIBUTOR(S
24、) AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURERS LIST (QML) FOR THIS TYPE PRODUCT. /5/IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a.SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND MATERIAL CO
25、DE LETTER. b.SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6.INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 7.INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES
26、AS FOLLOWS: a.SIZES 02 THROUGH 16 IN CARBON STEEL, CORROSION RESISTANT STEEL AND COPPER ALLOY AT 3000 psi. b.SIZES 12 THROUGH 20 IN ALUMINUM ALLOY AT 3000 psi. c.SIZE 16 IN ALUMINUM ALLOY AND SIZES 20 THROUGH 32 IN CARBON STEEL, CORROSION RESISTANT STEEL AND COPPER ALLOY AT 1500 psi. THIS STANDARD I
27、S THE FUNCTIONAL EQUIVALENT OF AN816 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. /8/THE INTERNAL DIAMETERS C AND D SHALL END IN A CONICAL END OF 110 MINIMUM INCLUDED ANGLE. AT THE OPTION OF THE MANUFACTURER, THE SMALLER DIAMETER MAY BE MACHINED THROUGH THE FITTING FROM END TO END. /9/T
28、HE HEX CORNERS MAY BE ROUNDED PER ARP1942. 10.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE
29、INDICATES A COMPLETE REVISION OF THE DOCUMENT. 11.INTERPRETATION OF DRAWING PER ARP4296. 12.SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. Copyright SAE International Provi
30、ded by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:57:53 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING, ADAPTER, STRAIGHT PIPE TO FLARED AEROSPACE STANDARD AS5194 SHEET 5 OF 5 AS5194 REV. B REV. B NOTES (CONTINUED
31、): 13.BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 14.DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 15.DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 030. /16/ Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:57:53 MSTNo reproduction or networking permitted without license from IHS -,-,-