《SAE-AS-5947-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-5947-2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD FITTING, FERRULE END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD AS5947 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechani
2、cal, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2007-07 THIRD ANGLE
3、PROJECTION CUSTODIAN: SAE G-3/G-3A FEDERAL SUPPLY CLASS 4730 AS5947 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: NONE /1/ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely volun
4、tary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your wr
5、itten comments and suggestions. RATIONALE THIS DESIGN STANDARD PROVIDES THE DIMENSIONAL REQUIREMENTS FOR AS1730 FITTING ENDS. FIGURE 1 - FITTING END DESIGN Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:25:19 MST
6、No reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, FERRULE END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD AS5947 AS5947 SHEET 2 OF 3 TABLE 1 - DIMENSIONS NOTES: /1/ INTENDED USE: THIS FITTING END IS DESIGNED FOR USE WITH FITTINGS PER AS1
7、730. 2. INTERPRETATION OF DRAWING PER ARP4296. /3/ ALUMINUM ALLOY PARTS UTILIZING THIS END STANDARD SHALL BE FINISHED WITH ANODIZE. SURFACES NOTED SHALL BE FREE OF ANODIZE. SURFACES FREE OF ANODIZE SHALL BE CHEMICAL CONVERSION COATED. /4/ “E” IS THE MINIMUM LENGTH REQUIRED FOR ASSEMBLY WITH AN AS173
8、4 NUT AND AS1736 WASHER. /5/ USE “C1” FOR THE FLANGE THICKNESS IF MACHINED FROM A CASTING. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. 7. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONING
9、 AND TOLERANCING PER ASME Y14.5M-1994. 9. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 030. BASIC NO. AS5947 /10/ SIZE CODE NOM TUBE SIZE A .0025 B .0025 C /5/ C1 D /4/ E MIN 04 .250 .5155 .3775 .065 .080 .204 .888 05 .312 .5685 .4395 .065
10、.080 .267 .888 06 .375 .6235 .5025 .065 .080 .329 .888 08 .500 .7485 .6275 .065 .080 .454 .888 10 .625 .8865 .7525 .065 .085 .579 .897 12 .750 1.0165 .8925 .065 .085 .704 .897 16 1.000 1.2655 1.1445 .065 .085 .940 .897 20 1.250 1.5155 1.3945 .065 .085 1.190 .957 24 1.500 1.7645 1.6445 .065 .085 1.41
11、2 .989 28 1.750 2.0265 1.8975 .095 .115 1.662 1.019 32 2.000 2.2765 2.1475 .095 .115 1.912 1.019 36 2.250 2.5265 2.3975 .095 .115 2.144 1.090 40 2.500 2.7805 2.6475 .095 .115 2.394 1.090 44 2.750 3.0265 2.8975 .095 .115 2.644 1.090 48 3.000 3.3715 3.1475 .095 .115 2.894 1.090 56 3.500 3.8715 3.6475
12、.095 .120 3.394 1.090 64 4.000 4.3715 4.1575 .095 .120 3.880 1.090 72 4.500 4.8715 4.6575 .095 .120 4.380 1.208 80 5.000 5.3545 5.1575 .095 .120 4.880 1.208 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:25:19 MS
13、TNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD FITTING, FERRULE END - THREADED COUPLING, RIGID, SELF-BONDING, DESIGN STANDARD AS5947 AS5947 SHEET 3 OF 3 /10/ EXAMPLE OF DRAWING CALLOUT: a. TABULATED PART CALLOUT: FITTING END PER AS5947 b. INDIVIDUAL CALLOU
14、T: AS5947 - 08 FITTING SIZE CODE (.500 FITTING SIZE) (SEE TABLE 1) BASIC STANDARD NUMBER Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:25:19 MSTNo reproduction or networking permitted without license from IHS -,-,-