《ps教程入门—Photoshop制作逼真水龙头流水特效.doc》由会员分享，可在线阅读，更多相关《ps教程入门—Photoshop制作逼真水龙头流水特效.doc（11页珍藏版）》请在三一文库上搜索。
1、Photoshop制作逼真水龙头流水特效原图和最终效果图的对比1.先将图1这副图片保存到某个位置。图12.在Photoshop中将保存的图片打开。 3.新建一个图层，选择工具箱中的“钢笔工具”，绘制水流路径，如图2所示。图2继续绘制。图3完成绘制。图44.在“路径”调板中按住Ctrl键的同时单击路径层，得到如图5所示的路径选区。图55.按D键将前景色和背景色设置为默认的黑色和白色，然后按Ctrl+Del将选区填充为白色，如图6所示。图66.选择菜单命令“选择修改收缩”，如图7所示。图7在“收缩选区”对话框中将“收缩量”设置为2像素，如图8所示。设置完毕单击“确定”按钮。图8然后按Alt+Del
2、将选区填充为黑色，如图9所示。图97.再用类似的方法收缩，并填充为白色，如图10所示。图108.仍然采用这样的方法，填充为黑色，最后按Ctrl+D取消选择，如图11所示。图119.选择“滤镜扭曲玻璃”，如图12所示。图12按图13所示进行设置。图13设置完毕单击“确定”按钮，得到如图14所示的结果。图1410.按Ctrl+J复制一个副本图层，并将副本图层的混合模式改为“颜色加深”，如图15所示。图15 现在已经有点儿水流的意思了，如图16所示。图1611.选择工具箱中的“涂抹工具”，在选项栏中将“强度”值设置得小一点儿，如6%，如图17所示。图17仔细地涂抹几下，不宜过多，心里想着水流的真实样
3、子，可以得到如图18所示的效果。图1812.按Ctrl+U打开“色相/饱和度”对话框，按图19所示进行设置。图19设置完毕单击“确定”，得到最终的流水特效，如图20所示。图20from oil conservator rated. 4.1.12.10.3 oil is finished, should be set aside for 24 hours. 4.1.12.10.4 can be replaced after the transformer, cooling unit, gas relays and pressure release valve devices, exhaust g
4、as related sites multiple times. 4.1.13 electric overall construction process chart, see next page. Turn off the security system, access to the site had to wear a helmet, aerial work have to fasten your seat belt. Using power tools, the shell shall be reliable grounding to prevent electric shock, do
5、 the construction site security, preventing mounted electrical components and material damage, such as lost, electrical simulation test and operation of the transmission, and carry out the operation and the tone system; ongoing safety and quality education, improving safety awareness to ensure smoot
6、h and safe, high quality finish. 4.3 projects 4.3.1 quality assurance measures preparation of construction organization design and construction program. Careful review of the drawings, in-depth understanding of site, construction workers doing construction gives the low-down, prior to construction a
7、s far as possible the problems right. 4.3.2 compliance with specifications, in accordance with the drawings, encountered in the process of unclear are not free to change, must inform the unilateral changes by the design department to modify. 4.3.3 site full-time quality inspector and team part-time
8、Inspector on construction quality of electrical installation check, nonconforming areas for corrective actions in a timely manner until it reaches the required. 4.3.4 installed in well construction record, done self-inspection, mutual, total work quality appraisal work, improve the quality of workers and ensure the project progress in order