《电源适配器规格书.doc》由会员分享，可在线阅读，更多相关《电源适配器规格书.doc（28页珍藏版）》请在三一文库上搜索。
1、SPECIFICATION 电源适配器规格书 FOR SWITCHING AC ADAPTER PRODUCT 产品名称： AC-DC ADAPTER 电源适配器推荐精选MODEL 产品型号 ：MTP051CC-0510EPART NO 产品编号 ： C109-6234 REV 版本 : A1CUSTOMER 客户 :斯莱普ISSUE DATE 发行日期： 2013-9-26受领印栏*未签回而下订单即视同认可!发 行 行 印 印推荐精选 工 程品管业务 发 行 部核刘伟审黄弯经张鑫 署 栏 准 核 办SHENZHEN MOUNTPOWER INDUSTRY CO., LTD. No 2, 2R
2、oad, XiaoShan Industrial Park, HuangPu, Shajing Town, Shenzhen City, China TEL:+86-755-27682455FAX:+86-755-81736210Website：推荐精选DOCUMENT NO:C109-6234 A1PAGE 1 OF 133/27/2014 推荐精选CONTENTS 内容 1. Scope 范围.4 2. Electrical Requirements 电性能要求.42.1Input Voltage Requirements 输入特性42.1.1Input Voltage 输入电压 42.1
3、.2Input Voltage Range 输入电压范围 42.1.3Input Current 输入电流.42.1.4Input Frequency 输入频率.42.1.5Inrush Current 浪涌电流.42.1.6Power Efficiency 效率42.1.7Leakage Current 漏电流.42.1.8Power Factor 功率因数.42.2Output Voltage Requirements 输出特性.52.2.1Normal DC Output Voltage 输出空载电压.52.2.2DC Output Voltage Range 额定负载输出电压.52.2
4、.3Load Current Range 额定输出电流.52.2.4Peak Load Current 峰值电流.52.2.5Ripple & Noise纹波.52.2.6Hold-UP Time 保持时间.52.2.7Turn-ON Delay Time 延迟时间.52.2.8Dropout Time 回动时间.52.2.9Line Regulation Rate 线性调整率.52.2.10 Load Regulation Rate 负载调整率52.2.11Transient Response 瞬态响应.52.2.12 Voltage Drift 电压飘移52.3Protection
5、 保护.52.3.1Out Over Current Protection 过流保护.52.3.2Short Circuit Protection 短路保护.5推荐精选DOCUMENT NO:C109-6234 A1PAGE 2 OF 133/27/2014 推荐精选2.3.3Over Temperature Protection 过温保护52.3.4Output Voltage Protection 输出过压保护.52.4Green Mode Requirement 绿色电源要求.52.5Isolation Requirements 绝缘要求62.5.1HI-POT 高压要求62.5.2In
6、sulation Resistance 绝缘电阻.62.5.3Insulation Class 绝缘等级63.Safety & EMC Requirements 安规标准要求.63.1EMI/EMS 电磁兼容干扰.63.2Safety Requirements 安规要求.64.Environmental Requirements 使用环境要求.64.1Temperature 温度.64.2Humidity 湿度.75.Reliability 可靠性75.1Calculated MTBF 平均间隔故障时间估算.75.2Demonstrated MTBF 证明 MTBF.75.3Usefu
7、l Life 使用寿命/有效期75.4Burn-In 煲机75.5Ac Plug Strength AC 插头强度75.6DC Cord Bending 直流电源线的弯曲.85.7Temperature Up With 温度与85.8Vibration 震动测试.85.9Drop Test 跌落测试.86.Mechanical Requirements 机械特性.96.1AC Input Type 初级输入插头类型.96.2DC Output Type 次级输出插头类型96.3DC Output Cable 次级输出线类型.96.4Weight 产品重量96.5Case Material 外壳
8、线材.96.6PCB Material 线路板材料.96.7Outline Dimension 外形尺寸106.8Marking and Labeling 铭牌标准11推荐精选7.Packing 包装.12DOCUMENT NO:C109-6234 A1PAGE 3 OF 133/27/2014 推荐精选8. Modify 修改12 1.0Scope 范围This specification defines the functional requirements and characteristics ofMTP051CC-0510E AC-DC Switching power supplie
9、s.该产品规格书定义产品 MTP051CC-0510E 属于开关电源的功能要求及特性要求2.0Electrical Requirements 电性能要求*TEST MEASURES 测试方法C1：0.1uF CERAMICS CAPACITOR 瓷片电容; C2：10uF 50V ALUMINUM CAPACITOR 电解电容2.1Input Voltage Requirements 输入特性ITEMSPECIFICATIONMINTYP.MAX项目规格/测试条件最小额定最大1.NORMAL INPUT VOLTAGE(Vrms)SINGLE PHASE 单相额定输入电压2. INPUT VO
10、LTAGE RANGE(Vrms)SINGLE PHASE 单相100240输入电压范围推荐精选3. INPUT CURRENT(A)输入电流TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD输入最大电流0.5 推荐精选4.INPUT FREQUENCY(Hz)SINGLE PHASE 单相475063推荐精选输入频率推荐精选5.INRUSH CURRENT(A)TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD , 25.推荐精选浪涌电流在室温 25 度，额定电压输入和满载输出推荐精选6.EFFICIENCY
11、(%)TYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD推荐精选效率额定电压输入和人满载输出DOCUMENT NO:C109-6234 A1PAGE 4 OF 133/27/2014 推荐精选7.LEAKAGE CURRENT(mA)TYPICAL INPUT VOLTAGE泄露电流额定电压输入8.POWER FACTORTYPICAL INPUT VOLTAGE& OUTPUT AT FULL LOAD功率因数额定电压输入和满载输出2.1.9INPUT FUSE 保险丝输入电路:The hot line side of the input s
12、hall have a fuse 在火线一边连接一颗保险丝2.1.10INPUT PROTECTION DEVICE 输入保护装置:An adequate internal fuse on the AC input line shall be provided. 安装在火线内部线路的保险丝提供保护作用2.2Output Voltage Requirements 输出特性ITEMSPECIFICATIONMINTYP.MAX项目规格/测试条件最小额定最大推荐精选1.NORMAL DC OUTPUT VOLTAGE(V)额定输出电压2. DC OUTPUT VOLTAGE RANGE(V)额定负载
13、输出电压TYPICAL OUTPUT VOLTAGE 输出额定电压5.04.75.3 推荐精选3. LOAD CURRENT RANGE (A)额定0推荐精选负载电流推荐精选4. PEAK LOAD CURRENT(A)峰值电流5.RIPPLE & NOISE(mV)纹波6.HOLD-UP TIME(ms)保持时间7.TURN-ON DELAY TIME(ms)延迟时间8 DROPOUT TIME(ms)回动时间9.LINE REGULATION RATE (%)线性调整率推荐精选TIME<60S 保持工作时间在 60 秒以内TYPICAL INPUT VOLTAGE&
14、OUTPUT AT FULL LOAD , 25.额定电压输入和额定电流输出 25TYPICAL INPUT VOLTAGE AND TYPICAL LOAD CURRENT定电压输入和额定电流输出TYPICAL INPUT VOLTAGE AND TYPICAL LOAD CURRENT定电压输入和额定电流输出TYPICAL INPUT VOLTAGE AND TYPICAL LOAD CURRENTCHANGE AC INPUT VOLTAGE .额定输出电流，从电压输入范围没 10V 调整，输出变化 推荐精选DOCUMENT NO:C109-6234 A1PAGE 5 OF 133/27
15、/2014 推荐精选10. LOAD REGULATION RATE (%)负STEP LOAD CHANGE IS 0.1 A/µsec.载调整率额定输入电压，从额定输出电流从 0A 开始调整到额定电流，输出电压变化11.TRANSIENT RESPONSE TIME(ms)STEP LOAD CHANGE IS 1 A/µsec. 10%-90%-10%的负载瞬态响应时间12. VOLTAGE DRIFT RATE (%)TYPICAL INPUT VOLTAGE AND TYPICAL LOAD CURRENT , 25电压漂移率.2.3Protection 保护IT
16、EMSPECIFICATIONMINTYP.MAX项目规格/测试条件最小额定最大推荐精选1. OUT OVER CURRENT PROTECTION(A)输出过流保护The power supply shall be protected against output overloads. Thepower supply is not damaged or life degraded by continuous operationin output overloads.当产品电流输出一定的电流范围，产品进入打嗝模式，产品自动保护，解除短路后，产品自动恢复正常2.5推荐精选2.SHORT CIRC
17、UIT PROTECTION产品短路保护The power supply shall be protected against short circuits. The powersupply is not damaged or life degraded by continuous operation in short circuit.产品不管在输出轻载还是满载情况下，短路输出端产 品会自动保护，并且去掉断开保护后，产品恢复正常Pa 推荐精选3. OVER TEMPERATURE PROTECTIONN/A推荐精选过温保护推荐精选4.Output Voltage Protection(v)Wh
18、en the power supply output voltage over 15V,the power supplyN/A8推荐精选输出过压保护Protection 产品在输出一定的电压范围会自动保护推荐精选2.4Green Mode Requirements 绿色能效要求推荐精选2.4.1When the switching power supply working on stand by mode and no loads, the inputpower will less than 0.3 W. 当产品在额定输入电压，空载输出的时候，功率损耗小于 0.3W. 推荐精选DOCUMENT
19、 NO:C109-6234 A1PAGE 6 OF 133/27/2014 推荐精选2.5Isolation Requirements 绝缘要求ITEM 项目SPECIFICATION OR TEST CONDITION 规格/测试条件ACCEPTANCE CRITERIA 接受标准1.HI-POT 高压测试INPUT TO OUTPUT, 1500Vac 60 SECONDS 5mANO DAMAGE输入对输出，1500 伏交流点时间为 60 秒，设置电流为 5MA不损坏2.INSULATION RESISTANCEINPUT TO OUTPUT,DC 500V>10M绝缘电阻测试输入
20、对输出直流 500V3.INSULATION CLASSINSULATION CLASS OF TRANSFORMERCLASS B绝缘等级变压器绝缘系统，符合 UL 要求3.Safety & EMC Requirements 安规标准要求ITEM 项目SPECIFICATION OR TEST CONDITION 规格/测试条件ACCEPTANCE CRITERIA 接受标准1.EMI/EMS 电磁兼容干扰MEET EN55022EMC2.SAFETYREQUIREMENTSMEET EN60950CE，GS安规4.Environmental Requirements 环境要求ITE
21、M 项目SPECIFICATION OR TEST CONDITIONMINTYP.MAX规格/测试条件最小额定最大1.OPERATINGTEMPERATURE定电流输入和额定电流输出040操作温度 2. STORAGE TEMPERATURE-2085存储温度 4.OPERATING HUMILITYNON-CONDENSING5%RH90%RH操作湿度5.STORAGE HUMILITYNON-CONDENSING5%RH90%RH存储湿度5.Reliability 可靠性ITEMSPECIFICATION OR TEST CONDITIONACCEPTANCE CRITERIA项目规格/
22、测试条件接受标准推荐精选DOCUMENT NO:C109-6234 A1PAGE 7 OF 133/27/2014 推荐精选1.CALCULATED MTBFMEET MIL-HDBK-217F30000 HOURS满足 mil-hdbk-217fMTBF 计算30000 小时2.DEMONSTRATED MTBFTYPICAL INPUT&FULL LOAD , 2550000 HOURS平均间隔故障时间估算在室温 25 度，额定输入和输出的条件下50000 小时3.USEFUL LIFE 有效期限TYPICAL INPUT&FULL LOAD, 40典型的输入和满负荷 40
23、°1YEARS ABOVE 一年以上TYPICAL INPUT&FULL LOAD, 25 典型的输入和满负荷 25°2YEARS ABOVE 两年以上4. BURN-IN 煲机AT 30(±10),NORMAL INPUT VOLTAGE24 HOURS2-4 小时在温度为 30+-10 度的环境推荐精选5.AC PLUG STRENGTHAC 插头强度THERE MUST NOT BE SHAKING AND WIRE BREAKINGWHEN 98N IN 1 MINUTE IS ADDED TO THE AC PLUG FTO EVERY DIRE
24、CTION。不能有振动和断丝 98n 在 1 分钟时被添加到 AC 插头 各个方向THERE MUST NOT BESHAKING AND WIRE BREAKING不能有震动和段丝 推荐精选NORMAL TEMPERATURETHERE WILL BE推荐精选THE CORD SHALL WITHSTAND WEIGHT OF 200g,NO ABNORMALITY推荐精选SWINGING FROM LEFT TO RIGHT AT AN ANGLE OF 60NO APPEARANCE推荐精选DEG。1000CYCLE TIMES MIN.将有推荐精选S/R SHALL WITHSTAND
25、 WEIGHT OF 1N.无异常推荐精选SWINGING FROM LEFT TO RIGHT AT AN ANGLE OF没有出现推荐精选6.DC CORD BENDING60DEG. 1000CYCLE TIMES MIN.推荐精选直流电源线的弯曲BENDING SPEED 40CYCLE/MINUTE.正常温度 线应能承受体重 200 左右摇摆在 60 分钟 deg 1000cycle 倍角的权利 S/R 应能承受重量 1. 左右摇摆的 60 度角的权利， 1000cycle 次分钟 弯曲速度 40cycle/分钟. 7.TEMPERATURE UP WITH TEST AT SURF
26、ACE OF THE CASE WITH TYPICAL AC TEMPERATURE UP UNDER INPUT AND TYPICAL LOAD, IN OUTPUT 50/60Hz.40 DEGREES。温度在典型的交流输入，典型的负载的情况下表面测试温度下 40°输出 50/60HZ推荐精选8.VIBRATION震动测试FREQUENCY RANGE:1055Hz 频率范围为：10-55HzAMPLITUDE:1.5mm 振幅为：1.5MMACCELERATION: 1G 加速：1GSWEEP 1 MINUTE FOR X,Y,Z,AXIS EACHX.Y.Z.坐标轴各震动
27、 1 分钟THERE SHALL BE NOABNORMALITY NO THEAPPEARNCE STRUCTUREAND OPERATING。不能出现异常 推荐精选推荐精选DOCUMENT NO:C109-6234 A1PAGE 8 OF 133/27/2014 推荐精选UNIT SHALL WITHSTAND WITHOUT EXPOSURE OF LIVEUNIT SHALL WITHSTANDPARTS AFTER DROPPING 3 TIME （BY X，Y，Z DIRECTIONWITHOUT EXPOSURE OF9.DROP TESTEACH 1 TIME）FROM 100
28、 CM HIGH ONTO A WOODENLIVE PARTS。BOARD。产品不能变形或者脱开，功跌落测试跌落高度为 1 米，跌落为厚度 20 毫米的硬木板上，且硬木板能必须正常输出要平放在水泥地面上，不能放在有弹性的地方，三个面各 2次推荐精选6.Mechanical Requirements 机械要求6.1AC INPUT TYPE 输入插头类型:6.2DC OUTPU TYPE 输出插头类型:6.3DC OUTPUT CABLE 输出线类型:6.4WEIGHT 产品重量:6.5CASE MATERIAL 外壳材料:6.6PCB MATERIAL 线路板材料:DOCUMENT NO:C
29、109-6234 A13/27/2014推荐精选2 PIN CCCUSB 4PIN 母座 PIN 1：+ PIN 4：-''+''''-''ABOUT35（g）94 V-0 ABS+PC.94 V-0PAGE 9 OF 13 推荐精选6.7 OUT LINE DIMENSION 外形尺寸:According to the drawing 根据图纸PIN 1 "-"PIN 4 "+"推荐精选DOCUMENT NO:C109-6234 A1PAGE 10 OF 133/27/2014 推荐精选6
30、.8 LABEL 标签According to the drawing 根据图纸C109-6234 推荐精选DOCUMENT NO:C109-6234 A1PAGE 11 OF 133/27/2014 推荐精选7. Packing 包装According to the drawing 根据图纸推荐精选蛋格 :L: 78*6=468W :56*6=336H=58垫板 :PE袋 :L=150 * W =120 厚度 ： 0.03包装方法 :PE袋 +蛋格 +外箱 每层 72PCS分 4层装入大箱 在每一层加垫板 共 5PCS垫板 推荐精选L=480 * W =340 * H=3 外箱 : L=49
31、0 * W =350 * H=265 装入 288 PCS 产品 FINISH推荐精选MATERIALREV.NAMEPACKING 推荐精选DEG.CHKD.APPD.UNIT推荐精选SCALEREF.PARTDWGNO.NO.推荐精选C109-6234 推荐精选DOCUMENT NO:C109-6234 A1PAGE 12 OF 133/27/2014 推荐精选8.0Modify 修改According to the sheet 根据表变更版本变更日期变 更 内 容推荐精选DOCUMENT NO:C109-6234 A1PAGE 13 OF 133/27/2014 （注：可编辑下载，若有不当之处，请指正，谢谢!） 推荐精选