《SAE-AS-85049-137-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-85049-137-2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, FIBER OPTIC BACKSHELL, SPLIT, 90, SELF-LOCKING CATEGORY 3B FOR MIL-DTL- 38999 SERIES III AND AS5590/1 CONNECTORS AS85049/137 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
2、 transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org
3、SAE WEB ADDRESS: http:/www.sae.org ISSUED 2007-06 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS85049/137 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical
4、and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which tim
5、e it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE NEW ACCESSORIES TO COMPLEMENT MIL-DTL-38999 SERIES III AND AS5590 FIBER OPTIC CONNECTORS. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET
6、AND THE LATEST ISSUE OF: SAE AS85049. FIGURE 1 - CONFIGURATION AND DIMENSIONS Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:12:43 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPA
7、CE STANDARD CONNECTOR ACCESSORIES, FIBER OPTIC BACKSHELL, SPLIT, 90, SELF-LOCKING CATEGORY 3B FOR MIL-DTL- 38999 SERIES III AND AS5590/1 CONNECTORS AS85049/137 AS85049/137 SHEET 2 OF 3 TABLE 1 - SHELL SIZE AND DIMENSIONS SHELL SIZE SHELL SIZE CODE (REF) ARRANGEMENT NUMBER A MAX DIA B .03 (0.8) DIA C
8、 .03 (0.8) DIA D MAX DIM E MAX DIM F MAX DIM GROMMET IDENT NUMBER GROMMET HOLES -1 .86 .63 .47 1.03 1.339 1.995 9-1 1 09 A -2 (21.8) (16.0) (11.9) (26.2) (34.01) (50.67) 9-2 2 -2 .98 .63 .47 1.10 1.465 2.055 11-2 2 11 B -4 (24.9) (16.0) (11.9) (27.9) (37.21) (52.20) 11-4 4 -4 1.16 .87 .71 1.16 1.589
9、 2.125 13-4 4 13 C -5 (29.5) (22.1) (18.0) (29.5) (40.36) (53.98) 13-5 5 -5 1.28 .87 .71 1.22 1.715 2.185 15-5 5 15 D -6 (32.5) (22.1) (18.0) (31.0) (43.56) (55.50) 15-6 6 -6 1.41 1.17 1.01 1.31 1.901 2.245 17-6 6 17 E -8 (35.8) (29.7) (25.7) (33.3) (48.29) (57.02) 17-8 8 -11 1.52 1.17 1.01 1.37 2.0
10、25 2.263 19-11 11 19 F -12 (38.6) (29.7) (25.7) (34.8) (51.44) (57.48)19-12 12 -16 1.64 1.42 1.26 1.37 2.025 2.405 21-16 16 21 G -21 (41.7) (36.1) (32.0) (34.8) (51.44) (61.09)21-21 21 -21 1.77 1.73 1.57 1.44 2.152 2.435 23-21 21 23 H -25 (45.0) (43.9) (39.9) (36.6) (54.66) (61.85)23-25 25 -29 1.89
11、1.73 1.57 1.56 2.403 2.495 25-29 29 25 J -37 (48.0) (43.9) (39.9) (39.6) (61.04) (63.37)25-37 37 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. DIMENSIONS ARE IN INCHES, METRIC EQUI
12、VALENTS IN PARENTHESIS ARE FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1.000 in (25.40 mm). 2. DIMENSIONS APPLY AFTER PLATING. ACCESSORY CONFIGURATION IS OPTIONAL WITHIN THE DIMENSION ENVELOPE SPECIFIED IN FIGURE 1/TABLE 1. 3. ADAPTER LENGTH IS MEASURED FROM THE BOTTOM OF THE ACCESSORY TEETH TO
13、THE SPLIT CENTERLINE OF THE ELBOW. 4. SPLIT SECTION RETENTION, GROMMET COMPRESSION, AND TERMINATION OF OVERALL/INDIVIDUAL BRAID (AS APPLICABLE) ACCOMPLISHED BY INSTALLING AS85049/128 BAND. 5. PART SUPPLIED WITH STANDARD DETENTED SELF-LOCKING WHICH PROVIDES A POSITIVE AUDIBLE DETENTED COUPLING. OPTIO
14、N N IS A FREE SPINNING SELF-LOCKING COUPLING. 6. NUMBER OF FILLER PLUGS SUPPLIED: ARRANGEMENT; -1 & -2 = 0 ea, -4, -5, -6, & -8 = 1 ea, -11, -12, & -16 = 2 ea, -21, -25, & -29 = 3 ea, & -37 = 4 ea. REQUIREMENTS: DESIGN AND CONSTRUCTION: DIMENSIONS AND CONFIGURATION: SEE FIGURE 1 AND TABLE 1. INTERFA
15、CE DIMENSIONS: SHALL CONFORM TO AS85049, FIGURE 3. COUPLING NUT: SHALL BE CAPTIVATED TO THE ADAPTER BODY AND ROTATABLE. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:12:43 MSTNo reproduction or networking permit
16、ted without license from IHS -,-,- AEROSPACE STANDARD CONNECTOR ACCESSORIES, FIBER OPTIC BACKSHELL, SPLIT, 90, SELF-LOCKING CATEGORY 3B FOR MIL-DTL- 38999 SERIES III AND AS5590/1 CONNECTORS AS85049/137 AS85049/137 SHEET 3 OF 3 MATERIAL AND FINISH: ADAPTER, COUPLINGS: IN ACCORDANCE WITH AS85049 AND T
17、ABLE 2 HEREIN. GROMMET: IN ACCORDANCE WITH AS85049. TABLE 2 MATERIAL AND FINISH MATERIAL FINISH COMPOSITE (CONDUCTIVE) 1/ J CADMIUM OLIVE DRAB M ELECTROLESS NICKEL COMPOSITE (NON CONDUCTIVE) T COMPOSITE MATERIAL NO PLATING 1/ COUPLING NUT MAY BE UNPLATED. VIBRATION: BACKSHELLS SHALL BE SUBJECTED TO
18、TEST PARAMETERS OF APPLICABLE CONNECTOR SPECIFICATIONS. THE COUPLING TORQUE SHALL BE WITHIN +20/-10 in-lb OF THE INITIAL VALUE. ADDITIONAL TESTS FOR FINISH J, M, AND T SHALL BE AS FOLLOWS: OZONE EXPOSURE (FINISH J AND M ONLY): BACKSHELL SHALL BE TESTED IN ACCORDANCE WITH EIA364-14. SAMPLE PREPARATIO
19、N: NOT APPLICABLE FAILURE: BLISTERING OR PEALING OF THE PLATING CONSTITUTES A FAILURE. FLUID IMMERSION: BACKSHELL SHALL BE TESTED IN ACCORDANCE WITH AS85049. AFTER IMMERSION THE BACKSHELLS SHALL MEET THE COUPLING STRENGTH REQUIREMENTS OF AS85049. QUALIFICATION: QUALIFICATION: SEE AS85049, CATEGORY 3B. EXCEPT CABLE PULLOUT SHALL BE 5 lb MINIMUM PER CABLE. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:12:43 MSTNo reproduction or networking permitted without license from IHS -,-,-