《list of Metallurgical Engineering Division Council.docx》由会员分享，可在线阅读，更多相关《list of Metallurgical Engineering Division Council.docx（26页珍藏版）》请在三一文库上搜索。
1、list of Metallurgical Engineering Division CouncilINDIAN STANDARDSMETALLURGICAL ENGINEERING DIVISION COUNCIL (MTD) SR. No. CAT DESCRIPTIONIS 8: 1983 MTD15High heat duty fireclay refractories (forth revision)IS 277: 1992 MTD 4 Galvanized steel sheet (plain and corrugated)(fifthrevision)(Amendments 3)
2、IS 483: 1972 MTD15 Fireclay refractories for oil-fired boiler furnaces of naval ships (first revision)IS 513: 1994 MTD 4 Cold rolled low carbon steel sheets and strips (fourthrevision) (Amendment 1)IS 814: 1991 MTD11 Covered electrodes for manual metal arc welding of carbon and carbon manganese stee
3、l (fifth revision) (Amendments 3)IS 815: 1974 MTD11 Classification coding of covered electrodes for metal arc welding of structural steels (second revision)(superseded by IS 814:1991)IS 822: 1970 MTD11Code of procedure for inspection of welds.IS 1161: 1958 MTD19Steel tubes for structural purpose (fo
4、urth revision)IS 1182: 1983 MTD21 Recommended practice for radiographic examination of fusion welded butt joints in steel plates (second revision)IS 1239 (Part 1):1990 MTD19Mild steel tubes, tubulars and other wrought steel fittings:Part 1 Mild steel tubes (fifth revision) (Amendments 5)IS 1239 (Par
5、t 2):1992 MTD19Mild steel tubes, tubulars and other wrought steel fittings:Part 2 Mild steel tubulars and other wrought steel pipefittings (fourth revision) (Amendments 2)IS 1279: 1958 MTD19 Electrically welded mild steel boilers and superheatertubes for design steam temperatures not exceeding 155 d
6、egree centigrade or 850 degree centigrade (supersededby IS 1914)IS 1337: 1993 MTD20 Electroplated coatings of hard chromium for engineering purpose (third revision)IS 1395: 1982 MTD11 Low and medium alloy steel covered electrodes for manual metal arc welding (third revision)Is 1403 (Part 1):1993 MTD
7、32Mechanical testing of metals reverse bend test: Part 1Sheet and strip (second revision) (Amendment 1)Is 1442: 1964 MTD11 Covered electrodes for metal arc welding of high tensile structural steel (revised) (superseded by IS 814)IS 1526: 1960 MTD15Sizes and shapes for firebricks (Amendment 1)IS 1528
8、 (Part 10): 1974 MTD15Determination of size of refractory bricks (first revision)IS 1545: 1994 MTD 8 Solid drawn copper and copper alloy tubes for condenserand heat exchanger (third revision) (Amendments 3)IS 1570: 1996 MTD16 Schedules for wrought steels for general engineering purpose (revised)IS 1
9、570 (Part 1):1978 MTD16Schedules for wrought steels: Part 1 steels specified bytensile and / or yield properties (first revision)IS 1570 (Part 2/Sec 1): 1979 MTD16Schedules for wrought steels: Part 2 Carbon steels(unalloyed steels) sec 1 wrought products (other thanwire) with specified chemical comp
10、osition and relatedproperties (first revision)IS 1570 (Part 2/Sec 2): 1987 MTD16Schedules for wrought steels: Part 2 Carbon steels(unalloyed steels) sec 2 Carbon steel wires with relatedproperties (first revision)IS 1570 (Part 3):1979 MTD16Schedules for wrought steels: Part 3 carbon and carbonmangan
11、ese free cutting steels (first revision)IS 1570 (Part 4):1988 MTD16Schedules for wrought steels: Part 4 Alloy steels (alloyconstructional and spring steels) with specified chemicalcomposition and mechanical properties (first revision)IS 1570 (Part 5):1985 MTD16Schedules for wrought steels: Part 5 St
12、ainless and heatresisting steels (second revision)IS 1570 (Part 6):1996 MTD16Schedules for wrought steels: Part 6 Carbon and alloy toolsteels (first revision)IS 1570 (Part 7):1992 MTD16Schedules for wrought steels: Part 7 Steels for elevatedtemperature service (creep resistant steels)IS 1586: 1988 M
13、TD 3 Method for Rockwell hardness test for metallic material(scales A-B-C-D-E-F-G-H-K) (second revision)IS 1598: 1977 MTD 3 Method for izod impact test of metals (first revision)IS 1599: 1985 MTD 3 Method for bend test (second revision) (superseding IS1692:1974, Is 3260:1960 and IS 4598:1968)IS 1608
14、: 1995 MTD 3 Mechanical testing of metals tensile testing (secondrevision) (superseding IS1521, 1663, 1816, 1894, 2078,2654, 2655, 2656, 2657, 2658, 4713 and 8285)IS 1870: 1965 MTD16 Comparison of Indian and overseas standards for wrought steels for general engineering purpose.IS 1871 (Part 1):1987
15、MTD16Commentary on Indian standard schedules for wroughtsteels: Part 1 Steels specified by Tensile and yieldproperties (Complementary to IS 1570(Part 1): 1978(first revision)IS 1871 (Part 2):1987 MTD16Commentary on Indian standard schedules for wroughtsteels: Part 2 Carbon steels (unalloyed steels)(
16、Complementory to Is 1570 Part 2): 1979 (first revision)IS 1871 (Part 3):1987 MTD16Commentary on Indian standard schedules for wroughtsteels: Part 3 Carbon and carbon manganese free cuttingsteels complementary to IS 1570(Part 3): 1978 (firstrevision)IS 1875: 1992 MTD18 Carbon steel billets, blooms, s
17、labs and bars for forgings (fifth revision) (Amendment 2)IS 1914 (Part 1 to 4): 1982 MTD19Carbon steel boilers tubes and superheater tubes (secondrevision)IS 1977: 1996 MTD 4 Low tensil structural steels (third revision)IS 2002: 1992 MTD 4 Steel plate for pressure vessels for intermediate & hightemp
18、erature service including boilers (second revision)(Amendment 2)IS 2004: 1991 MTD18 Carbon steel forgings for general engineering purpose (third revision)IS 2041: 1995 MTD 4 Steel plates for pressure vessels used at moderate andlow temperature (second revision) (Amendment 1)IS 2042: 1972 MTD15Insula
19、ting bricks (first revision) (Amendment 1)IS 2049: 1978 MTD 1 Colour code for the indentification of wrought steels forgeneral engineering purpose (first revision) (Amendment1)IS 2062: 1992 MTD 4 Steel for general structural purpose (fourth revision)(superseded IS: 226:1975) (Amendments 4)IS 2328: 1
20、983 MTD 3 Method for flattening teat on metallic tubes (first revision) IS 2329: 1985 MTD 3 Method for bend test on metallic tubes (first revision)IS 2330: 1986 MTD 3 Method for flanging test on metallic tubes (first revision) IS 2335: 1985 MTD 3 Method for drift expanding test on metallic tubes (fi
21、rstrevision) (Amendment 1) (Superseding IS 2348:1963 andIS 4599:1968)IS 2478: 1991 MTD21 Glossary of terms relating to industrial radiography (second revision)IS 2595: 1978 MTD21Code of practice for radiographic testing (first revision)IS 2598: 1966 MTD21Safety code for industrial radiographic pract
22、iceIS 2611: 1964 MTD18 Carbon chromium molybdenum steel forgings for high temperature servicesIS 2811: 1987 MTD12 Recommendations for manual tungsten inert gas arc welding of stainless steel (first revision)IS 2856: 1987 MTD17 Carbon steel castings for pressure containing parts suitable for high tem
23、perature service (fusion welding quality) (third revision) (Amendment 1)IS 2986: 1990 MTD17 Steel castings for marine engines and boilers (second revision)IS 3038: 1992 MTD17 Martensitic stainless steel and alloy steel castings for pressure containing parts suitable for high temperature service (thi
24、rd revision)IS 3407 (Part 1):1983 MTD 3 Method for creep testing of steel at elevated temperature: Part 1 Tensile creep testing (first revision) (superseded IS3408: 1965) A3 = Reaffirmed 1989IS 3407 (Part 2):1983 MTD 3 Method for creep testing of steel at elevated temperature: Part 2 Tensile creep s
25、tress rupture testing (first revision)(superseded IS 3409: 1965)IS 3410: 1993 MTD 3 Metalic materials determination of liner thermalexpansion (first revision)IS 3415: 1998 MTD 21 Glossary of terms used in magnetic particle flow detection(second revision)IS 3422: 1966 MTD 4 Code of practice for packa
26、ging of steel and steel productsfor export purposeIS 3444: 1987 MTD 17 Corrosion resistant alloy steel and nickel base castings forgeneral applications (Second revision) (Amendment 1)IS 3502: 1994 MTD 4 Steel chequered plates (second revision)IS 3503: 1966 MTD 4 Steel for marine boilers, pressure ve
27、ssels and weldedmachinery structuresIS 3531: 1997 MTD 24 Glossary of terms relating to corrosion of metals (secondrevision)IS 3589: 1991 MTD 19 Seamless or electrically welded steel pipes for water, gasand sewage (168.3 to 2032 mm outside diameter)(second revision)IS 3600 (Part 1):1985 MTD 11 Method
28、s of testing fusion welded joints ad weld metal in steel: Part 1 Cruciform fillet weld tensile testIS 3600 (Part 2):1985 MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 2 Beam impact (charpy V-notch) testIS 3600 (Part 3):1984 MTD 11 Methods of testing fusion welded joints
29、 ad weld metal in steel: Part 3 Transverse tensile test on butt weldsIS 3600 (Part 4):1984 MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 4 Longitudinal tensile test on cylindrical weldmetal test pieces on butt weldsIS 3600 (Part 5):1983 MTD 11 Methods of testing fusion
30、welded joints ad weld metal in steel: Part 5 Tranverse root and face bend test on buttweldsIS 3600 (Part 6):1983 MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 6 Transverse side bend test on butt weldsIS 3600 (Part 7):1985 MTD 11 Methods of testing fusion welded joints a
31、d weld metal in steel: Part 7 Longitudinal root and face bend test on buttweldsIS 3600 (Part 8):1983 MTD 11 Methods of testing fusion welded joints ad weld metal in steel: Part 8 Nick break test and fillet weld fracture testIS 3600 (Part 9):1985 MTD 11 Methods of testing fusion welded joints ad weld
32、 metal in steel: Part 9 Macro and micro examinationIS 3601: 1984 MTD 19 Steel tubes for mechanical and general engineeringpurpose (first revision) (Amendments 2)IS 3609: 1966 MTD 19 Chrome molybdenum steel, seamless, boiler andsuperheater tubes (Amendments 2)IS 3613: 1974 MTD 11 Acceptance tests for
33、 wire flux combination for submergedarc welding (first revision) (Amendment 1)IS 3658: 1999 MTD 21 Code of practice for liquid penetrant flaw detection(second revision)IS 3703: 1980 MTD 21 Code of practice for magnetic particle flaw detection (firstrevision)IS 3711: 1990 MTD 3 Wrought steel selectio
34、n and preparation of samples andtest pieces for mechanical tests (first revision)IS 3747: 1982 MTD 4 Hot rolled steel plates and sheets for flanging andpressing (first revision) (superseded by IS 5986:1992)IS 4260: 1986 MTD 21 Recommended practice for ultrasonic testing of butt weldsin ferritic stee
35、l (second revision)IS 4353: 1995 MTD 12 Submerged arc welding of mild steel and low alloy steels -Recommendations (first revision)IS 4522: 1986 MTD 17 Heat resistant alloy steel and nickel base castings (secondrevision)IS 4712: 1984 MTD 19 Forged steel socket welding fittings (first revision)(Amendm
36、ent 1)IS 4853: 1982 MTD 21 Recommended practice for radiographic inspection offusion welded butt joints in steel pipes (first revision)IS 4943: 1968 MTD 11 Assessment of butt and fillet fusion welds in steel sheet,plate and pipeIS 5206: 1983 MTD 11 Covered electrodes for manual metal arc welding ofs
37、tainless steel and other similar high alloy steels (firstrevision)IS 5334: 1981 MTD 21 Code of particle for magnetic particle flaw detection ofwelds (first revision)IS 5511: 1991 MTD 11 Covered electrodes for manual metal arc welding of castiron (first revision) (Amendment 1)IS 5530: 1987 MTD 12 Rec
38、ommendations for production, rectification and repairof steel castings by metal arc welding process (firstrevision)IS 5555: 1970 MTD 24 Code of practice for conducting field studies onatmospheric corrosion of metals (Amendment 1)IS 5788: 1986 MTD 6 Iron castings with spheroidal or nodular graphite f
39、orpressure containing parts for use at elevated temperature(first revision) (Amendment 1)IS 5789: 1993 MTD 6 Austenitic spheroidal graphite iron casting for pressurecontaining parts suitable for low temperature service (firstrevision)IS 5986: 1992 MTD 4 Hot rolled steel plates, sheets strips and fla
40、ts for flangingand forming operation (first revision) (Amendments 4)IS 6009: 1970 MTD 20 Method for evaluation of result of accelerated corrosiontestIS 6286: 1971 MTD 19 Seamless and welded steel pipes for sub zerotemperature service (Amendment 1)IS 6392: 1971 MTD 19 Steel pipe flanges (Amendment 1)
41、IS 6410: 1991 MTD 21 Magnetic flaw detection links and powders (first revision) IS 6419: 1996 MTD 11 Welding rods and bare electrodes for gas shielded arcwelding of structural steels (first revision)IS 6431: 1972 MTD 11 Tolerances on dimensions of plates cut by flameIS 6601: 1987 MTD 17 Permissible
42、deviations in chemical composition forproducts analysis of steel castings (with amendmentNo.1) (first revision) (Amendment 1)IS 6630: 1972 MTD 19 Seamless ferritic alloy steel pipes for high temperaturesteam service (first revision)IS 6911: 1992 MTD 16 Stainless steel plate, sheet and strip (first r
43、evision)(Amendment 1)IS 6913: 1973 MTD 19 Stainless steel tubes for the food and beverage industryIS 7307 (Part 1):1974 MTD 11 Approval tests for welding procedures: Part 1 fusion welding of steel (Amendment 1)IS 7310 (Part 1):1974 MTD 11 Approval tests for welders working to approved welding proced
44、ures: Part 1 fusion welding of steelIS 7318 (Part 1):1974 MTD 11 Approval tests for welders when welding procedure approval is not required: Part 1 Fusion welding of steelIS 7598: 1990 MTD 1 Classification of steels (first revision)IS 7899: 1992 MTD 17 Alloy steel castings suitable for pressure serv
45、ice (secondrevision)IS 8062 (Part 1):1976 MTD 24 Code of practice for cathodic protection of steel structures: Part 1 General principlesIS 8062 (Part 3):1977 MTD 24 Code of practice for cathodic protection of steel structures: Part 3 Ships hullIS 8629 (Part 1):1977 MTD 24 Code of practice for protec
46、tion of iron and steel structures from atmospheric corrosion: Part 1 General principles ofcorrosion and its prevention (Amendment 1)IS 8629 (Part 2):1977 MTD 24 Code of practice for protection of iron and steel structures from atmospheric corrosion: Part 2 Pretreatment(Amendment 1)IS 8629 (Part 3):1
47、977 MTD 24 Code of practice for protection of iron and steel structures from atmospheric corrosion: Part 3 Protection schemes(Amendment 1)IS 8780: 1978 MTD 21 Code of practice for non destructive testing of steelcastings (Amendment 1)IS 8791IS 8800: 1997 MTD 17 Technical delivery conditions for stee
48、l castings (excludinginvestment castings) (third revision)IS 8849: 1991 MTD 26 Glossary of terms relating to fuel fired industrial furnaces IS 9158: 1979 MTD 19 Cold drawn high pressure fluid power cylinder tubes(Amendment 1)IS 9172: 1979 MTD 24 Recommended design practice for corrosion prevention ofsteel structuresIS 9180