《SAE-AS-9433B-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-9433B-2003-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、 AEROSPACE STANDARD BOLT, TEE HEAD, CHAMFERED - CRES, UNS S66286, 130 KSI MIN, .2500-28 UNJF-3A AS9433 ISSUED 1999-12 REVISED 2003-09 REAFFIRMED 2007-06 THIRD ANGLE PROJECTION CUSTODIAN: SAE E-25 REV. B FEDERAL SUPPLY CLASS 5306 AS9433 SHEET 1 OF 3 REV. B THE INITIAL SAE PUBLICATION OF THIS DOCUMENT
2、 WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9433, AMENDMENT 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO
3、 QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary,
4、 and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written
5、 comments and suggestions. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electroni
6、c, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE Int
7、ernational Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:52:50 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD BOLT, TEE HEAD, CHAMFERED - CRES, UNS S66286, 130 KSI MIN, .2500-28 UNJF-3A AS9433
8、REV. B AS9433 SHEET 2 OF 3 REV. B TABLE 1 - PART NUMBERS AND DIMENSIONS NOTES: 1. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS 5732 (UNS S66286). 2. PROCUREMENT SPECIFICATION: AS7478, EXCEPT HEAD SHALL BE UPSET. 3. HEAD TO SHANK FILET SHALL BE COLD ROLLED. 4. FLUORESCENT PARTICLE INSPECTION
9、PER ASTM E 1417, TYPE 1, SENSITIVITY LEVEL 2. 5. INCOMPLETE THREADS NOT TO ENTER FILLET. 6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 7. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 8. DIMENSIO
10、NING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS IN INCHES. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:52:50 MSTNo reproduction or networking permitted without license from IHS -,-,
11、- AEROSPACE STANDARD BOLT, TEE HEAD, CHAMFERED - CRES, UNS S66286, 130 KSI MIN, .2500-28 UNJF-3A AS9433 REV. B AS9433 SHEET 3 OF 3 REV. B 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL R
12、EVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AS AND AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERS, INC. PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN AMERICAN SOCIETY FOR TESTING AND MATERIALS PUBLICATION. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:52:50 MSTNo reproduction or networking permitted without license from IHS -,-,-