《环氧树脂水下底漆的施工方案.doc》由会员分享，可在线阅读，更多相关《环氧树脂水下底漆的施工方案.doc（3页珍藏版）》请在三一文库上搜索。
1、环氧树脂水下底漆的施工方案Intended Uses用途环氧树脂水下底漆设计用于新结构平台的维护保养以及暴露于海上的严重锈蚀部分如平台支架，水面以上管道和水下管道，采用潜水员水下施工方法。This product is designed for maintenance of new construction platform, together with all serious corrosion parts exposed to marine environment including platform support, pipeline above water and underwater
2、 application can be done by diverProductDescription产品简介二罐装，无溶剂环氧树脂涂料，用于长期保护浸于水中或潮汐的设备和平台。Two packages, solvent-free, epoxy resin paint, suitable for long term protection of equipmentsand plat forms immersed in water or tidelandProductInformation产品数据Volume Solids 体积固体份50%ccording 10 100%Dry Film Thic
3、kness 干膜厚度3 mm-6 mm 3毫米-6毫米Theoretical Coverage 理论涂布率0.1m2 /Kg at 100% volume solids and 6000 microns of dry film thickness 0.1平方米/公斤,以规定的体积固体份和6000微米干膜厚计Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Color 颜色Green after stirring(A: yellow , B: blue)搅拌后呈绿色（甲：黄色， 乙：蓝色）Application Details施工详述Mix
4、 Radio 混合比2 parts to 1 part by weight 重量比 2：1Method of Application 施工方法Only daub by hand 只可用于手工涂抹Thinner 稀释剂 Not necessary 不需要Cleaner 油漆设备清洗剂 C003Pot Life 使用期 20-1h 小时（use within 30minutes） 20-1h 小时（应于30分钟内使用）Storage 贮存期 One year 一年Drying time 干燥时间SubstrateTemperature底材温度,Touch Dry表干（h）Hard Dry硬干(h）
5、Over coating Interval覆涂间隔Mix最短Max最长52535/1684/Storage andHandling贮存与管理Storage 贮存 Store under dry, cool conditions 贮存于干凉条件下Pack size 包装规格 A;20Kg in 20 liter container 甲:20公斤装于20公升容器中 B:10Kg in 10 liter container 乙:10公斤装于10公升容器中Flash Point 闪点 No flash point in normal 正常情况下没有闪点Specific Gravity 比重 1.6Kg
6、/L 1.6公斤/公升Specification and Surface preparation技术要求及表面处理Iron or steel:Remove grease to SSPC-SP1 by solvent cleaning. Remove weld slag, smooth welded seams and sharp edges.http:/ Blast clean to white metal according to SSPC-SP10 or Swedish Standard Sa2.5. The steel roughness should be no more than 7
7、5um after blasting. In particular area the the surface should be St3 standard with power tool.铁与钢：用溶剂清洗除去油脂，去除焊渣，并磨平焊道及尖锐边缘，喷砂处理至白铁状为 SSPC-SP10或 Sa2.5瑞典标准SIS055900,喷砂后表面粗糙度不大于75微米，在特殊区域，表面应用动力工具处理至St3标准。Limitations 限制 In calm and tide less condition and good weather, this product may be manually app
8、lied to small surface under water by driver, For tube construction, firstly twine PVC net around the new blasted construction tightly, then daub by hand.在天气良好，风平浪静，无潮水状况下，本产品可由潜水员在水下就小面积部分进行手工涂装，对于管式钢结构来说，应先将PVC钢紧紧缠绕在新喷砂的结构上，然后用手工涂抹。Safety Precautions 安全措施This product should be used in painting area
9、 by professional operators. When painting, please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.Although this paint is flammable, so must be far away from open flames. If paint g
10、ets in touch with skin, was fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorptio
11、n of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safety precautions (Refer to the specifications), our company will NOT be responsible for any accid
12、ent. 本产品由专业人缘在工业场所使用，使用时请参照本说明书及健康安全手册,如客户在使用本产品前,未能仔细了解有关产品的健康安全知识，请与本公司联系。该涂料为无溶剂型涂料，为避免事故或危险发生，应采取最低限度的安全措施如下：此涂料为可燃涂料，应远离火星和明火。采取有效措施以防止皮肤和眼睛与涂料接触(如使用工作服，手套，护目镜，面罩及涂防护油等)如产品不慎接触到皮肤，应用温水及肥皂或适当的工业清洁剂彻底清洗，如眼睛受到污染,用清水冲洗至少10分钟，并立即就医。建议佩戴通风面罩以避免吸入漆雾和有害溶剂气体，尤其在通风不良环境下施工时，细心处理旧漆桶以免污染环境。 责任声明：对于未按本公司要求采取有效安全措施儿引起的安全事故，本公司不负任何责任。来源：江苏纽克莱涂料有限公司官网 http:/www.nsk-