《SAE-AS-5009-1997-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5009-1997-R2007.pdf（2页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 2 AS5009 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS5009 ISSUED 1997-11 R
3、EAFFIRMED 2007-11 FITTING, ELBOW, 90, EXTERNAL SWAGE, HYDRAULIC CUSTODIAN: SAE COMMITTEE G-3/G-3BPROCUREMENT SPECIFICATION: /5/ AS4459 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - ELBOW, 90, EXTERNAL SWAGE TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS5009 /14/ SIZE CODE NOMINAL TUBE SIZE A +.030 .000 B .015
4、 C +.000 .003 D +.030 .000E F +.030 .000G V /2/AA LB/EA MAX CRES LB/EA MAX TI LB/EA MAX AL 03 .188 .860 .325 .275 .860.182/.187 .715 .195/ .198.170/.220.13.0140.00800.00500 04 .2501.050 .390 .3381.050.244/.249 .915 .257/ .260.190/.240.22.0250.0140.00900 05 .3121.120 .465 .4131.120.303/.308 .955 .319
5、/ .322.200/.250.22.0330.0190.0110 06 .3751.190 .545 .4801.190.366/.371 .990 .382/ .385.220/.270.22.048.0270.0160 08 .5001.755 .705 .6551.755.482/.4891.493 .508/ .511.410/.435.50.116.0660.0400 10 .6251.860 .861 .7871.860.606/.6141.533 .633/ .636.410/.435.50.167.0950.0570 12 .7501.9901.036 .9291.990.7
6、31/.7391.603 .758/ .761.365/.390.50.234.134.0810 161.0002.3441.3801.2572.344.981/.9891.7481.008/1.011.325/.350.50.541.307.185 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
7、 electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyrig
8、ht SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:09:52 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING, ELBOW, 90, EXTERNAL SWAGE, HYDRAULIC AEROSPACE STANDARD AS5009 SHEET 2 OF 2 AS5009
9、NOTES: /1/MATERIAL: a.CODE LETTER “”: 21-6-9 CRES BAR PER AMS 5656 b.CODE LETTER “E”: COMMERCIALLY PURE TITANIUM BAR PER AMS 4921 c.CODE LETTER “D”: 6061T6 ALUMINUM ALLOY PER AMS 4150 /2/FINISH: a.MATERIAL CODE “”: PASSIVATE PER QQ-P-35 TYPE VII, PTFE COAT (COLOR GREEN) BORE DIAMETER TO “V” DEPTH, O
10、VERSPRAY ON “Y” PERMISSIBLE. b.MATERIAL CODE “E”: PTFE COAT (COLOR BLACK) EXTERIOR SURFACES AND BORE DIAMETER TO “V” DEPTH UNLESS OTHERWISE SPECIFIED, SEE NOTE /14/. AA TO BE FREE OF PTFE COATING. c.MATERIAL CODE “D”: CHEMICAL FILM FINISH ENTIRE PART (INCLUDING INTERNAL DIAS) PER MIL-C-5541, CLASS 1
11、A, PTFE COAT (GREEN) EXTERNAL SURFACE AND BORE DIAMETER TO “V” DEPTH. 3.LIQUID PENETRANT INSPECT PER ASTM E 1417 TYPE 1 SENSITIVITY 2. LINEAR INDICATIONS PROHIBITED, ROUNDED INDICATIONS ACCEPTABLE. /4/FILL OUTER GROOVE FOR CRES AND TITANIUM WITH SILICONE. FILL ALL GROOVES FOR ALUMINUM WITH SILICONE
12、ELASTOMER. /5/THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS. 6.SPECIFIC DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIE
13、D AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /7/IDENTIFICATION: PARTS SHALL BE IDENTIFIED IN THE AREA SHOWN PER AS4459. 8.INTENDED USE: PER AS4459. 9.INTERPRETATION OF DRAWING PER ARP4296. 10.SURFACE TEXTURE: SYMBOLS P
14、ER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 m Ra. 11.BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12.DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13.DIMENSIONS IN INCHES; UNLESS OTHERWISE SPECIFIED, TOLERANCES: DIMENSIONS LINEAR .010, ANGULAR 2. /14/ Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:09:52 MSTNo reproduction or networking permitted without license from IHS -,-,-