《51010-1-7a0_s26_01-s26_05.doc》由会员分享，可在线阅读，更多相关《51010-1-7a0_s26_01-s26_05.doc（95页珍藏版）》请在三一文库上搜索。
1、.26Testing of layer 3 functionsRef.: 3GPPTS04.08 / 3GPPTS24.008 / 3GPPTS44.018NOTE:The tests on functioning of the elementary procedures in the MS are grouped as the description of those procedures in 3GPPTS04.08 / 3GPPTS24.008 / 3GPPTS44.018. However, the test procedures are carried out in an order
2、 which is more logic for the purpose of testing.26.1Default conditions and structured sequence of tests26.1.1Default test conditions during layer 3 testsDuring tests in clause 26 the following default test conditions shall apply if not otherwise stated within the test description. In the table below
3、, decimal values are normally used. Sometimes a hexadecimal value, indicated with a H, or a binary value, indicated with a B is given.GSM900DCS1800General signalling conditions for all carriersCipheringyesyesGeneral RF-conditions for all carriersFrequency hopping modeNon-hoppingNon-hoppingPropagatio
4、n profileStaticStaticDownlink Input Level63 dBmVemf( )63 dBmVemf( )Uplink output powerMinimum accordingMinimum accordingto MS power classto MS power classServing cell, BCCH/CCCH carrierChannel ARFCN20590Alternative channels40 or 60690 or 830Serving cell, Traffic channel, SDCCHChannel ARFCN30650Alter
5、native channels50 or 70750 or 850Power Control Indicator00Neighbouring cells BCCH/CCCH carriersChannel ARFCN10, 80, 90, 100, 110, 120520, 600, 700, 780, 810, 870Alternative channels15, 85, 95, 105, 115, 122530, 610, 710, 790, 820, 880Input level53 dBmVemf( )53 dBmVemf( )Network dependent parametersC
6、ell identity0001H0001HMobile country code, MCC001 (decimal)001 (decimal)Mobile network code, MNC01 (decimal)01 (decimal)Location area code, LAC0001H0001HFrequency ListBit Map 0Range 512BCCH allocation sequence00number(BA_IND)Cell Channel DescriptorBit Map 0Range 512PLMN colour code, NCC11BS colour c
7、ode, BCC55SMS Cell Broadcastnot activenot activeDTXMS must not useMS must not useIMSI Attach-detachMS shall not applyMS shall not applyCCCH_CONF1 basic physical channel for1 basic physical channel forCCCH combined with SDCCHCCCH combined with SDCCHBS_AG_BLKS_RES0 blocks reserved0 blocks reservedBS_P
8、A_MFRMS5 paging subgroups5 paging subgroupsGSM900DCS1800CELL_BAR_ACCESS(not barred)(not barred)Call-reestablishment (RE)(allowed)(allowed)Emergency Call allowedallowedsameAccess Control Classallowedsame(AC) (0.9, 11.15)Network dependent timersRadio_Link_Time-out88T3212 PeriodicInfiniteInfiniteupdati
9、ng in decihoursAccess control parametersMax retrans11Tx-integer, nr. of slots55CELL_RESELECT_HYSTERESIS12 dB12 dBMS_TXPWR_MAX_CCHminimum levelminimum levelRXLEV_ACCESS_MINminimumminimumNECINew establishment causessameare not supportedACS (ADDITIONAL RESELECTIONNo additional cell parameterssamePARAM
10、IND)are present in SI messages7 and 8C2 parametersC2 parameters not presentsamePOWER OFFSETN/APOWER OFFSET Parameter notpresent.GSM450GSM 480General signalling conditions for all carriersCipheringyesyesGeneral RF-conditions for all carriersFrequency hopping modeNon-hoppingNon-hoppingPropagation prof
11、ileStaticStaticDownlink Input Level63 dBmVemf( )63 dBmVemf( )Uplink output powerMinimum accordingMinimum accordingto MS power classto MS power classServing cell, BCCH/CCCH carrierChannel ARFCN263310Alternative channels274 or 276321 or 323Serving cell, Traffic channel, SDCCHChannel ARFCN267314Alterna
12、tive channels275 or 279322 or 326Power Control Indicator00Neighbouring cells BCCH/CCCH carriersChannel ARFCN260, 281, 284, 287, 290, 293307, 328, 331, 334, 337, 340Alternative channels261, 280, 283, 286, 289, 292308, 327, 330, 333, 336, 339Input level53 dBmVemf( )53 dBmVemf( )Network dependent param
13、etersCell identity0001H0001HMobile country code, MCC001 (decimal)001 (decimal)Mobile network code, MNC01 (decimal)01 (decimal)Location area code, LAC0001H0001HFrequency ListRange 128Range 128BCCH allocation sequence00number(BA_IND)Cell Channel DescriptorRange 128Range 128PLMN colour code, NCC11BS co
14、lour code, BCC55SMS Cell Broadcastnot activenot activeDTXMS must not useMS must not useIMSI Attach-detachMS shall not applyMS shall not applyCCCH_CONF1 basic physical channel for1 basic physical channel forCCCH combined with SDCCHCCCH combined with SDCCHBS_AG_BLKS_RES0 blocks reserved0 blocks reserv
15、edBS_PA_MFRMS5 paging subgroups5 paging subgroupsGSM450GSM480CELL_BAR_ACCESS(not barred)(not barred)Call-reestablishment (RE)(allowed)(allowed)Emergency Call allowedallowedsameAccess Control Classallowedsame(AC) (0.9, 11.15)Network dependent timersRadio_Link_Time-out88T3212 PeriodicInfiniteInfiniteu
16、pdating in decihoursAccess control parametersMax retrans11Tx-integer, nr. of slots55CELL_RESELECT_HYSTERESIS12 dB12 dBMS_TXPWR_MAX_CCHminimum levelminimum levelRXLEV_ACCESS_MINminimumminimumNECINew establishment causessameare not supportedACS (ADDITIONAL RESELECTIONNo additional cell parameterssameP
17、ARAM IND)are present in SI messages7 and 8C2 parametersC2 parameters not presentsamePOWER OFFSETN/AN/AGSM710 or GSM 750 or T-GSM 810GSM 850General signalling conditions for all carriersCipheringyesyesGeneral RF-conditions for all carriersFrequency hopping modeNon-hoppingNon-hoppingPropagation profil
18、eStaticStaticDownlink Input Level63 dBmVemf( )63 dBmVemf( )Uplink output powerMinimum accordingMinimum accordingto MS power classto MS power classServing cell, BCCH/CCCH carrierChannel ARFCN460150Alternative channels480 or 500170 or 190Serving cell, Traffic channel, SDCCHChannel ARFCN470160Alternati
19、ve channels490 or 510180 or 200Power Control Indicator00Neighbouring cells BCCH/CCCH carriersChannel ARFCN440, 445, 450, 455, 475, 495140, 210, 220, 230, 240, 250Alternative channels443, 448, 453, 465, 485, 505145, 215, 225, 235, 245, 251Input level53 dBmVemf( )53 dBmVemf( )Network dependent paramet
20、ersCell identity0001H0001HMobile country code, MCC001 (decimal)001 (decimal)Mobile network code, MNC011(decimal)011(decimal)Location area code, LAC0001H0001HFrequency ListRange 128Range 128BCCH allocation sequence00number(BA_IND)Cell Channel DescriptorRange 128Range 128PLMN colour code, NCC11BS colo
21、ur code, BCC55SMS Cell Broadcastnot activenot activeDTXMS must not useMS must not useIMSI Attach-detachMS shall not applyMS shall not applyCCCH_CONF1 basic physical channel for1 basic physical channel forCCCH combined with SDCCHCCCH combined with SDCCHBS_AG_BLKS_RES0 blocks reserved0 blocks reserved
22、BS_PA_MFRMS5 paging subgroups5 paging subgroupsGSM710 or GSM 750 or T-GSM 810GSM850CELL_BAR_ACCESS(not barred)(not barred)Call-reestablishment (RE)(allowed)(allowed)Emergency Call allowedallowedallowedAccess Control Classallowedallowed(AC) (0.9, 11.15)Network dependent timersRadio_Link_Time-out88T32
23、12 PeriodicInfiniteInfiniteupdating in decihoursAccess control parametersMax retrans11Tx-integer, nr. of slots55CELL_RESELECT_HYSTERESIS12 dB12 dBMS_TXPWR_MAX_CCHminimum levelminimum levelRXLEV_ACCESS_MINminimumminimumNECINew establishment causesNew establishment causesare not supportedare not suppo
24、rtedACS (ADDITIONAL RESELECTIONNo additional cell parametersNo additional cell parametersPARAM IND)are present in SI messagesare present in SI messages7 and 87 and 8C2 parametersC2 parameters not presentC2 parameters not presentPOWER OFFSETN/AN/APCS1900General signalling conditions for all carriersC
25、ipheringyesGeneral RF-conditions for all carriersFrequency hopping modeNon-hoppingPropagation profileStaticDownlink Input Level63 dBmVemf( )Uplink output powerMinimum accordingto MS power classServing cell, BCCH/CCCH carrierChannel ARFCN590Alternative channels690 or 730Serving cell, Traffic channel,
26、 SDCCHChannel ARFCN650Alternative channels750 or 780Power Control Indicator0Neighbouring cells BCCH/CCCH carriersChannel ARFCN520, 600, 700, 720, 760, 780Alternative channels530, 610, 710, 740, 770, 790Input level53 dBmVemf( )Network dependent parametersCell identity0001HMobile country code, MCC001
27、(decimal)Mobile network code, MNC011 (decimal)Location area code, LAC0001HFrequency ListRange 512BCCH allocation sequence0number(BA_IND)Cell Channel DescriptorRange 512PLMN colour code, NCC1BS colour code, BCC5SMS Cell Broadcastnot activeDTXMS must not useIMSI Attach-detachMS shall not applyCCCH_CON
28、F1 basic physical channel forCCCH combined with SDCCHBS_AG_BLKS_RES0 blocks reservedBS_PA_MFRMS5 paging subgroupsPCS1900CELL_BAR_ACCESS(not barred)Call-reestablishment (RE)(allowed)Emergency Call allowedsameAccess Control Classsame(AC) (0.9, 11.15)Network dependent timersRadio_Link_Time-out8T3212 Pe
29、riodicInfiniteupdating in decihoursAccess control parametersMax retrans1Tx-integer, nr. of slots5CELL_RESELECT_HYSTERESIS12 dBMS_TXPWR_MAX_CCHminimum levelRXLEV_ACCESS_MINminimumNECIsameACS (ADDITIONAL RESELECTIONsamePARAM IND)C2 parameterssamePOWER OFFSETN/AThese informations are provided by system
30、 information 1, 2, 3 and 4 messages.The system information elements which are broadcast on the SACCH during the dedicated mode should be consistent with those sent on the BCCH when the MS was in idle mode prior to the channel request.In addition, all fill paging messages sent on the paging sub-chann
31、els will have by default, their page mode set to NORMAL PAGING.26.1.2Structured sequence of the testsThe tests shall be performed in the order as indicated in the following table.The validity of the tests depends upon the results of the tests performed before.Channel request (basic test)RR26.2.1Imme
32、diate assignmentRR26.6.1IMSI attach/detach (basic)RR26.2.2PagingRR26.6.2Test of the mobile station functions in idle modeRR26.3Frequency redefinitionRR26.6.6Measurement report (incl. system info not idle)RR26.6.3AuthenticationMM26.7.2Cipher mode settingRR26.6.8IdentificationMM26.7.3Sequenced MM/CM m
33、essage transfer.26.2.3Channel releaseRR26.6.12Location updatingMM26.7.4TMSI reallocationMM26.7.1Classmark changeRR26.6.11Call control (verification on CC state diagram)CC26.8.1.1 and26.8.1.2Call rearrangementCC26.8.1.4.4DTMF information transferCC26.8.1.4.1HandoverRR26.6.5Additional assignmentRR26.6
34、.9Partial releaseRR26.6.10Re-establishmentCC26.8.2Dedicated channel assignment (during calls)RR26.6.4Transmission mode changeRR26.6.7Mobility management connection establishmentMM26.7.5Test of Layer 3 error handling26.5User to user signallingCC26.8.3Testing of structured procedures26.9E-GSM or R-GSM
35、 signalling26.10Multiband signalling26.1126.1.3General rules for message parametersThe following rules concerning message parameters apply to clause 26:1)Those values of parameters which are a consequence of the context of a test and which are not specific to that test need not be defined.2)If the v
36、alue of a parameter of an uplink message (MS to Network) is specified in a test, the implicit meaning is that it has to be checked; if the value is not specified, it is not to be checked unless stated otherwise.3)An optional field or optional Information Element of a downlink message (Network to MS)
37、, the presence of which is not a consequence of a test description, shall be absent in that test.4)If an optional field or Information Element is not indicated for the uplink (MS to Network) - unless specified otherwise -, it may be included or not.5)The Protocol Discriminator, Transaction Identifie
38、r and Message Type of all uplink messages have to be checked.26.1.4General rules for layer 3 testingUnless otherwise specified, before the SS pages the MS, the MS must be given the necessary time to be able to receive paging (see clause 20). In addition and unless otherwise specified,the SS must wai
39、t at least 1s after the last time slot of the message block containing a CHANNEL RELEASE, before sending a PAGING to the mobile (see 3GPPTS 04.13).In the signalling tests, where the following statement is used:-the RF level of cell x is set sufficiently low to ensure that cell x is not suitable as d
40、efined in 3GPPTS 05.08 subclause 6.6.2;this means that for the cell to be not suitable by virtue of its RF level, the RF level is to be lowered until C1 is below0.26.1.5Format of layer 3 test descriptionsIn subclauses 26.2, 26.5, 26.6, 26.7, 26.9, 26.10 and 26.11 a rigorous description technique is
41、used which is defined here.For every test, a subclause titled method of test and a subclause titled expected sequence define the exact test steps and the verifications to be performed in the test. These subclauses are normative and give requirements for the MS behaviour. The information of both subc
42、lauses applies.For the message contents further normative requirements for the MS behaviour are defined in the following parts which apply in the following order (starting with the highest) on basis of the general rules of 26.1.3:-specifications in the method of test and expected sequence subclauses
43、;-specifications in the subclause titled specific message contents;-specifications in the subclause default message contents at the end of the relevant subclauses 26.5, 26.6, 26.7, 26.9, 26.10 or 26.11;-specifications of default conditions in subclause 26.1.The relevant section may contain the defin
44、ition of abbreviations of L3 message names that are used in that section.In many cases, a test description contains an introductory subclause explaining the background of the relevant procedures and explaining why the tests of that description are essential.For every test, test purposes are given. In general conformance testing methodology, the correspondence between test purposes and test cases can be n to m: To one test purpose more than one test case may correspond (e.g. different