《SAE-AS-85352-4-2002-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-85352-4-2002-R2007.pdf（2页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 2 AS85352/4 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS85352/4 ISSUED 200
3、2-02 REAFFIRMED 2007-12 INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT CUSTODIAN: SAE A-5 FEDERAL SUPPLY CLASS 6685 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-I-85352/4, NOTICE 1 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORM
4、ANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-I-85352/4, NOTICE 1. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER
5、 THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTIN
6、G AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIE
7、D PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p
8、hotocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provi
9、ded by IHS under license with SAELicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 02/16/2008 02:06:42 MSTNo reproduction or networking permitted without license from IHS -,-,- INFLATOR ASSEMBLY DUAL CHUCK STEM GAGE KIT AEROSPACE STANDARD AS85352/4 SHEET 2 OF 2 AS85352/4 THIS SPECIF
10、ICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE. THE COMPLETE REQUIREMENTS FOR PROCURING THE DUAL CHUCK STEM GAGES DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE IN EFFECT OF SPECIFICATION MIL-I-85352. REQUIREMENTS: DUAL CHUCK STEM GAGE:
11、 THE DUAL CHUCK STEM GAGE SHALL CONSIST OF THE GAGE SHOWN WITH A GAGE ELEMENT CONFORMING TO M85352/3-1 OR M85352/3-2 AS SPECIFIED BY THE PART NUMBER. PART NUMBER: PART NUMBERS SHALL CONSIST OF THE FOLLOWING: (IN SEQUENCE) 1.THE LETTER “M” 2.THE GENERAL SPECIFICATION NUMBER 3.A SLASH, AND SLASH NUMBE
12、R OF THIS SPECIFICATION SHEET 4.A DASH, AND THE APPROPRIATE SIZE DASH NUMBERS FROM TABLE I Copyright SAE International Provided by IHS under license with SAELicensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 02/16/2008 02:06:42 MSTNo reproduction or networking permitted without license from IHS -,-,-