《变频器调试说明.docx》由会员分享，可在线阅读，更多相关《变频器调试说明.docx（17页珍藏版）》请在三一文库上搜索。
1、真理惟一可靠的标准就是永远自相符合.土地是以它的肥沃和收获而被估价的；才能也是土地,不过它生产的不是粮食,而是真理.如果只能滋生瞑想和梦想的话,即使再大的才能也只是砂地或盐池,那上面连小草也长不出来的1 .变频器上电,修改参数访问级别.首先选中变频器,按键,然后按口键,选择Ports选择 “00 PowerFlex 753,按 ESC键,退到主界面.设置 P301=1快速访问方法按PAR#,输入访问的参数号,如 3012 .完成变频器Start-up向导按d然后按I 或键,选中Start-up菜单,进入启动向导.启动向导结构如下：选择Begin Start Up,按确认键进入.面板提示 Sta
2、rt-Up consists of several steps to configure the drive.Press Enter,按 Enter键确认.面板提示Geneal Startup“Appl Specific 选择Geneal Startup,按Enter 键确认面板显示：Motor Control Motor DataFeedbackLimitsRef Ramp StopI/O顺序选择以上菜单进入选择Motor Control 菜单,面板显示 This section select the type of Motor Control the drive will use.Pres
3、sEnter,按Enter键确认面板显示：Please Select:Sensorless VectV/HzFlux Vector对于原料变频器,选择Sensorless Vecf无速度传感器矢量,对于烧结机一台变频器带两台电机应用,选择“ V/HzMotor Control设置完成后,选择Motor Data ,按Enter确认变频器面板显示“Edit Motor NP Volts400 VAC按Enter确认变频器面板显示Select type of power units shown on motor nameplateHPKW选择“KW,按“ Enter键确认变频器面板显示Edit M
4、otor NP PowerXX KW,输入电机额定功率使用 软按键,删除原有显示值再输入电机功率值,按Enter键确认变频器面板显示Edit Motor NP AmpsXX AmpS,输入电机额定电流值,按Enter键确认变频器面板显示Edit Motor NP HertzXX Hz变频器额定是50Hz,按Enter键确认变频器面板显示Edit Motor NP RPMXX RPM,输入电机额定转速,按Enter键确认变频器面板显示Edit Motr OL Factor1 电机缺省过载倍数为1,按Enter键确认变频器面板显示Edit Motor PolesXX PoleT ,输入电机极数注意
5、：4极电机同步转速1500RPM, 6极电机同步转速1000RPM,按Enter键确认变频器面板显示Edit Speed UnitsHz 0缺省是“Hz 0,按Enter键确认如果要改为RPM,这里设置“RPM 1Motor Data设置完成后,可直接跳过Feedback,变频器缺省工作在无编 码器反应模式,选择Limits,按Enter键确认变频器面板显示Edit Max Fwd Speed50Hz按Enter键确认变频器面板显示Edit Max Rev Speed-50Hz按Enter键确认变频器面板显示Edit Min Fwd Speed0.0 Hz按Enter键确认变频器面板显示Edi
6、t Min Rev Speed0.0 Hz按Enter键确认Lim让s设置完成后,选择Tests,按Enter键确认变频器面板显示Complete these steps in orderDirection TestAuto TuneDone选择 a direction test,按 Enter键确认变频器面板显示Press START to begin test!Motor will run!J.键起动变频器变频器面板显示Is the direction of rotation forward?YesNo如果变频器旋转方向为正向,选择“Yes,按Enter键确认如果变频器旋转方向为反向,选择
7、“No,按Enter键确认变频器面板显示How would you like to fix motor polarity?Automatic ChangeChange mtr wires选择Automatic Change,按 Enter 键确认变频器面板显示Press STOPStartup will then automatically change rotation as if motor lead were reversed. gl按键停止变频器变频器会再次显示Press START to begin test!4 人生的磨难是很多的,所以我们不可对于每一件稍微的伤害都过于敏感.在生活
8、磨难面前,精神上的 坚强和无动于衷是我们反抗罪恶和人生意外的最好武器.Motor will run!J 键起动变频器变频器面板显示Is the direction of rotation forward?YesNo选择Yes,按Enter键确认Direction Test完成后,选择Auto Tune变频器面板显示IMPORTANT ! Use Rotate Tune for best results.Rotate Tune works best under no load/low friction condition.Use Static Tune if load can not be ro
9、tated .Press Enter 按Enter键确认变频器面板显示Select the tuning mode:Rotate Tune 旋转调Static Tune静态调节选择Rotate Tune,按Enter键确认变频器面板显示Press START to begin test.CAUTION:Rotate Tune will cause motor shaft rotation.变频器会自动完成整定过程,整定结束后,按 J 键停止变频器,选择 Done,按 Enter键确认.Tests完成后,选择Ref Ramp Stop,按Enter键确认变频器面板显示Edit Direction
10、 ModeUnipolar 0按Enter键确认变频器面板显示Please select the speed reference source:Local HIMAnalog InputMore Choices选择Analog Input,按 Enter 键确认变频器面板显示Edit Spd Ref A selSelect Port to useZero SpeedPort 00 PowerFlex 753Port 04 I/O Module 24V 选择Port 00 PowerFlex 753,按 Enter 键确认变频器面板显示Edit Spd Ref A SelSelect param
11、eter To Use按向下方向键翻页,选中 Par 0558 MOP Reference,按Enter键确认变频器面板显示Edit DI MOP IncSelect Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选中Port 04 I/O Module 24V ,按 Enter 键确认变频器面板显示Edit DI MOP IncSelect Param To UsePar 0001 Dig In Sts;选中Par 0001 Dig In Sts,按 Enter键确认变频器面板显示Edit DI MOP IncS
12、elect Bit To Use选中Bit 03 Input 3 ,按Enter键确认这里I/O Module 24V DI 3接机旁操作箱频率上升按钮,实际选择哪位以现场接线为准变频器面板显示Edit DI MOP DecSelect Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选中Port 04 I/O Module 24V,按 Enter 键确认变频器面板显示Edit DI MOP DecSelect Param To UsePar 0001 Dig In Sts;选中Par 0001 Dig In Sts
13、,按 Enter键确认变频器面板显示Edit DI MOP DecSelect Bit To Use选中Bit 04 Input 4 ,按Enter键确认这里I/O Module 24V DI 4接机旁操作箱频率下降按钮,实际选择哪位以现场接线为准变频器面板显示Edit MOP Rate1.000%/S按Enter键确认变频器面板显示Do you want to save MOP speed at stop?NoYes选择No,按Enter键确认变频器面板显示Do you want to save MOP speed at power down?NoYes选择No,按Enter键确认变频器面板
14、显示Edit Stop Mode ARamp 1按Enter键确认变频器面板显示Edit Bus Reg Mode AAdjust Freq 1 按Enter键确认变频器面板显示Edit Accel Time 110.00 Secs暂时用缺省加速时间10秒钟,按Enter键确认变频器面板显示Edit Decel Time 110.00 Secs暂时用缺省减速时间10秒钟,按Enter键确认变频器面板显示Do you want to perform S-Curve for accel/decal?NoYes选择Yes,按Enter键确认变频器面板显示Edit S Curve Accel0.00%
15、修改为10%,按Enter键确认变频器面板显示Edit S Curve decel0.00%修改为10%,按Enter键确认以上设置完成后,选择“I/O,按Enter键确认变频器面板显示Make a selection:Start Stop & Dir,二.选择Start Stop & Dir,按 Enter 键确认变频器面板显示This section defines Start Stop and Direction digital input functions. Press Enter 按Enter键确认变频器面板显示Will a digital input be used as a S
16、TART source?NoYes选择Yes,按Enter键确认变频器面板显示Is REVERSE required from a digital input?NoYes选择NO,按Enter键确认变频器面板显示Enter choice for the control method:3 wire2 wire选择2 wire,按Enter键确认变频器面板显示Edit DI RunSelect Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选择Port 04 I/O Module 24V,按 Enter 键确认变频器面
17、板显示Edit DI RunSelect Param To UsePar 0001 Dig In Sts;选中Par 0001 Dig In Sts ,按 Enter 键确认变频器面板显示Edit DI RunSelect Bit To Use选中Bit 01 Input 1 ,按Enter键确认这里I/O Module 24V DI 1接运行命令,实际选择哪位以现场接线为准变频器面板显示Edit Digital In CfgRun Edge 0按Enter键确认设置完Start Stop & Dir后,直接跳过Digital Inputs Digital Outputs Analog Out
18、puts,选择Done,按 Enter键确认.再次选择Done ,按Enter键确认.变频器面板显示Please make selection真理惟一可靠的标准就是永远自相符合.土地是以它的肥沃和收获而被估价的；才能也是土地,不过它生产的不是粮食,而是真理.如果只能滋生瞑想和梦想的话,即使再大的才能也只是砂地或盐池,那上面连小草也长不出来的General StartupAppl SpecificExit Startup选择Exit Startup,按Enter键确认,退出启动向导剩余的工作是完成对I/O Module的设置.首先选中I/O Module ,按键,然后按Ufl岐:键,选择Port
19、s,选择 “04 I/O Module 24V ,I/O设置数字量输入,输出和模拟量输出Digital in 选择digital in status bit 1为运行已经通过设置向导设置好了 Digital output 设置RO0设置:按 PAR# 10,按 EDIT 键变频器面板显示Edit RO0 SelSelect Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选择Port 00 PowerFlex 753 ,按 Enter 键确认用向下方将键选中“Par 0935 Drive Status 1 ,按Ent
20、er键确认选中“Bit 00 Ready ,按Enter键确认RO1设置:按 PAR# 20,按 EDIT 键变频器面板显示Edit RO01SelSelect Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选择Port 00 PowerFlex 753 ,按 Enter 键确认用向下方将键选中“Par 0935 Drive Status 1 ,按Enter键确认选中“Bit 16 Running ,按 Enter 键确认设置模拟量输出信号类型为毫安信号按 PAR# 70,按 EDIT 键变频器面板显示Port 0
21、7 Host Param 70Anlg Out TypeXXXXXXXX00按EDIT键,把最低两位都设为“1 ,按Enter键确认AO1设置按 PAR# 85,按 EDIT 键变频器面板显示Edit Anlg Out 1 SelSelect Port to useDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V 选择 Port 00 PowerFlex 753 ,按 Enter 键确认变频器面板显示Edit Anlg Out 1 SelSelect Param to use.选择Par 0001 Output Frequency ,按 E
22、nter 键确认设置模拟量输入信号类型为毫安信号按 PAR# 45,按 EDIT 键变频器面板显示Port 07 Host Param 45Anlg In TypeXXXXXXXX00按EDIT键,把最低两位都设为“1 ,按Enter键确认选中 Port 00 PowerFlex 753,按PAR# 550 ,按Enter键确认变频器面板显示Port 00 Dev Param 550Spd Ref B Sel ,按 EDIT 键变频器面板显示“Edit Spd Ref B selSelect Port to useZero SpeedPort 00 PowerFlex 753Port 04 I
23、/O Module 24V 选择Port 04 Port 04 I/O Module 24V,按 Enter 键确认变频器面板显示Edit Spd Ref B SelSelect parameter To UsePar 0050 Anlg In 0 ValuePar 0060 Anlg In 1 Value按向下方向键翻页,选中Par 0060 Anlg In 1 Value,按Enter键确认最后完本钱体和远程速度给定切换按PAR# 174 ,按Enter键确认变频器面板显示Port 00 Dev Param 174Spd Ref B SelDI Speed Sel 1 ,按 EDIT 键变
24、频器面板显示Edit DI Speed Sel 1Select Port To UseDisabledPort 00 PowerFlex 753Port 04 I/O Module 24V选择 Port 04 I/O Module 24V,按 Enter 键确认变频器面板显示Edit DI Speed Sel 1Select Param To UsePar 0001 Dig In Sts选择 Par 0001 Dig In Sts 按 Enter 键确认变频器面板显示Edit DI Speed Sel 114人生的磨难是很多的,所以我们不可对于每一件稍微的伤害都过于敏感.在生活磨难面前,精神上的坚强和无动于衷是我们反抗罪恶和人生意外的最好武器.真理惟一可靠的标准就是永远自相符合.土地是以它的肥沃和收获而被估价的；才能也是土地,不过它生产的不是粮食,而是真理.如果只能滋生瞑想和梦想的话,即使再大的才能也只是砂地或盐池,那上面连小草也长不出来的Select Bit To Use选择Bit 02 Input 2,按 Enter 键确认I/O Module Input 2断开时,使用本地机旁操作箱升速按钮和降速按钮调节频率；I/O Module Input 2闭合时,使用远程 PLC模拟量调节频率；