《SAE-AS-85049-36A-2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-85049-36A-2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3B (FOR MIL-C-27599 SERIES I AND MIL-DTL-38999 SERIES I AND II CONNECTORS) AS85049/36 Copyright 2007 SAE International All rights reserved. No part of this publication may b
2、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax
3、: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-05 REVISED 2007-06 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 REV. A FEDERAL SUPPLY CLASS 5935 AS85049/36 SHEET 1 OF 3 REV. A SAE Technical Standards Board Rules provide that: “This report is published
4、 by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical rep
5、ort at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE REVISED TO INCLUDE COMMENTS RECEIVED BY THE GOVERNMENT AND INDUSTRY USERS. UPDATED ALL REFERENCE SPECIFICATIONS. REMOVED GOVERNMENT JARGON AS A RESULT
6、 OF THE WORD-FOR-WORD CONVERSION. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS85049. FIGURE 1 - CONFIGURATIONS AND DIMENSIONS NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MAT
7、ERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. DIMENSIONS ARE IN INCHES. 2. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1.00 INCH = 25.4 MM. 3. METRIC EQUIVALENTS ARE IN PARENTHESIS. 4. STANDARD MINIMUM LENGTH IS 1.5 INCH .032 INCH (
8、38.1 MM .81 MM). SEE TABLE 3 FOR LONGER LENGTHS. 5. SEE TABLE 1 FOR MINIMUM AND MAXIMUM CLAMP SIZE AVAILABLE WITH EACH ACCESSORY SHELL SIZE. SEE TABLE 2 FOR CABLE RANGE FOR EACH CLAMP SIZE. 6. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE
9、TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 N
10、ot for Resale, 12/04/2007 20:04:33 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELD TERMINATION, CATEGORY 3B (FOR MIL-C-27599 SERIES I AND MIL-DTL-38999 SERIES I AND II CO
11、NNECTORS) AS85049/36 REV. A AS85049/36 SHEET 2 OF 3 REV. A TABLE 1 - ACCESSORY SHELL SIZE, CONNECTOR SHELL SIZE AND CLAMP SIZE TABLE 2 - CLAMP SIZE AND DIMENSIONS TABLE 3 - LENGTH CODE LENGTH IN INCHES .032 (.81) STANDARD1.50 (38.1) A2.50 (63.5) B3.50 (88.9) C 4.50 (114.3) Copyright SAE Internationa
12、l Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:04:33 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, STRAIGHT, SHIELD TERMINA
13、TION, CATEGORY 3B (FOR MIL-C-27599 SERIES I AND MIL-DTL-38999 SERIES I AND II CONNECTORS) AS85049/36 REV. A AS85049/36 SHEET 3 OF 3 REV. A REQUIREMENTS: DESIGN AND CONSTRUCTION: DIMENSIONS AND CONFIGURATION: SEE FIGURE 1 AND TABLES 1, 2, AND 3. INTERFACE DIMENSIONS SHALL CONFORM TO AS85049 FIGURE 2.
14、 MATERIAL: ACCESSORY COMPONENTS - ALUMINUM ALLOY IN ACCORDANCE WITH AS85049. CLAMP ASSEMBLY SCREWS - CORROSION RESISTANT STEEL IN ACCORDANCE WITH AS85049, PASSIVATED. FINISH: 1/ N - ELECTROLESS NICKEL 2/ W - CADMIUM OLIVE DRAB 1/ N NOT FOR NAVY USE, LIMITED TO SPACE APPLICATION FOR AIR FORCE. 2/ W I
15、S NOT FOR USE INSPACE APPLICATIONS. PART NUMBER: SEE EXAMPLE BELOW: SIMPLIFIED ASSEMBLY INSTRUCTIONS SHALL BE SHIPPED WITH THE UNIT PACKAGE. QUALIFICATION: SEE AS85049, CATEGORY 3B. SUPERSESSION DATA: Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:04:33 MSTNo reproduction or networking permitted without license from IHS -,-,-