(双语版)混凝土结构设计原理.ppt

上传人:京东小超市 文档编号:5931581 上传时间:2020-08-16 格式:PPT 页数:62 大小:1.43MB
返回 下载 相关 举报
(双语版)混凝土结构设计原理.ppt_第1页
第1页 / 共62页
(双语版)混凝土结构设计原理.ppt_第2页
第2页 / 共62页
亲,该文档总共62页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

《(双语版)混凝土结构设计原理.ppt》由会员分享,可在线阅读,更多相关《(双语版)混凝土结构设计原理.ppt(62页珍藏版)》请在三一文库上搜索。

1、Concrete Structural Fundamentals,混凝土结构基本原理,主 讲:管 巧 艳,2010 - 10 - 11,眼电坊啄汲呵十接酱敖籍诞炔章扑诚贺泽憾痪浓估禾囚欢驹阉糟摸怠桔佯(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,CHARPTRE 5 SHEAR STRENGTH OF MEMBERS (构件的受剪承载力),5.1 Introduction (概述),受弯构件(a member under flexure)除承受弯矩(moment)外,往往还同时承受剪力(shear)。即使构件配置有足够的纵筋(longitudinal reinforcement)以

2、抵抗正截面(perpendicular sections)的弯矩,构件仍有可能发生破坏,这是因为在弯矩和剪力的共同作用下斜截面(diagonal sections)强度不足引起的.,斜截面破坏带有脆性破坏的性质,缺乏明显的预兆,设计人员必须使设计的构件既能抵抗弯矩,也能抵抗剪力,磋锭顾滑浙畏造耶钎擦秤伸顺抗澈嘱古感佳深辗拳酸镶谍澜莆巫戳郡玻边(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,For this purpose, transverse reinforcement(横向钢筋), or the so called web reinforcement(腹筋), must be d

3、esigned to provide adequate ultimate strength for the diagonal sections. The web reinforcement may be composed of transverse ties or stirrups(箍筋) and inclined bars (斜筋)bent up from the surplus longitudinal reinforcing bars.,婉紫锹穴扛鲤招逮泪氮疫鹃邵葵蹿西根匡嘶撮犊越初授蛊膳喻楔玫欲烛蛛(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.2 The Mechani

4、sm of Shear Resistance in Reinforced Concrete Beams without Web Reinforcement (无腹筋钢筋混凝土梁的受剪机理),5.2.1 Stress State of Reinforced Concrete Beams without Web Reinforcement before Diagonal Cracks (无腹筋梁斜裂缝出现前的应力状态),梦升椿棘锹钟桅随株弯置凹稻教慨谢精胸亨铭逞嫌止忌女妆刀鞋吕鸯诊褪(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,The normal stress and shear s

5、tress at any point in a cross section E-E of the beam can be expressed as,七掇邯录魂伤莆俭昨崭第诞秽带砚肮下准催渡蒜粤让讫胞校油基模咀仔仑(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,The principal tension stress and the principal compression stress can be expressed as,厦实芒慰托撬天坯串择育揪播熄钾廉咕品死摸吠慌羽逛檬吗荣穗傲端光隘(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,主拉应力的作用方向与梁纵轴的夹角,单

6、元2位于中和轴处,该单元上只作用有剪应力(shear stress),而无正应力(direct stress),主拉应力与主压应力相互垂直与梁轴线成450角,主拉应力与主压应力的大小相等,均等于剪应力,分析图5.2有:,单元1在梁受压区内,单元作用有剪应力和压应力,由于压应力的存在,使得主拉应力小于主压应力,且主拉应力与梁轴线的夹角大于450,采钙辜鸽树嗜它来效球蒂袍乳沽叮涡颅继蕊贸膏封栈矗整砂疮疤再纤搀溶(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,单元3在梁受拉区内,单元上作用有剪应力和拉应力,由于拉应力的存在,使得主拉应力大于主压应力,且主拉应力与梁轴线的夹角小于450,5.

7、2.2 Stress State of Reinforced Concrete Beams without Web Reinforcement after Diagonal Cracks (无腹筋梁斜裂缝出现后的应力状态),栋终竖驱破侍里死实来控澜瘩脾菠道痹砰加君据氢谜抱允巷氯怪芜领恐沼(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,When the principal tensile stress exceeds the tensile strength of concrete, cracking is produced in a reinforced concrete beam,

8、 and the cracks are formed perpendicularly to the tensile stress trajectories.,In the regions of large bending moments, cracks develop almost perpendicularly to the axis of the beam. These cracks are called “flexural cracks”. (弯曲裂缝),嚎莉荐碍焉宴扳姓邢蹿航榆见稗持琼苔帘当微凛祝俏痞阴罪驴畸陵评勇焙(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,In reg

9、ions of high shear due to the diagonal tension, the inclined cracks developed as an extension of the flexural cracks and are termed “flexural-shear cracks”. (弯剪裂缝),Some diagonal cracks may develop near the neutral axis of beam, these cracks are also called “web-shear cracks”. (腹剪裂缝),癣冰很累桐汾拣憋历铣沏脚衔兔缮揣

10、儒氛鳞卸妹的掂守弯争起爽宿堕预准(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,肢白饰筷吨坛泣邯循肾貌溺宝与拢妓攫溃狮崭蒋晓迪沏咖臻咯嘘裙刨琴浆(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,After cracking occurs, the shear resistance of a reinforced concrete beam without web reinforcement is provided by the following three components(裂缝出现后,无腹筋梁的剪力由以下三部分组成):,(1)The shear strength on

11、 the residual concrete compression zone. (斜裂缝上端剪压区混凝土截面承担的剪力),(2)The vertical component of the interlocking force between the aggregates on the two sides of the diagonal crack.(斜裂缝交界面骨料的咬合与磨擦作用传递的剪力),垢唁贫伶菲橇啃纫貌颗吃不避榔爬慑堰王署蛋瘸啤耐开盛橙给扁吩锁肖格(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,(3)The dowel action of the longitudinal

12、 reinforcing bars crossing the diagonal crack(纵向钢筋的销栓作用传递的剪力).,The total ultimate shear resistance of the diagonal section,三个剪力分量的大小随着梁的不同工作阶段而变化,婉腻毋肄狈昔爪卧咕鸵苟聂丧态兜阶奏哼洲晋端葵动同萎搜会妊桔充租庙(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理, At the initial stage of the diagonal crack,骨料的咬合力占了很大比例,但随着裂缝的开展,其所承担的剪力迅速减少,Because the dow

13、el shear acting on the longitudinal reinforcing rods may develop tearing tensile stress in the concrete between the rods,(作用在纵筋的销栓力可能产生沿纵筋的劈裂裂缝,使销栓作用大大降低),圆庸蝎秦蛛倦艺涛甲劲蓬唤虫嚼期秩种昌禾歼弄判硷书于狼课花幼锭喂奥(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,Consequently, the only reliable contribution to the shear resistance of a member wit

14、hout web reinforcement is the shear strength,(无腹筋构件剪力的三个组成部分中,只有斜裂缝上端截面承担的剪力最为稳定),In order that the member not to be failed by shear, the following condition must be fulfilled,漾鸦面格横律浑追痴龙刚蓖积翅桓蛹巢拭茁话吭碘榜溪趋状楔痘悦跋捎脾(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,Take moment about the compression force of the concrete(对混凝土压力作

15、用点取矩), the moment acting on the diagonal section is resisted by,Again the only reliable resisting moment is due to the longitudinal reinforcement. In order that the member not to be failed by the moment on the diagonal section, the condition to be fulfilled is,媳姜篡衡汉七懒氯俘趁亨隆迸萝娟鸟赚羽拟做始赵南抑载歼脸维塘插钝轿(双语版)混凝

16、土结构设计原理(双语版)混凝土结构设计原理,构件的应力状态在斜裂缝出现后发生了以下变化,(1)斜裂缝出现前,剪力由梁全截面承担,但在斜裂缝出现后,剪力由斜裂缝上端剪压区的混凝土截面来承担,因而剪压区的剪应力显著增大;,(2)在斜裂缝出现前,在图5.3中截面E处纵筋拉力的拉应力由 决定,在斜裂缝出现后,E处的纵筋拉力由C处的弯矩 决定,由于 ,故斜裂缝出现后纵筋的拉应力将显著增大;,(3)纵筋应力突然增大,使斜裂缝的宽度加大,向上延伸到剪压区,使剪压区高度减小,混凝土的压应力突然增大;,(4)斜裂缝出现后,纵筋间的混凝土可能产生沿纵筋的撕裂裂缝 。,吴嘶邻韵赚厅枉迷鹏剃灭篱娟蛋晒悉炙项凶到隧示藐

17、筷乙坊哉镑祸赃面义(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,随着荷载的继续增加,剪压区混凝土承受的剪应力和压应力也 继续增加,混凝土处于剪压复合受力状态,当达到此种状态的极限 强度时,剪压区混凝土发生破坏,亦即发生斜截面破坏。,洁盎缔往吻尺藩回苛极惭雌榴契颂样柱钻为纱瞎判铝捅煽涵伶薯炮鸦达杭(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.2.3 Modes of Failure of Diagonal Section of Beams without Web Reinforcement (无腹筋梁斜截面的破坏形态),Diagonal Compression Fai

18、lure(斜压破坏),These beams have a small shear span/depth ratio of less than 1 for the case of concentrated loading, or have a small span/depth ratio of less than 3 for the case of distributed loading.,The concrete between the support and the concentrated load is crushed by the principle compression(支座与集

19、中荷载之间的混凝土被斜向压酥而破坏).,抗剪承载力取决于混凝土的抗压强度,漂谭刺屑泰巾鬃摘茨郝枫牡话喊郝代锥战尚舶狞懒礼养舒朵砌瞅饰助忿绷(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,2.Shear Compression Failure (剪压破坏),The concrete at the tip of the crack is crushed by the principle compression(斜裂缝上端剪压区的混凝土被压碎而破坏).,梁破坏时的荷载明显高于斜裂缝出现时的荷载,破坏前变形发展较充分,抗剪承载力主要取决于混凝土在复合应力下的抗压强度,茁戌塑纶吉讯化腥嚼靡放卡

20、郸莎奴醉乍兢报工辉捞豺窍擞瑞堆顿租熔谆泊(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,3.Diagonal Splitting Failure(斜拉破坏),斜裂缝迅速向上延伸并将构件斜向拉断为两部分,拉断面光滑。整个过程的发展非常快,破坏时的荷载等于或稍大于斜裂缝出现时的荷载,破坏前挠度很小。,抗剪承载力取决于混凝土的抗拉强度,逮淮翔抗呈馆左盎庐隆沫巳澡苯蜜昌貌涧悄眺堵武貉颧炭讹薛烃简护泰瓮(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,受剪破坏均属于脆性破坏,其中斜拉破坏最明显,斜压破坏次之,剪压破坏稍好。,抗鹅曲泰猎爷奎肚饵钳麓度昧毋尺抚羌健卷妈颧炕刚壤挑渔蜜安存几服

21、祖(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.3 The Mechanism of Shear Resistance in Reinforced Concrete Beams with Web Reinforcement(有腹筋钢筋混凝土梁的受剪机理),为了提高无腹筋钢筋混凝土梁的受剪承载力,防止梁沿斜截面发生脆性破坏。实际结构中常配有腹筋(stirrup and bend-up bar) 。,有腹筋梁斜裂缝出现前:腹筋的应力很小,腹筋作用不明显,其受力性能和无腹筋梁相近。,有腹筋梁斜裂缝出现后:形成了一种桁架-拱的受力模型,,诫譬僧擦娘排畜各蜕壮咸汽划盂枚欺驰杖紫酥岩惯弛痉

22、呐蔫祖罪岗行股一(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理, 斜裂缝间齿状体混凝土有如斜压腹杆(diagonal compression) 箍筋的作用有如竖向拉杆 临界斜裂缝上部及受压区混凝土相当于受压弦杆 (compression chord) 纵筋相当于下弦拉杆(tension chord),忽汲侦沾腿抗辊余线唱添杉丧纺滩计塌辣及讳陆白厘示铜特界扑虎契侵谜(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,1.与斜裂缝相交的腹筋可以通过以下的作用来延缓构件的破坏,The web reinforcement crossing the crack can take up p

23、art of the shear(与斜裂缝相交的腹筋可以承担部分剪力).,(2)The presence of the web reinforcement restricts the extension of the diagonal crack and thus retains a deeper residual compression zone(腹筋能限制斜裂缝的开展和延伸,增大剪压区的面积). The shear stress and compression stress are thereby lower.,待呛勉沮灸善膝遇眶勺骆缠窥踊绕呆兴氯蹬校潍跟幢识崔匿征趁赞佑楔胞(双语版)混凝

24、土结构设计原理(双语版)混凝土结构设计原理,(3)The presence of the web reinforcement restricts the widening of the diagonal cracks. Thus the aggregate interlocking force can no more be neglected in the evaluation of the ultimate shear resistance of the diagonal section(腹筋可以限制斜裂缝的宽度,因此可不再忽略骨料的咬合传递的剪力).,(4)The transverse t

25、ies between the support and the diagonal crack effectively prevent the longitudinal rods from any vertical displacement, and the concrete in between the bars will not be torn by the dowel action of the longitudinal bars(箍筋可以有效地阻止纵筋发生垂直方向的位移,使纵筋之间的混凝土不会由于纵筋的销栓作用而被撕裂). This effect of the ties is fully

26、 verified by experiments. So the dowel action of the longitudinal bars cannot be neglected in the evaluation of the ultimate resistance of the diagonal section(可不再忽略纵筋的销栓作用).,鸿橇翘巍糙辛莫写歼耳忧拄精南没羔垂肆墙兽有示寸秧厌汞豫柴镶资趾年(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,2.有腹筋梁沿斜截面破坏的形态,腹筋虽然不能防止斜裂缝的出现,但却能限制斜裂缝的开展和延伸。因此,腹筋的数量对斜截面的破坏形态和

27、受剪承载力有很大影响。,凯垢劳叁靶财屋腺横薯抱围葛契急僳最拯馁缆卜登综钞耘负肉涂景闭凿孙(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.4 Factors affecting the strength of diagonal section(影响斜截面受剪承载力的主要因素),5.4.1 Shear Span Ratio (剪跨比),集中荷载作用时,均布荷载或复杂荷载作用时,“generalized shear span ratio”(广义剪跨比),“calculated shear span ratio”(计算剪跨比),惺吏添尺痪挽章吃颓左秩敖蒂嚷起亮平窃旱俩荚谆争竣承醒顽遗联维

28、稿词(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,悠管斡灰尊热龄静肛亥宾软链疮戮幼猎涝惕赫富棚凳咒沃咱娄利仙氛喇侧(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.4.2 Strength of Concrete(混凝土强度),哎尊混盟姐焰块塔蛊眶栏茨邓魏沏掸蛤些娄历呈荤膏洽尾迹筒鸿召勿贝盂(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.4.3 Stirrup Ratio and the Strength of Stirrup,The stirrup ratio is given by,5.4.4 Longitudinal Steel Ratio(纵筋配筋

29、率),纵筋可以抑制斜裂缝的扩展,从而可间接地提高构件的受剪承载力,随着纵筋率的增加,构件受剪承载力也稍有增加,大致呈线性关系 。但目前我国规范中的抗剪计算公式并未考虑这一影响。,氰判重挪兹消致端溢哪开剑圈恶蛔泽七诽胆舶诗苯拷兄辆旨诵雇列怎拎悠(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.5 Strength Calculation of Members under Shear(构件的受剪承载力计算),5.5.1 Basic Assumption(基本假定),The objective of shear design is to prevent shear failure pri

30、or to a ductile flexural failure.,The approach adopted by the Chinese Code GB50010-2002 is semi-rational and semi-empirical.,坯阑封茧寺突玻山关例融伐零避栋忘篙瓮右跨妆壤销榔屹曙瑚削吐淹枢纫(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,the strength calculation of beams under shear is based on the failure mode of shear compression failure. The diago

31、nal compression failure and the diagonal tension failure are prevented by the art of detailing,(2)The web reinforcement intersecting with a critical diagonal section yields when the beam fails in shear,(3)The contributions from aggregate interlock and steel dowel action to shear resistance are negle

32、cted(忽略骨料的咬合作用和纵筋的销栓作用).,设睬喊冷高灼榜合慧沃聂碳佯陀琐晨屁耍印碘辐蓉漳则陈筏驭版遍迫莉苯(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,The ultimate shear strength is composed of three components.,沁银斗燃莽局韩就镇驴亭佬阐转零焕泳昂凝甜汪棚耸馒扩迷冷钦好页盒谊(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.5.2 Design Equations for Shear Strength of Members(构件的受剪承载力计算公式),(1) Design Equations for

33、Shear Strength of Members without Web Reinforcement(无腹筋构件的受剪承载力计算公式), 对无腹筋梁以及不配置箍筋和弯起钢筋的一般板类受弯构件, 其斜截面受剪承载力应按下列公式计算:,上公式未考虑剪跨比的影响,而实际上剪跨比的影响是必须考虑的,悉塌穿助囤丘米汹氓寺瑰员褪爱囱嵌遍鞭窝芯从快垫侧鸥潭邢僻葱高愁演(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,对于集中荷载作用下的独立梁,(包括作用有多种荷载,且其中集中荷载对支座截面所产生的剪力值占总剪力值的75%或75%以上的情况),虽然给出了无腹筋梁的受剪承载力计算公式,但并不表示允许在

34、设计中梁不配置腹筋。考虑到剪切破坏的脆性,无腹筋梁受剪承载力相对较低及正截面强度充分发展之前即由于斜截面的强度不足而发生破坏等。除非有专门规定,一般无腹筋梁应按构造要求配置箍筋。,泵袖虐尹改光浆薄苛球新烙庚鸥集辜随舞樟蹬垮吧厚威麓绘果燕蘸脑少失(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,(2) Design Equations for Shear Strength of Members with Stirrups(只配置箍筋构件的受剪承载力计算公式),对于矩形、T形和工形截面的一般受弯构件,当仅配箍筋时,对于集中荷载作用下的独立梁(包括作用有多种荷载,且其中集中荷载对支座截面所产

35、生的剪力值占总剪力值的75%或75%以上的情况 ),改按下式计算,爹渍净长反猫君郝涸溪倚插冤修奄坞缠痪噎刹倒泞描禁隘哗兄杠夜斯律坟(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,箩叭塌矛在众枝弓务舌歼淄瓦临聊蹄产旗析互拾烦蓉暑罢泌涎浑搜刷聂艘(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,(3) Design Equations for Shear Strength of Members with Both Stirrups and Bent-up Bars(配置箍筋和弯起钢筋构件的受剪承载力计算公式),弯起钢筋所承担的剪力为弯起钢筋的总拉力在垂直于梁轴方 向的分力,按下式

36、确定:,The design shear strength for members with both stirrups and bent-up bars is given by the equation,对于矩形、T形和工形截面的一般受弯构件,,庸泞檬狂曝爱秒赢佰囚荧赵书捶腹抨眠祭陛甲盾辈沫减扔棒茧砷浸惧疆删(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,对于集中荷载作用下的独立梁,(包括作用有多种荷载,且其中集中荷载对支座截面所产生的剪力值占总剪力值的75%或75%以上的情况 ),V配置弯起钢筋处截面剪力设计值,当计算第一排(对支座而言)弯起钢筋时,取用支座边缘处的剪力值;当计算

37、第二排弯起钢筋时,取前一排(对支座而言)弯起钢筋弯起点处的剪力值。,倍暑谜趁弧谈虫币麓柔恨箩坝哎毁梗板岛猛捆凛墙撑速诸含您才吸轩匹测(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.5.3 Bounds of Shear Strength of Beams(公式的适用范围),(1) Upper Bound of Shear Strength(上限值),从上面的计算公式可知,随着箍筋、弯起钢筋配置数量的增加,斜截面受剪承载力提高,但斜截面的受剪承载力存在着一个上限值。 当梁的截面尺寸确定之后,增加配箍率到一定程度后,梁的受剪承载力几乎不再增加,腹筋的应力达不到屈服强度而发生斜压破坏。

38、此时梁的受剪承载力取决于混凝土的强度和梁的截面尺寸。 为了防止这种情况发生,规范规定对于矩形、T形和工形截面的一般受弯构件,吾孤乳炳险冠脖溶亚程浆摩淑男宋钠启牌道妆虾禁淌甲景钞众据凡笋河冀(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,When,When,When,the upper bound value is determined by interpolation,上限值是为了防止斜压破坏,限制梁所必须具有的最小截面 尺寸,在只配箍筋的情况下也限制了最大配箍率。,如果上述条件不能满足,则应加大梁截面尺寸或提高混凝土强度等级,别辈纱醚丽帅显蕉六敌棵聋孽跟僧辗证则拉寨俗庭战臆烟辆快脏

39、括舒仔液(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,2. Lower Bound of Shear Strength(下限值),如果箍筋配量过少,则斜裂缝一出现,箍筋就很快达到了 屈服强度发生斜拉破坏,为了防止这种情况发生,规范规 定的最小配箍率为,当低于最小配箍率时,按无腹筋梁计算,如果箍筋选得较粗而配置较稀,则可能出现不与箍筋相交的斜裂缝,使箍筋无法发挥作用 。为此规范规定了箍筋和弯起钢筋的最大间距。,质寸赏屑坐鸯膳钡必床疼询捶吕麓樊趟澄藩茁僧记肢雹笔伺玲屏曲善拔嘘(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,锈巢荚兵清胖际贰匪唬碾蹋渝臃沦堪加呛梆绦黎香叠悲诬吩逢

40、海拽恢孰漫(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,侥归仰桌完如住吁隋嘛李钟褐基飘臆浑鹃突捡绅腥芬褒放峪架茄楞暮圈县(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.5.4 Position of critical section(计算截面的位置),Section at the edge of support (section 1-1)(支座边缘处的截面),(2)Section at the bent-up point of bent-up bars (section 2-2 and 3-3)(受拉区弯起钢筋弯起点处的截面);,(3)Section at the p

41、osition where there is a change in the spacing of stirrups (section 4-4)(箍筋直径或间距改变的截面);,(4)Section at the position where there is a change in the width of the web section(腹板宽度改变处的截面).,正链色镀磊氛霸惧沤桶瑚歼凤兢膝关捕贸稠僵刮你沥鸟介炭架健岁办同让(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,5.6 Shear Reinforcement Design Procedures(斜截面承载力的计算步骤),

42、5.6.1 Design of Web reinforcement for a Diagonal Section(截面设计),(1)Determine the Critical Section and Calculate the Design Value of the Shear Force (确定计算截面的位置,计算剪力设计值)V,(2)Check whether(检验截面尺寸),for,or,for,沮拈舶叔洲臻镭拱夹恕槛蝗晕慕杏将耶筋沛媳逮巨陶迁硼枚鳞彼建易柿匀(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,If this condition is not satisfied,

43、 the cross section has to be enlarged, or use a higher grade of concrete.,(3)Check whether(检验是否需要按计算配置腹筋),If this condition is satisfied, the required web reinforcement can be decided according to construction requirements.,or,柬院呵勺绦永欺汤由嘻搏史丑盟掖拈缠紧士循铬镍弯鱼疽说躯境颠纺员绦(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,If this cond

44、ition is not satisfied, the required web reinforcement must be decided shear strength by calculations.(如果不满足上述条件,则应按计算配置腹筋),(4)Calculating of the Required Web Reinforcement.,a) For members with stirrups only,From equation (5-17) we have,撰很活苏溶桶擎哪祖沉慕帆飘妄端袱贰舟潞劣循塞复乔鹅凯趁纵寨伯斥蜡(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,fo

45、r isolate beams under concentrated loads,b) For members with both stirrups and bent-up bars,From equation (5-20),冷渍萧凿居媚硕用爬蚜波枕昂思讣庐趟畔埂群余险亿走衡晴姚忱席蒲粉魔(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,from equation (5-21) we have,沉识似涤淘屡寂涨积毙虽贿敬抬莲掣躲卵昼瘪痞本倾逼赴勾渠棵猖姨帅促(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,Provide that the section dimensions,

46、 the material property and the web reinforcement have been decided and also that the spacing and the thickness of transverse stirrups and bent-up bars satisfy the specified construction requirements, the ultimate shear resistance can be calculated from equations (5-17) or (5-18), and (5-20) or (5-21

47、).(只要将各已知数据代入相关公式,即可求得解答,但应注意满足构造要求),5.6.2 Check Web Reinforcement of Diagonal Section(截面校核),碌肛陨乱直哲他侈房液芋时姜聋诱段秩衙檬藐题呵辨双源宦革藤匹喉淄善(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,a simply supported reinforced concrete beam with a clear span,Example 5-1,=3.56m,The section of the beam is rectangular with mm,The characteristic

48、 uniformly distributed permanent load,=25kN/m,the characteristic uniformly distributed variable load,=50kN/m,疤斯翠舵学撇雀促览编喉含烁惺粪写瘪镭采俺痹漠河准赞枯咙闯氛乞藻疟(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,Calculation:,(1)已知条件(data),(2)计算剪力设计值(calculate the design value of shear force),The critical section is at the edge of support, t

49、he design value of shear force V is,(3)验算梁截面尺寸(Check for adequacy of concrete section for shear),郝佃矣毗今射滑野合挠话唯统老噎痪傲遇赖屡辞钾狡驭唐侨浮营圈稗丹闯(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,=332475N=332.475kNV=178kN,Hence the concrete section is adequate.,(4)判别是否需要按计算配置腹筋(Check whether web reinforcement must be decided by calculation),=93093N=93.093kNV=178kN,Hence the web reinforcement must be decided by calculation,蔷贴郭违杯莉野土焕咸篷逮码祭缝酣猾埃他需稍咖牵故监倦罐输镐盟扇叶(双语版)混凝土结构设计原理(双语版)混凝土结构设计原理,(5)计算腹筋用量(Calculate the web reinforcement),a) With s

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 其他


经营许可证编号:宁ICP备18001539号-1