《SAE-AS-9354-1998-R2007.pdf》由会员分享，可在线阅读，更多相关《SAE-AS-9354-1998-R2007.pdf（3页珍藏版）》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 3 AS9354 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS9354 ISSUED 1998-02 R
3、EAFFIRMED 2007-06 CLAMP, LOOP - ALUMINUM, .265 HOLE PREPARED BY COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE PROPULSION FEDERAL SUPPLY CLASS 5340 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS9354 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO B
4、RING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS9354. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UN
5、DER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VO
6、TING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. ANY MATERIAL RELATING TO QUALIFIED PRODUCT LISTS HAS NOT BEEN ADOPTED BY SAE. THIS MATERIAL WAS PART OF THE ORIGINAL MILITARY SPECIFICATION AND IS REPRINTED HERE FOR HISTORIC REFERENCE ONLY.
7、 RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin
8、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS
9、 under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:22:23 MSTNo reproduction or networking permitted without license from IHS -,-,- CLAMP, LOOP - ALUMINUM, .265 HOLE AEROSPACE STANDARD AS9354 SHEET 2 OF 3 AS9354 FIGURE 1 - CLAMP, LOOP TABLE 1 - DIMENSIONS AND
10、PART NUMBERS PART NO. NON TUBE OD A DIA BASIC B .005 C .010D E REF F RAD .016 APPROX WEIGHT LB/EA MS9354-01 .125 .125.031 .360.062-.078.000.062.002 MS9354-02 .188 .188.031 .423.062-.078.031.062.002 MS9354-03 .250 .250.031 .457.062-.078.062.062.003 MS9354-04 .312 .312.031 .498.062-.078.094.062.003 MS
11、9354-05 .375 .375.031 .529.062-.078.125.062.003 MS9354-06 .438 .438.031 .560.062-.078.156.062.004 MS9354-07 .500 .500.031 .592.062-.078.188.062.004 MS9354-08 .562 .562.031 .623.062-.078.219.062.004 MS9354-09 .625 .625.031 .654.062-.078.250.062.005 MS9354-10 .688 .688.051 .752.062-.078.281.109.008 MS
12、9354-11 .750 .750.051 .783.062-.078.312.109.009 MS9354-12 .812 .812.051 .814.062-.078.344.109.011 MS9354-13 .875 .875.051 .845.062-.078.375.109.011 MS9354-14 .938 .938.051 .877.062-.078.406.109.011 MS9354-151.0001.000.051 .908.062-.078.438.109.011 MS9354-161.0621.062.051 .939.062-.078.469.109.012 MS
13、9354-171.1251.125.051 .970.062-.078.500.109.012 MS9354-181.1881.188.0511.002.062-.078.531.109.013 MS9354-191.2501.250.0641.062.094-.110.531.125.017 MS9354-201.3121.312.0641.093.094-.110.562.125.018 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/59139770
14、01 Not for Resale, 12/04/2007 19:22:23 MSTNo reproduction or networking permitted without license from IHS -,-,- CLAMP, LOOP - ALUMINUM, .265 HOLE AEROSPACE STANDARD AS9354 SHEET 3 OF 3 AS9354 MATERIAL: ALUMINUM AMS 4041. REMOVE BURRS AND SHARP EDGES. DIMENSIONS IN INCHES. CLAMP SHALL BE FORMED AS S
15、HOWN. DIMENSION “D” SHALL FALL WITHIN THE SPECIFIED LIMITS WHEN CLAMP IS ASSEMBLED ON A BAR, THE DIAMETER OF WHICH IS EQUAL TO THE NOMINAL TUBE OD WITHIN .001. HOLES SHALL BE IN ALIGNMENT WITHIN .010 AND CLAMP SHALL BE FLAT WITHIN .010 THRU CLAMP WIDTH WHEN ASSEMBLED ON TEST BAR. IN THE FREE POSITIO
16、N, CLAMP MAY SPRING OPEN PROVIDED THE ABOVE CONDITIONS ARE MET. DO NOT USE UNASSIGNED PART NUMBERS. AS AND AMS ARE SAE PUBLICATIONS. THIS MILITARY STANDARD WAS DEVELOPED COOPERATIVELY WITH THE MILITARY SERVICES BY THE SAE AEROSPACE PROPULSION DIVISON. TABLE 1 - DIMENSIONS AND PART NUMBERS - CONTINUE
17、D PART NO. NON TUBE OD A DIA BASIC B .005 C .010D E REF F RAD .016 APPROX WEIGHT LB/EA MS9354-211.3751.375.0641.125.094-.110.594.125.018 MS9354-221.4381.438.0641.156.094-.110.625.125.019 MS9354-231.5001.500.0641.188.094-.110.656.125.019 MS9354-241.5621.562.0641.219.094-.110.688.125.020 MS9354-251.62
18、51.625.0641.250.094-.110.719.125.021 MS9354-261.6881.688.0641.281.094-.125.750.125.021 MS9354-271.7501.750.0641.312.094-.125.781.125.022 MS9354-281.8121.812.0641.344.094-.125.812.125.023 MS9354-291.8751.875.0641.375.094-.125.844.125.023 MS9354-301.9381.938.0641.406.094-.125.875.125.024 MS9354-312.0002.000.0641.438.094-.125.906.125.024 Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 19:22:23 MSTNo reproduction or networking permitted without license from IHS -,-,-