《SAE-AS-5171-1997-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5171-1997-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS5171 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS5171 ISSUED 1997-10 R
3、EAFFIRMED 2007-11 WASHER, FLAT, FITTING, FLARED AND FLARELESS CUSTODIAN: SAE G-3/G-3BPROCUREMENT SPECIFICATION: NONE /4/ FEDERAL SUPPLY CLASS 4730 FIGURE 1 - WASHER TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS5171 /10/ SIZE AND THICKNESS CODE (NOMINAL TUBE SIZE) A .005 D +.020/.005F T ALUM T STEEL,
4、 CRES LB/100 MAX ALUM LB/100 MAX STEEL, CRES 02-16.125.338.562.007.013-.019.014-.018.0290.0842 02-32.125.338.562.007.028-.036.028-.036.0581.168 02-63.125.338.562.007.057-.069.057-.069.114.332 03-16.188.400.625.007.013-.019.014-.018.0332.0962 03-32.188.400.625.007.028-.036.028-.036.0664.192 03-63.188
5、.400.625.007.057-.069.057-.069.131.379 04-16.250.462.750.007.013-.019.014-.018.0498.144 04-32.250.462.750.007.028-.036.028-.036.0996.289 04-63.250.462.750.007.057-.069.057-.069.196.569 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a re
6、trieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Custom
7、erServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:45:10 MSTNo reproduction or networking permitted without license from IHS -,-,- WASHER, FLAT, FITTING, FLARED AND
8、 FLARELESS AEROSPACE STANDARD AS5171 SHEET 2 OF 3 AS5171 TABLE 1A - DIMENSIONS AND WEIGHTS BASIC NO. AS5171 /10/ SIZE AND THICKNESS CODE (NOMINAL TUBE SIZE) A .005 D +.020/.005F T ALUM T STEEL, CRES LB/100 MAX ALUM LB/100 MAX STEEL, CRES 05-16 .312 .525 .875.007.013-.019.014-.018 .0696 .202 05-32 .3
9、12 .525 .875.007.028-.036.028-.036 .139 .403 05-63 .312 .525 .875.007.057-.069.057-.069 .274 .794 06-16 .375 .5881.062.010.013-.019.014-.018 .110 .320 06-32 .375 .5881.062.010.028-.036.028-.036 .221 .640 06-63 .375 .5881.062.010.057-.069.057-.069 .434 1.26 08-16 .500 .7751.312.010.013-.019.014-.018
10、.158 .457 08-32 .500 .7751.312.010.028-.036.028-.036 .315 .914 08-90 .500 .7751.312.010.083-.097.082-.098 .887 2.57 10-16 .625 .9001.500.010.013-.019.014-.018 .202 .586 10-32 .625 .9001.500.010.028-.036.028-.036 .404 1.17 10-90 .625 .9001.500.010.083-.097.082-.0981.14 3.30 12-16 .7501.0881.812.010.0
11、13-.019.014-.018 .294 .852 12-32 .7501.0881.812.010.028-.036.028-.036 .588 1.70 12-90 .7501.0881.812.010.083-.097.082-.0981.65 4.80 14-16 .8751.2121.936.015.013-.019.014-.018 .319 .925 14-32 .8751.2121.936.015.028-.036.028-.036 .638 1.85 14-90 .8751.2121.936.015.083-.097.082-.0981.79 5.20 16-161.000
12、1.3382.062.015.013-.019.014-.018 .344 .999 16-321.0001.3382.062.015.028-.036.028-.036 .689 2.00 16-901.0001.3382.062.015.083-.097.082-.0981.94 5.62 20-161.2501.6502.375.015.013-.019.014-.018 .408 1.18 20-321.2501.6502.375.015.028-.036.028-.036 .817 2.37 20-901.2501.6502.375.015.083-.097.082-.0982.30
13、 6.66 24-161.5001.9002.625.015.013-.019.014-.018 .459 1.33 24-321.5001.9002.625.015.028-.036.028-.036 .918 2.66 24-901.5001.9002.625.015.083-.097.082-.0982.58 7.49 28-161.7502.2753.000.015.013-.019.014-.018 .535 1.55 28-321.7502.2753.000.015.028-.036.028-.0361.07 3.10 28-901.7502.2753.000.015.083-.0
14、97.082-.0983.01 8.72 32-162.0002.5253.250.015.013-.019.014-.018 .586 1.70 32-322.0002.5253.250.015.028-.036.028-.0361.17 3.40 32-902.0002.5253.250.015.083-.097.082-.0983.29 9.55 40-162.5003.0253.750.015.013-.019.014-.018 .687 1.99 40-322.5003.0253.750.015.028-.036.028-.0361.37 3.98 40-902.5003.0253.
15、750.015.083-.097.082-.0983.8611.2 48-163.0003.5254.250.015.013-.019.014-.018 .788 2.28 48-323.0003.5254.250.015.028-.036.028-.0361.58 4.57 48-903.0003.5254.250.015.083-.097.082-.0984.4312.8 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not f
16、or Resale, 12/04/2007 20:45:10 MSTNo reproduction or networking permitted without license from IHS -,-,- WASHER, FLAT, FITTING, FLARED AND FLARELESS AEROSPACE STANDARD AS5171 SHEET 3 OF 3 AS5171 NOTES: /1/MATERIAL: a.DASH AS CODE LETTER - TYPE 1020 OR 1025 STEEL SHEET OR STRIP PER MIL-S-7952. b.CODE
17、 LETTER C - TYPE 301, 302, 304 OR 316 CORROSION RESISTANT STEEL SHEET OR STRIP PER MIL-S- 5059, TYPE 321 CORROSION RESISTANT STEEL SHEET OR STRIP PER AMS 5510 OR TYPE 347 CORROSION RESISTANT STEEL SHEET OR STRIP PER AMS 5512. c.CODE LETTER D - TYPE 2024 ALCLAD ALUMINUM ALLOY SHEET PER QQ-A-250/5, CO
18、NDITION T3 OR T4. /2/FINISH: a.DASH AS MATERIAL CODE LETTER - CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 2. b.MATERIAL CODE LETTER C - PASSIVATE PER QQ-P-35, TYPE VI OR VII. c.MATERIAL CODE LETTER D - (1)D CODE PARTS TO BE CHEMICAL SURFACE TREATED ONLY WILL HAVE THE FINISH CODE LETTER “J” AFTER THE
19、THICKNESS CODE IN THE PART NUMBER. THE FINISH WILL BE: CHEMICAL SURFACE TREAT PER MIL-C-5541, CLASS 3. (J CODE PARTS ARE INTENDED FOR USE WHEN LOW ELECTRICAL RESISTANCE IS REQUIRED.) (2)D CODE PARTS TO BE ANODIZED ONLY WILL HAVE THE FINISH CODE LETTER “K” AFTER THE THICKNESS CODE IN THE PART NUMBER.
20、 THE FINISH WILL BE: ANODIZE PER AMS 2471. (K CODE PARTS ARE INTENDED FOR USE WHERE CORROSION PROTECTION IS THE PRIME CONSIDERATION.) /3/IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 METHOD 30, MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, BASIC PART NUMBER AND MATERIAL CODE LETTER. /4/THIS PART IS
21、 DESIGNED FOR USE WITH AS4377 AND AS4396 FITTING ENDS WITH AN AS4178 NUT IN BULKHEAD MOUNTING APPLICATIONS. 5.INTERPRETATION OF DRAWING PER ARP4296. 6.SURFACE TEXTURE: SYMBOLS PER ASME Y14.5M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 m Ra. 7.BREAK EDGES .0
22、03 TO .015 UNLESS OTHERWISE SPECIFIED. 8.DIMENSIONING AND TOLERANCING: ASME Y14.5M. 9.DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 030. /10/ Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:45:10 MSTNo reproduction or networking permitted without license from IHS -,-,-