《SAE-AS-85049-26A-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-85049-26A-2007.pdf（6页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SERIES III CONNECTORS) AS85049/26 Copyright 2007 SAE International All rights reserve
2、d. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)
3、 Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-07 REVISED 2007-10 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 REV. A FEDERAL SUPPLY CLASS 5935 AS85049/26 SHEET 1 OF 6 REV. A PROCUREMENT SPECIFICATION: NONE SAE Tec
4、hnical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is
5、the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE REVISE COMPLETELY UPDATE FORMAT. INCLUDE OUTSTANDING COMMENTS. NOTICE THE REQUIREM
6、ENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS85049. FIGURE 1 - CONFIGURATION AND DIMENSIONS Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007
7、18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SER
8、IES III CONNECTORS) AS85049/26 SHEET 2 OF 6 REV. A TABLE 1 - FIGURE 1 DIMENSIONS FOR CONNECTOR SHELL SIZE (REF) DASH NUMBER AS81703 SERIES 3 MIL-DTL-26482 SERIES 2 MIL-DTL-5015 CRIMP MIL-DTL-83723 SERIES III M85049/26-2 RING, SHIELD CRIMP (REF) -3 3 - - - -8 -8 - 8 8S 8 -8 -10 - 10 10S, 10SL 10 -10
9、-12 7 12 12S & 12 12 -12 -14 12 14 14S & 14 14 -14 -16 19 16 16S & 16 16 -16 -18 27 18 18 18 -18 -20 37 20 20 20 -20 -22 - 22 22 22 -22 -24 - 24 24 24 -24 -28 - - 28 - -28 -32 - - 32 - -32 -36 - - 36 - -36 -40 - - 40 - -40 -44 - - 44 - -44 -48 - - 48 - -46 -61 61 - - - -61 TABLE 1 - FIGURE 1 DIMENSI
10、ONS (CONTINUED) DASH NUMBER A .031 DIA B +.000/-.062 DIM C MAX DIM D .031 DIM E .015 DIA F .010 DIA -3 .669 (17.0) .540 (13.7) 1.277 (32.4) .926 (23.5) .250 ( 6.4) .337 ( 8.6) -8 .617 (15.7) .540 (13.7) 1.277 (32.4) .926 (23.5) .250 ( 6.4) .337 ( 8.6) -10 .734 (18.6) .540 (13.7) 1.277 (32.4) .926 (2
11、3.5) .325 ( 8.3) .488 (12.4) -12 .858 (21.8) .540 (13.7) 1.277 (32.4) .926 (23.5) .420 (10.7) .500 (12.7) -14 .984 (25.0) .540 (13.7) 1.277 (32.4) .926 (23.5) .540 (13.7) .620 (15.7) -16 1.112 (28.2) .540 (13.7) 1.277 (32.4) .926 (23.5) .670 (17.0) .750 (19.1) -18 1.218 (30.9) .540 (13.7) 1.277 (32.
12、4) .926 (23.5) .789 (20.0) .880 (22.4) -20 1.345 (34.2) .540 (13.7) 1.277 (32.4) .926 (23.5) .914 (23.2) 1.000 (25.4) -22 1.468 (37.3) .540 (13.7) 1.277 (32.4) .926 (23.5) 1.039 (26.4) 1.120 (28.4) -24 1.593 (40.5) .540 (13.7) 1.277 (32.4) .926 (23.5) 1.112 (28.2) 1.192 (30.3) -28 1.969 (50.0) .702
13、(17.8) 1.439 (36.6) .926 (23.5) 1.389 (35.3) 1.545 (39.2) -32 2.219 (56.4) .702 (17.8) 1.439 (36.6) .926 (23.5) 1.635 (41.5) 1.795 (45.6) -36 2.469 (62.7) .702 (17.8) 1.439 (36.6) .926 (23.5) 1.850 (47.0) 2.045 (51.9) -40 2.719 (69.1) .702 (17.8) 1.439 (36.6) .926 (23.5) 2.065 (52.5) 2.295 (58.3) -4
14、4 2.969 (75.4) .702 (17.8) 1.439 (36.6) .926 (23.5) 2.320 (58.9) 2.545 (64.6) -48 3.219 (81.8) .702 (17.8) 1.439 (36.6) .926 (23.5) 2.570 (65.3) 2.795 (71.0) -61 1.653 (42.0) .540 (13.7) 1.277 (32.4) .926 (23.5) 1.210 (30.7) 1.359 (34.5) Copyright SAE International Provided by IHS under license with
15、 SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015
16、 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SERIES III CONNECTORS) AS85049/26 SHEET 3 OF 6 REV. A FIGURE 2 - CONFIGURATION AND DIMENSIONS TABLE 2 - FIGURE 2 DIMENSIONS A DIA B DIA DASH NUMBER COLOR CODE MIN MAX MIN MAX L .020 DIM -8 GREEN .400 (10.2) .410 (10.4) .448 (11.4) .4
17、58 (11.6) .250 ( 6.4) -10 RED .585 (14.9) .595 (15.1) .660 (16.8) .680 (17.3) .440 (11.2) -12 RED .585 (14.9) .595 (15.1) .660 (16.8) .680 (17.3) .440 (11.2) -14 BLUE .705 (17.9) .715 (18.2) .780 (19.8) .800 (20.3) .440 (11.2) -16 GRAY .835 (21.2) .845 (21.5) .910 (23.1) .930 (23.6) .440 (11.2) -18
18、BROWN 1.005 (25.5) 1.015 (25.8) 1.080 (27.4) 1.100 (27.9) .440 (11.2) -20 GREEN 1.125 (28.6) 1.135 (28.8) 1.200 (30.5) 1.220 (31.0) .440 (11.2) -22 PINK 1.245 (31.6) 1.255 (31.9) 1.320 (33.5) 1.340 (34.0) .440 (11.2) -24 ORANGE 1.327 (33.7) 1.337 (34.0) 1.402 (35.6) 1.422 (36.1) .440 (11.2) -28 RED
19、1.665 (42.3) 1.675 (42.5) 1.740 (44.2) 1.760 (44.7) .440 (11.2) -32 GRAY 1.915 (48.6) 1.925 (48.9) 1.990 (50.5) 2.010 (51.1) .440 (11.2) -36 GREEN 2.165 (55.0) 2.175 (55.2) 2.240 (56.9) 2.260 (57.4) .440 (11.2) -40 ORANGE 2.415 (61.3) 2.425 (61.6) 2.490 (63.2) 2.510 (63.8) .440 (11.2) -44 YELLOW 2.6
20、65 (67.7) 2.675 (67.9) 2.740 (69.6) 2.760 (70.1) .440 (11.2) -48 BLUE 2.915 (74.0) 2.925 (74.3) 2.990 (75.9) 3.010 (76.5) .440 (11.2) -61 PURPLE 1.435 (36.4) 1.445 (36.7) 1.510 (38.4) 1.530 (38.9) .440 (11.2) TABLE 2 - FIGURE 2 DIMENSIONS (CONTINUED) DASH NUMBER FOR USE WITH BACKSHELLS (REF) FOR USE
21、 WITH BACKSHELLS (REF) FOR USE WITH BACKSHELLS (REF) INSTALLING DIE CAT. NO. SEE NOTE 5 -8 M85049/26-1-8 M85049/20-9 M85049/33-2-8 GS405 -10 M85049/26-1-10 M85049/20-11 M85049/33-2-10 GS590 -12 M85049/26-1-12 M85049/20-13 M85049/33-2-12 GS590 -14 M85049/26-1-14 M85049/20-15 M85049/33-2-14 GS710 -16
22、M85049/26-1-16 M85049/20-17 M85049/33-2-16 GS840 -18 M85049/26-1-18 M85049/20-19 M85049/33-2-18 GS1010 -20 M85049/26-1-20 M85049/20-21 M85049/33-2-20 GS1130 -22 M85049/26-1-22 M85049/20-23 M85049/33-2-22 GS1250 -24 M85049/26-1-24 M85049/20-25 M85049/33-2-24 GS1332 -28 M85049/26-1-28 - - GS1670 -32 M
23、85049/26-1-32 - - GS1920 -36 M85049/26-1-36 - - GS2170 -40 M85049/26-1-40 - - GS2420 -44 M85049/26-1-44 - - GS2670 -48 M85049/26-1-48 - - GS2920 -61 M85049/26-1-61 - - GS1440 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/0
24、4/2007 18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83
25、723 SERIES III CONNECTORS) AS85049/26 SHEET 4 OF 6 REV. A FIGURE 3 - CONFIGURATION NOTES: 1. DIMENSIONS ARE IN INCHES. 2. METRIC EQUIVALENTS IN PARENTHESIS ( ) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1.00 in = 25.4 mm. 3. DIMENSIONS APPLY AFTER PLATING. 4. FIGURE 2 IS DESIGNED FOR
26、USE WITH FIGURE 1. 5. CRIMP TOOL SHALL BE THE THOMAS AND BETTS INSTALLING HEAD CAT. NO. 13640, OR EQUIVALENT, SEE TABLE 2. 6. THE INSTALLING DIES (THOMAS AND BETTS CAT. NO.) SHALL BE USED WITH THE THOMAS AND BETTS INSTALLING HEAD CAT. NO. 13640, OR USE AN EQUIVALENT TOOL. REQUIREMENTS: 1. DESIGN AND
27、 CONSTRUCTION: a. DIMENSIONS AND CONFIGURATION: SEE FIGURES 1, 2, AND 3 AND TABLES 1 AND 2. b. INTERFACE DIMENSIONS SHALL CONFORM TO AS85049, FIGURE 4 OR 4A. c. FIGURE 1 CONSISTS OF A COUPLING NUT AND FOLLOWER. THE COUPLING NUT SHALL BE CAPTIVATED TO AND FREE TO ROTATE ON THE FOLLOWER 2. MATERIAL AN
28、D FINISH: SEE TABLE 3. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACK
29、SHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015 CRIMP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SERIES III CONNECTORS) AS85049/26 SHEET 5 OF 6 REV. A TABLE 3 - MATERIAL AND FINISH FIGURE MATERIAL FINISH 1 ALUMINUM ALLOY IN ACCORDANCE WITH AS850
30、49 1/ N, 2/ W 2 COPPER, ASTM B 75, ASTM B 88, ROCKWELL F-50 MAX. OR OFHC COPPER, CDA 102 OR APPROVED EQUIVALENT TIN PLATE IN ACCORDANCE WITH ASTM B 545, COLOR CODED PER TABLE (SEE FIGURE 2) CONNECTOR ACCESSORY - ALUMINUM ALLOY IN ACCORDANCE WITH AS85049 1/ N, 2/ W 3 CRIMP RING - COPPER, ASTM B 75, A
31、STM B 88, ROCKWELL F-50 MAX. OR OFHC COPPER, CDA 102 OR APPROVED EQUIVALENT TIN PLATE IN ACCORDANCE WITH ASTM B 545, COLOR CODED PER TABLE (SEE FIGURE 2) 1/ NOT FOR NAVY USE. RESTRICTED TO AIR FORCE SPACE APPLICATIONS ONLY. 2/ W FINISH IS NOT FOR USE IN SPACE APPLICATION. 3. QUALIFICATION: SEE AS850
32、49, CATEGORY 3A. THE AS85049/26-2 CRIMP RING SHALL BE QUALIFIED AND SUPPLIED WITH THE AS85049/26-1 CONNECTOR ACCESSORY. FIGURE 2 WILL REQUIRE EXAMINATION OF PRODUCT ONLY. 4. PART NUMBER: SEE EXAMPLE BELOW: FOR FIGURE 1: FOR FIGURE 2: Copyright SAE International Provided by IHS under license with SAE
33、Licensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NON-ENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3A (FOR MIL-DTL-5015 CRI
34、MP, MIL-DTL-26482 SERIES 2, AS81703 SERIES 3 AND MIL-DTL-83723 SERIES III CONNECTORS) AS85049/26 SHEET 6 OF 6 REV. A FOR FIGURE 3: 5. SUPERSESSION DATA: NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNIN
35、G CADMIUMS USE. 1. THE CHANGE BAR ( I ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICALREVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:42 MSTNo reproduction or networking permitted without license from IHS -,-,-