《c语言写的fir低通滤波器[计算机类].doc》由会员分享，可在线阅读，更多相关《c语言写的fir低通滤波器[计算机类].doc（5页珍藏版）》请在三一文库上搜索。
1、根据fir滤波器的公式y(n)=h(m)x(n-m);(m: 0(N-1).利用MATLAB产生滤波器系数（h（n）并归一化，下面为一个LP滤波算法void filter(void)uint16 i,j;fp32 sum;int16 x12030;fp32 h19= -0.0027, -0.0025, 0.0050, 0.0157, -0.0000, -0.0471, -0.0482, 0.0838, 0.2953, 0.4013,0.2953, 0.0838, -0.0482, -0.0471, -0.0000,0.0157, 0.0050, -0.0025, -0.0027;for(i=0
2、;i2020;i+)x1i = data0i;for(i=0;i2020;i+)sum=0.0;for(j=0;j= j)sum+=hj*x1i-j;else;data0i=(int16)sum;for(i=0;i2000;i+)data0i = data0i+20;考虑到前19个点为不完全累加和，故抛去前19个点。（应该是前后各18个点都是不完全累加和，都应该去掉，对于数据分段进入滤波器的情况，应该把前一段的后面数据放到下一段的前面，这段时间我在解调FSK时遇到了这个问题，通过滤波器的数据的分段处理。）设输入数据xN,输出数据yN,滤波器系数hn1.直接法(由y(m)=h(0)*x(m)+h
3、(1)*x(m-1)+.+h(N-1)*x(m-n-1);void fir(short x, short h, short y) int i,j; long long sum; for (j = 0; j N; j+) sum = 0; for (i = 0; i 15; 乘法器使用次数：N*n2.逆推法：void fir(short x, short h, short y) int i,j; long sum; for (j = 0; j n; j+) for (i = 0; i 15; 乘法器使用次数：N*n3.倒序法：（输入输出可以是同一量）void fir(short x, short
4、 h, short y) int i,j; long long sum; for (j = N; j 0; j-) sum = 0; for (i = n; i 0; i-) sum += xj-i * hi; yj = sum 15; #include #include #define true 1#define false 0#define n 8#define bufsize 100 /* the buffer size is 100 */* global declarations */int in_bufferbufsize; /* processing data buffers */
5、int out_bufferbufsize;/* functions */static int processing(int *input, int *output);static void dataio(void);static long round(long a);void main() int *input = &in_buffer0; int *output = &out_buffer0; puts(the 1st experiment startedn); /* loop forever */ while(true) /* * read input data using a prob
6、e-point connected to a host file. * write output data to a graph connected through a probe-point. */ / read the input signal. / if the input file is sine1.dat, the signal contains 300hz,400hz and 500hz. / if the input file is sine2.dat, the signal contains 100hz,400hz and 500hz. / the sampling frequ
7、ency is 1200hz. dataio(); /* remove the frequency compoment of 400hz and 500hz*/ processing(input, output); / write the output signal. / the output file is result.dat. dataio(); /* * = processing = * * function: apply a low-pass fir filter to input signal and remove the frequency higher than 350hz.
8、* * parameters: address of input and output buffers. * * return value: true. */static int processing(int *input, int *output) int i,size = bufsize; short xx0,x,y; / short zn=0,0,0,0,0,0,0,0,0; short zn=0,0,0,0,0,0,0,0;/short w2*n+1=22,356,155,990,466,220,777,216,777,26,466,9,155,0,22;/short w2*n+1=6
9、,457,56,1024,224,418,523,382,784,99,784,43,523;/ short w2*n+1=330*2,3299*2,1982*2,6867*2,4955*2,1594*2,6607*2,1065*2,4955*2,109*2,1982*2,17*2,330*2; /short w2*n+1=661,6598,3964,13733,9910,3187,13214,2131,9910,217,3964,34,661; / short w2*n+1=58,5628,526,8192,2105,5883,4913,3829,7369,1543,7369,504,491
10、3,102,2105,14,526,1,58; /short w2*n+1=28,4432,280,8192,1259,4883,3356,3975,5873,1509,7048,644,5873,142,3356,30,1259,3,280,0,28; / short w2*n+1=26,651,182,1024,545,421,909,247,909,51,545,11,182,1,26;/short w2*n+1=831,20846,5815,32768,17445,13486,29075,7888,29075,1647,17445,349,5815,21,831;/short w2*n
11、+1=208,5211,1454,8192,4361,3371,7269,1972,7269,412,4361,87,1454,5,208; short w2*n+1=101,4356,810,8192,2835,3403,5670,2517,7088,605,5670,193,2835,21,810;/ short w2*n+1=101,4356,810,8192,2835,3403,5670,2517,7088,605,5670,193,2835,21,810,2,101; / short w2*n+1=50,3814,454,8192,1815,3504,4235*,3084,6353,
12、831,6353,349,4235,50,1815,8,454,0,50; long y0,z0;/22222222222222 while(size-) xx0=*input+; x=xx0*6; z0=(long)x15; y0=0; for(i=0;i15); y0=round(y0); for(i=n-1;i0;i-) zi=zi-1; z0=round(z0); z0=(short)(z015); y=(short)(y015); *output+ =y; /* additional processing load */ return(true);/* * = dataio = * * function: read input signal and write processed output signal. * * parameters: none. * * return value: none. */static void dataio() /* do data i/o */ return;static long round(long a) long x3; x3=a&(0xffff0000); return x3;5网络软硬件