《SAE-AS-91711A-2003-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-91711A-2003-R2007.pdf（4页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 4 AS91711 REV. A THIRD ANGLE PROJECTION AEROSPACE STANDARD AS91711 REV. A
3、ISSUED 1999-12 REVISED 2003-10 REAFFIRMED 2007-06 (R) BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, BLACK OXIDE, STEEL, UNS G87400, 125 KSI MIN .3125-24 UNF-3A PREPARED BY SAE COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE & PROPULSION SYSTEMS FEDERAL SUPPLY CLASS 5306 THE
4、 INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9171A. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRA
5、CTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may
6、be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fa
7、x: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:21:18 MSTNo reproduction or networking permitted without license from IHS -,-,- BOLT
8、, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, BLACK OXIDE, STEEL, UNS G87400, 125 KSI MIN .3125-24 UNF-3A AEROSPACE STANDARD AS91711 SHEET 2 OF 4 AS91711 REV. A REV. A (R) Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 N
9、ot for Resale, 12/04/2007 20:21:18 MSTNo reproduction or networking permitted without license from IHS -,-,- BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, BLACK OXIDE, STEEL, UNS G87400, 125 KSI MIN .3125-24 UNF-3A AEROSPACE STANDARD AS91711 SHEET 3 OF 4 AS91711 REV. A REV.
10、 A (R) Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:21:18 MSTNo reproduction or networking permitted without license from IHS -,-,- BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, BLACK
11、OXIDE, STEEL, UNS G87400, 125 KSI MIN .3125-24 UNF-3A AEROSPACE STANDARD AS91711 SHEET 4 OF 4 AS91711 REV. A REV. A (R) Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:21:18 MSTNo reproduction or networking permitted without license from IHS -,-,-