《SAE-AS-9380-1998-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-9380-1998-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS9380 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS9380 ISSUED 1998-02 R
3、EAFFIRMED 2007-06 PLUG, EXPANSION - AMS 4003 PREPARED BY COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE PROPULSION FEDERAL SUPPLY CLASS 5340 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS9380 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT
4、 INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS9380. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE
5、 PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT
6、 THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. ANY MATERIAL RELATING TO QUALIFIED PRODUCT LISTS HAS NOT BEEN ADOPTED BY SAE. THIS MATERIAL WAS PART OF THE ORIGINAL MILITARY SPECIFICATION AND IS REPRINTED HERE FOR HISTORIC REFERENCE ONLY. RATION
7、ALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco
8、rding, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under
9、license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:13:46 MSTNo reproduction or networking permitted without license from IHS -,-,- PLUG, EXPANSION - AMS 4003 AEROSPACE STANDARD AS9380 SHEET 2 OF 3 AS9380 FIGURE 1 - PLUG TABLE 1 - DASH NUMBERS AND DIMENSIONS PART NUM
10、BER NOMINAL SIZE A DIA B .005 C .016 D .010 E 1 APPROX WEIGHT LB/100 MS9380-01 .188 .186-.189.025 .175-32 .01 MS9380-02 .250 .248-.252.032 .219-32 .02 MS9380-03 .312 .310-.315.063 .266.03332 .05 MS9380-04 .375 .372-.377.063 .406.03325 .07 MS9380-05 .438 .435-.440.063 .469.03325 .10 MS9380-06 .500 .4
11、97-.502.063 .531.03325 .13 MS9380-07 .562 .560-.565.063 .625.03325 .15 MS9380-08 .625 .622-.628.063 .750.03323 .19 MS9380-09 .688 .684-.690.063 .875.03323 .23 MS9380-10 .750 .747-.753.063 .938.03323 .28 MS9380-11 .812 .809-.815.0631.031.03323 .34 MS9380-12 .875 .872-.878.0801.094.04223 .48 MS9380-13
12、 .938 .934-.940.0801.156.04224 .55 MS9380-141.000 .997-1.003.0801.188.04224 .63 MS9380-151.0311.028-1.034.0801.250.04224 .68 MS9380-161.0621.059-1.065.0801.250.04224 .72 MS9380-171.1251.122-1.128.0801.375.04224 .80 MS9380-181.1881.184-1.190.0801.500.04224 .89 MS9380-191.2501.247-1.253.0801.625.04221
13、 .98 MS9380-201.3121.307-1.317.0801.750.042211.08 MS9380-211.3751.370-1.380.0801.812.042211.19 MS9380-221.4381.432-1.442.0802.000.042211.30 MS9380-231.5001.495-1.505.0802.125.042211.37 MS9380-241.5621.558-1.568.0802.250.042211.54 MS9380-251.6251.620-1.630.0802.375.042211.66 MS9380-261.6881.683-1.693
14、.0802.500.042191.79 MS9380-271.7501.745-1.755.0802.688.042191.93 MS9380-281.8121.807-1.817.0802.750.042192.06 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:13:46 MSTNo reproduction or networking permitted withou
15、t license from IHS -,-,- PLUG, EXPANSION - AMS 4003 AEROSPACE STANDARD AS9380 SHEET 3 OF 3 AS9380 1. MATERIAL: ALUMINUM AMS 4003. 2. MATERIAL CODE E40 PER AS 269. 3. FINISH: ANODIZE AMS 2470. 4. SURFACE ROUGHNESS: AS 291. 5. REMOVE BURRS AND SHARP EDGES. 6. DIMENSIONS IN INCHES. 7. DO NOT USE UNASSI
16、GNED PART NUMBERS. AS AND AMS ARE SAE PUBLICATIONS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. TABLE 1 - DIMENSIONS AND PART NUMBERS - CONTINUED PART NUMBER NOMINAL SIZE A DIA B .005 C .016 D .010 E 1 APPROX WEIGHT LB/100 MS9380-291.87
17、51.870-1.880.0802.875.04219 2.21 MS9380-301.9381.932-1.942.0803.094.04219 2.36 MS9380-312.0001.995-2.005.0803.188.04219 2.54 MS9380-322.0622.057-2.067.0803.188.04219 2.67 MS9380-332.1252.120-2.130.0803.250.04219 2.84 MS9380-342.2502.245-2.255.0803.562.04219 3.18 MS9380-352.3752.370-2.380.0803.875.04
18、219 3.54 MS9380-362.5002.495-2.505.0804.156.04217 3.92 MS9380-372.6252.620-2.630.0804.250.04217 4.33 MS9380-382.7502.745-2.755.0804.500.04217 4.74 MS9380-392.8752.870-2.880.0804.750.04217 5.17 MS9380-403.0002.995-3.005.0805.000.04217 5.64 MS9380-413.1883.182-3.192.0805.500.04217 6.35 MS9380-423.2503
19、.245-3.255.1405.500.0671710.60 MS9380-433.5003.495-3.505.1406.000.0671712.34 MS9380-443.7503.745-3.755.1406.000.0671714.18 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:13:46 MSTNo reproduction or networking permitted without license from IHS -,-,-