《SAE-AS-9230-1998-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-9230-1998-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS9230 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS9230 ISSUED 1998-08 R
3、EAFFIRMED 2007-06 BRACKET, ANGLE, 90 .190 x .312 BOLT PREPARED BY COMMITTEE E-25PROCUREMENT SPECIFICATION: NONE FEDERAL SUPPLY CLASS 5340 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS9230C AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT IN
4、TO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS9230C. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE P
5、ROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT T
6、HE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PROD
7、UCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval
8、system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServic
9、esae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:23:04 MSTNo reproduction or networking permitted without license from IHS -,-,- BRACKET, ANGLE, 90 .190 x .312 BOLT AEROS
10、PACE STANDARD AS9230 SHEET 2 OF 3 AS9230 TABLE I. DASH NUMBERS AND DIMENSIONS. INACTIVE FOR DESIGN AFTER 22 NOVEMBER 1966. USE MS9602. INTERCHANGEABILITY RELATIONSHIP: MS9230 INDIVIDUAL PART NUMBERS MAY BE REPLACED BY ONE OR MORE PART NUMBERS OF MS9602 SELECTED WITHIN THE SLOTTED HOLE DIMENSIONAL RA
11、NGE OF THE SUPERSEDED STANDARD. THE INACTIVATED MS9230 PARTS SHALL NOT BE USED TO REPLACE THE SUPERSEDING MS9602 PARTS. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:23:04 MSTNo reproduction or networking permit
12、ted without license from IHS -,-,- BRACKET, ANGLE, 90 .190 x .312 BOLT AEROSPACE STANDARD AS9230 SHEET 3 OF 3 AS9230 REQUIREMENTS: 1.MATERIAL. CORROSION RESISTANT STEEL IN ACCORDANCE WITH AMS 5504. 2.HEAT TREATMENT AND CLEANING. HEAT TREATMENT AND CLEANING IN ACCORDANCE WITH AMS 2550. 3.HARDNESS. 30
13、-38 HRC. 4.DIMENSIONING AND TOLERANCING. DIMENSIONING AND TOLERANCING SHALL BE IN ACCORDANCE WITH ANSI Y14.5M. 5.TOLERANCES. UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE FOR LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 2. 6.PART NUMBER. THE PART NUMBER SHALL CONSIST OF THE BASIC MS NUMBER FOLLOWED
14、BY A DASH NUMBER FROM TABLE I. EXAMPLE: MS9230-02 INDICATES - BRACKET, 90 ANGLE, LENGTH A, .562; LENGTH B, .625. NOTES: 1.ALL DIMENSIONS ARE IN INCHES. 2.DO NOT USE UNASSIGNED DASH NUMBERS. 3.REMOVE BURRS AND BREAK SHARP EDGES. 4.IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE R
15、EFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 5.REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS) SPECIFIED IN THE SOLICITATION, FORM A PART OF THIS STANDARD TO
16、THE EXTENT SPECIFIED HEREIN. 6.AS AND AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERS, INC. PUBLICATIONS. 7.THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:23:04 MSTNo reproduction or networking permitted without license from IHS -,-,-