《工业热电阻安装说明书.docx》由会员分享，可在线阅读，更多相关《工业热电阻安装说明书.docx（18页珍藏版）》请在三一文库上搜索。
1、工业热电阻安装说明书WZ口系列工业热电阻WZ series of industrial thermalresistance安装使用说明书ion at all nst上海辰心仪表有限公司Shanghai Chenxin Instruments Co,Ltdwzn口系列工业热电阻安装使用说明书一、概述WZ口系列工业热电阻是我厂生产的温度传感器中的一个系列，它测温的精度较热 电偶高，与显示仪表配套，以直接测量生产过程中200C- +600C范围内的液体、气体 介质以及固体表面等的温度。它广泛用于石油、化工、机械、冶金、电力、轻纺、食品、 原子能、宇航等工业部门和科技领域。二、工作原理热电阻的作用是利
2、用物质在温度变化时本身电阻也随着发生变化的特性来测量温 度。三、选择1 .根据测量的范围和对象，选择适当的工业热电阻型号以及保护管材料，热电阻的 “最高使用”压力不可超过在该工作温度下保护管所能承受的压力。2 .选用工业热电阻的分度号必须与显示仪表的分度号一致。3 .除双支式的工业热电阻外，在不使用切换开关的情况下，每支工业热电阻不可同时 和两支显示仪表连接使用。四、工业热电阻的基本性能在0C时公称电阻值（R。）及测温允差（见下表）:0时测温范围、精度等的公级和允差分度电阻电阻比R100/R(0)测温范()精度等级 和允差(0)(Q)1.3850P PT1 10陶瓷元 件：A级：土0-200F
3、600 玻璃元 件： -200*+500 云母元 件： -100*+420(0.15+0. 2%lt 1 )B级：土(0.3+0.5 %l tl )PT100100wz c分度 号0时 的电 阻值 R(0 )Q电阻比R100/R( 0)测温范目目、精度等级和允差测温范 围(C)精度等级 和允差Cu5050.000 0.051.4280 土0.002050 +100土(0.30+0.006 111 )Cui00100.00 0.10备注分度号为CulOO的铜热电阻和分度号为 PT10的般若电阻需协议供货注：D ItI为被测温度的绝对值。2）分度号为PtlO、PtlOO的工业钳电阻符合ZBY30L
4、85工业的热电阻技术条件及分度表标 准。3）分度号为Cu50. CulOO工业铜电阻符合ZBNI1010-88工业铜电阻技术条件及分度表标准。ZWZ口系列工业热电阻的常温绝缘电阻1 ） .工业钳热电阻的常温绝缘电阻值应不小于100MQ。2 ） .工业铜热电阻的常温绝缘电阻应不小于50MQ常温绝缘电阻的试验电压为1010010VDC（环境温度应在1535t范围内，相对湿度不大于 80%）o3 .WZ口系列工业热电阻的热响应时间保护管直径保护管，612碳钢20热响应时间t0.530 90不锈钢6160Crl8Nil2不锈钢30 90锥形保方铜热电阻lCrl8Ni 不锈钢 lCrl8Ni黄铜口 碳钢
5、20 不锈钢90180 180lCrl8Ni4 .WZ口系列工业热电阻的长度规格（单位：mm）1） .16 保护管规格（总长 L）有：300, 350, 400, 450, 500, 650, 900, 1150, 1650, 2150。3） .锥形保护管（总长 L）有：225, 250, 300, 350, 400。注：WZ口系列工业热电阻的插入长度l=L-150inmo五、安装1 .工业热电阻的安装地点，应避免安装在炉门旁边和避免与加热物体距离过近之处。2 .工业热电阻的接线盒不可碰到被测介质的容器壁，接线盒的温度不宜超过100C,并尽可 能地保持稳定不变。3 .工业热电阻的插入深度，浸入
6、被测介质中的长度应不小于保护管外径的10倍。六、使用注意事项L连接导线应采用绝缘（最好是屏蔽）铜线，截面积视工业热电阻与显示仪表间的距 离而定，但一般不得小于ISmn?。导线的电阻值应按显示仪表技术条件规定的数据配准 （一般为515C）,导线的电阻值可用惠斯顿电桥来调整。2 .增加被测介质的循环，使工业热电阻与被测介质间的对流传热增加。3 .当工业热电阻用来测量变化的温场时，常有动态误差的存在，请注意选用具有适当热响 应时间的工业热电阻，因为热响应时间的大小是决定动态误差大小的主要因素，并与之成正比, 它对温度的自动调节和控制起着相当重要的作用。4 .根据用户需要，我厂可为用户提供各种要求特殊
7、性能规格和尺寸的工业热电阻。可来人 来函联系以技术协议的形式供货。七、运输与保存工业热电阻在安装使用前，应保存在不受震动和碰撞的地方。最合适的存放场所条件为： 环境温度为-20+40C。相对湿度不大于80%的通风室内。且不含有对工业热电阻起腐蚀 作用的有害杂质。八、可能发生故障和修理/J故障现可能原因修理方法显示仪保护管（1）倒出水或消除灰尘,表指示值比实际值低或接线盒内有水、金属并将潮湿部分加以干燥处理（不得用火烤）、提高绝缘性能。或不值不稳定屑、灰尘 或热电 阻短路(2)用万能表检查短路或 界限地部分，并消除之， 如系感温元件短路，应进 行修复或更换。2显示仪 表指示 值无限 大热电阻 短
8、路(1)用万用表检查短路部 位，确定是连接导线还是 感温元件短路。(2)如系连接导线短路， 可以更换或修复。(3)如系感温元件短路， 应进行更换3显示仪 表指针 反向标 尺下限 值(1)热 电阻短路(2) 与现实 表接线接错(1)用万用表确定短路部 位，并消除之，如系感温 元件短路，应进行修复或 更换。(2)重新连接导线。九、补充说明产品验收：收到本产品后，请及时按产品国家标准或我厂标准规定的出厂 检验项目验收。若有质量问题，请于收货之日起一个月内(以用户来函邮戳日 期为准)函告我厂，我厂将及时受理。逾期则视为已验收合格。WZ seiies of industrial thermal resi
9、stance installation ManualL OverviewWZ series of industrial heat resistance is my factory production of temperature sensors in a series, the accuracy of its temperature higher than the thermocouple, and display instruments complementary to direct measurement of the production process -200 - +600 wit
10、hin the scope of Liquid, gas, and other media and the solid surface temperature. It widely used in petroleum, chemical, mechanical, metallurgical, power, textile, food, atomic energy, aerospace and other industrial sectors and technology areas.IL the principle ofHeat resistance is the role of temper
11、ature change in the use of substances at their own resistance to change also with the characteristics to measure temperature.IIL Choose1. According to measure the scope and targets, select appropriate models of industrial heat resistance and the protection of materials, heat resistance, nthe maximum
12、 use of pressure should be less than the temperature under the protection of the work can bear the pressure.2. Selection of the industrial sub-degree heat resistance, the instrument must be displayed at the same degree of.3. In addition to the double-supported industrial thermal resistance,is not in
13、 use, switch the circumstances, every industrial thermalresistance can not be displayed at the same time, and two connecting the use of instruments.IVe industrial thermal resistance of the basic propertiesL 0 at the nominal value of resistance (Ro) and temperaturetolerance (see table below):ModelInd
14、e xing0 at the nomin al Value R (0) (。)Resista nee thanR100/R (0 )Temperaturerange, accuracy class andToleranceTempe raturerange (ec)Accura cy class and Tolera neeWZPPT1 0101.3850Cerami c compo nents:GradeA: (0.15PT110000-200 to +600 Glass compo nents:-200 to +500Mica compo nents:-100 to +420+0.2% 1
15、11)Grade B: (0.3 +0.5% 111)wzcInde xing0 at the nomin al Value R (0) (。)Resista nee thanR100/R (0 )Temperaturerange, accuracy class andToleranceTempe raturerange ()Accura cy class and ToleraneeCu5050.0000.051.4280+0.002050 +100 (0.30+0.006 Itl )Cui00100.000.10Prepa ration NoteCulOO points for the de
16、gree of copper and sub-degree heat resistance, resistance to PT10 to be the Prajna agreement AvailabilityNote: 1) 111 for the measured temperature of absolute value.2), for sub-degree PtlO, PtlOO industrial platinum resistance with ZBY301-85 industrial platinum heat resistance and technicalcondition
17、s at Table11 standard*3), for sub-degree Cu50, CulOO industrial copper resistance with ZBNI1010-88 Copper resistance technology industry conditions and sub-Tablen standarde2.WZ series of industrial heat resistance of insulation resistance at room temperature1) Industrial platinum resistance at room
18、temperature thermal insulation resistance value of not less than 100 M 2.2). Industrial copper at room temperature thermal resistance of the insulation resistance should be not less than 50 M 2.At room temperature insulation resistance of the test voltage of 10100 10VDC (ambient temperature should b
19、e 15 35 range, relative humidity of not more than 80 per cent).3.WZ series of industrial heat resistance of thermal response time.Protection of the diameter (d)Protection of materialsHeatresponse time(seconds) t0.5(pl2Brass H6220 # carbon steel30 90(pl6Stainless steel 0Crl8Nil2M02Ti Stainless steel
20、lCrl8Ni9Ti30 90Cone of protectionStainless steellCrl8Ni9Ti90 18Copper thermal resistance(pl2Brass H6220 # carbon steelStainless steel !Crl8Ni9Ti 1804、WZ series of industiial heat resistance of the lengthspecifications (unit: mm)1) . 012 protection of the specifications (General L):225,250,300,350,40
21、0,450,550,650,900,1150.2) . 016 protection of the specifications (General L):300,350,400,450,500,650,900,1150,1650,2150.3) Cone of protection (General L): 225,250,300r350,400.Note: WZ series of industrial heat resistance insert length 1 = L-150mm.V . the installationL Thermal resistance of industria
22、l locations9 should be avoided in the Furnace Door installed next to the heating and avoid objects in the distance over the paste2. Industrial thermal resistance junction box can not meet the vessel wall measured media, the temperature junction box should not be 超过 100 , and as far as possible to ma
23、intain stability unchanged93. Industrial thermal resistance insertion depth, immersion in the medium measured the length of protection should be not less than 10 times the diameter.VI the use of Attention1. Connecting wire insulation should be used (preferably shielding) copper wire, cross-sectional
24、 area as industrial heat resistance and display meters and the distance between, but generally not less thanL5 mm2. Wire resistance values should be the instrument showed that technical requirements of the registration data (normally 5 15 Q), wire-resistance values can be used to adjust the Houston
25、Bridge.2. Tested medium to increase the cycle of industrial tested medium heat resistance and the spread of the increase3. When the industrial thermal resistance used to measure changes in temperature field, often the existence of dynamic error, please note that with the proper choice of response ti
26、me of industrial heat resistance, because the thermal response time is to determine the size of the main dynamic error, And with proportional to its temperature of the automatic adjustment and control plays a very important role.4. Based on user needs, I can plant to provide users with special requi
27、rements of performance specifications and size of industrial heat resistance. Can be our link to technology in the form of supply agreement.VIL transportation and predervationIndustrial thermal resistance in the installation, should be kept free of vibration, and the collision area. The most suitabl
28、e conditions for the storage places:Ambient temperature of -20 +40 Relative humidity of not more than 80 per cent of the indoor ventilatione Does not contain the industrial thermal resistance from the corrosive effect of harmful impurities*VIIL probably to a fault and repairNo.OccurrencePossible rea
29、sons forRepair Methods1Display Instrument instructions value or lower than the actual value indication of instabilityProtection of water or cable boxes, metal shavings, dust or heat resistance short circuit(1) Dispose of water or eliminate dust and damp to drying part (should not use a plate) to imp
30、rove insulation properties.(2) a universal inspection table to short-circuit or some limits, and the elimination of, such as temperature components of the short circuit, should be repairedor replaced.2Display Instrument instructions infinite valueThermal resistance short circuit(1) a short-circuit m
31、ultimeter site inspection to determine connecting wires or short-circuit temperature components.(2) In the case of connecting wires short-circuit, can be replaced or repaired.(3) In the case of short-circuit temperature components, should be replaced3Instrumentreverse(1) heat resistance(1) a short-c
32、ircuit multimeterbenchmark indicators show that lower limitshort circuit (2) and the reality connection to thewrong tabledetermine location, and the elimination of, such as temperature components of the short circuit, should be repaired or replaced.(2) re-connecting wires.IX. addedProduct acceptance
33、: receipt of this product, please timely products by national standards or our factory standards for factory acceptance test items. If it has quality problems, from the date of the receipt within one month (postmark date of the communication users), I set out plants, I plant will promptly accepted. Late acceptance is deemed to have qualified.