《muBS EN 1435-1997 A1A2-2003 焊缝的无损试验-焊接点的辐射检验.doc》由会员分享，可在线阅读，更多相关《muBS EN 1435-1997 A1A2-2003 焊缝的无损试验-焊接点的辐射检验.doc（29页珍藏版）》请在三一文库上搜索。
1、BS EN 1435-1997+A1A2-2003 焊缝的无损试验-焊接点的辐射检验BS EN BRITISH STANDARD1435:1997Incorporating Corrigendum No. 1 and Amendments Nos. 1 and 2Non-destructive testing of welds Radiographic testing of welded joints?The European Standard EN 1435:1997, with the incorporation of amendments A1:2002 and A2:2003, has
2、 the status of a BritishStandardICS 25.160.40 .bzfxw4#ff66ffBS EN 1435:1997National forewordThis British Standard is the English language version of EN 1435:1997, including amendments A1:2002 and A2:2003. It supersedes BS 2600-1:1983, BS 2600-2:1973, BS 2910:1986 and BS7257:1989, which are withdrawn
3、.The start and finish of text introduced or altered by amendment is indicated in the text by tags !;. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !;.As agreed by CEN/TC 121/SC 5 resolution 134/2000 and in ac
4、cordance with amendment A1:2002, the term “examination” has been replaced by “testing” throughout the document.The UK participation in its preparation was entrusted to Technical Committee WEE/46, Non-destructive testing, which has the responsibility to: aid enquirers to understand the text; present
5、to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on requ
6、est to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Ele
7、ctronic Catalogue or of BritishStandards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis
8、 document comprises a front cover, an inside front cover, the EN title page, pages 2 to 33 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.This British Standard, having been prepared under the Amendments issued since publicationdirecti
9、on of the Engineering Sector Board, was published under the authority of the Amd. No.DateCommentsStandards Board and comes into effect on 10616 August 1999Correction to Table 215 December 1997CorrigendumNo.1? BSI 15 March 20041398515 November 2002See national foreword1493815 March 2004Changes to for
10、eword and deletion of Annex ZAISBN 0 580 28913 3.bzfxw#ff66ffEUROPEAN STANDARDEN 1435August 1997NORME EUROP?ENNE+ A1May 2002EUROP?ISCHE NORM+ A2December 2003ICS 25.160.40Descriptors: Welded joints, fusion welding, butt welds, quality control, non-destructive tests, radiographic analysis, setting-up
11、conditions English versionNon-destructive testing of welds Radiographictesting of welded joints(includes amendments A1:2002 and A2:2003)Contr?le non destructif des assemblages Zerst?rungsfreie Prfung von soudsSchwei?verbindungen Contr?le par radiographie des assemblages Durchstrahlungsprfung von sou
12、dsSchmelzschwei?ungen(inclut les amendements A1:2002 et A2:2003)(enth?lt ?nderungen A1:2002 und A2:2003)This European Standard was approved by CEN on 1997-08-02. Amendment A1was approved by CEN on 2002-05-05; amendment A2 was approved by CENon2003-11-20. CEN members are bound to comply with the CEN/
13、CENELECInternal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCE
14、N member. This European Standard exists in three official versions (English,French, German). A version in any other language made by translation underthe responsibility of a CEN member into its own language and notified to theCentral Secretariat has the same status as the official versions.CEN membe
15、rs are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia,Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for StandardizationComit
16、 Europen de NormalisationEurop?isches Komitee fr NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels? 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national members.Ref. No. EN 1435:1997 + A1:2002 + A2:2003 E.bzfxw#ff66ffEN 1435:1997Foreword
17、Foreword to amendment A2This European Standard has been prepared by This document EN 1435:1997/A2:2003 has been Technical Committee CEN/TC 121, Welding, the prepared by Technical Committee CEN/TC 121, Secretariat of which is held by DS.Welding, the Secretariat of which is held by DS.This European St
18、andard shall be given the status of This amendment to the European Standard a national standard, either by publication of an EN1435:1997 shall be given the status of a national identical text or by endorsement, at the latest by standard, either by publication of an identical text February 1998, and
19、conflicting national standards or by endorsement, at the latest by June 2004, and shall be withdrawn at the latest by February 1998.conflicting national standards shall be withdrawn at the latest by June 2004. This document has been prepared under a mandate given to CEN by the European Commission an
20、d the This document has been prepared under a mandate European Free Trade Association.given to CEN by the European Commission and the European Free Trade Association.According to the CEN/CENELEC Internal Regulations, the national standards organizations According to the CEN/CENELEC Internal of the f
21、ollowing countries are bound to implement Regulations, the national standards organizations this European Standard: Austria, Belgium, Czech of the following countries are bound to implement Republic, Denmark, Finland, France, Germany, this European Standard: Austria, Belgium, Czech Greece, Iceland,
22、Ireland, Italy, Luxembourg, Republic, Denmark, Finland, France, Germany, Netherlands, Norway, Portugal, Spain, Sweden, Greece, Hungary, Iceland, Ireland, Italy, Switzerland and the United Kingdom.Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Ki
23、ngdom.Foreword to amendment A1This document EN 1435:1997/A1:2002 has been prepared by Technical Committee CEN/TC 121, Welding, the Secretariat of which is held by DS.This amendment to the European Standard EN 1435:1997 shall be given the status of a national standard, either by publication of an ide
24、ntical text or by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latest by November 2002.This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential
25、requirements of EU Directive(s).Annex A and Annex B are normative.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Gre
26、ece, Iceland, Ireland, Italy, Luxembourg, Malta Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.? BSI 15 March 20042.bzfx#ff66ffEN 1435:1997PageContents6Recommended techniques for makingPage radiographs 8Foreword26.1Test arrangements81Scope56.2Choice of tube voltage
27、and radiation 2Normative references5 source153Definitions56.3Film systems and screens173.1nominal thickness, t56.4Alignment of beam193.2penetrated thickness, w56.5Reduction of scattered radiation193.3object-to-film distance, b66.6Source-to-object distance193.4source size, d66.7Maximum area for a sin
28、gle exposure203.5source-to-film distance (SFD)66.8Density of radiograph213.6source-to-object distance, f66.9Processing223.7diameter, D6e6.10Film viewing conditions224Classification of radiographic techniques67Test report225General6Annex A (normative) Recommended number 5.1Protection against ionizing
29、 radiation6of exposures which give an acceptable testing of a circumferential butt weld235.2Surface preparation and stage of manufacture6Annex B (normative) Minimum image quality values285.3Location of the weld in the radiograph65.4Identification of radiographs75.5Marking75.6Overlap of films75.7Type
30、s and positions of image quality indicators (IQI)75.8Evaluation of image quality85.9Minimum image quality values85.10Personnel qualification83? BSI 15 March 2004.bzfxw#ff66ffblank4.bzfxw#ff66ffEN 1435:19971 ScopeThis European Standard specifies fundamental techniques of radiography with the object o
31、f enabling satisfactory and repeatable results to be obtained economically. The techniques are based on generally recognized practice and fundamental theory of the subject.This standard applies to the radiographic testing of fusion welded joints in metallic materials.It applies to the joints of plat
32、es or pipes. Besides its conventional meaning, “pipe” as used in this standard should be understood to cover other cylindrical bodies such as tubes, penstocks, boiler drums and pressure vessels. This standard complies with EN 444.This standard does not specify acceptance levels of the indications.If
33、 lower test criteria !are permitted by specification;, the quality achieved may be significantly lower than when this standard is strictly applied.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references a
34、re cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest
35、edition of the publication referred to applies.EN 444, Non-destructive testing General principles for the radiographic examination of metallic materialsusing X- and gamma-rays.EN 462-1, Non-destructive testing Image quality of radiographs Part 1: Concepts, image quality indicators(wire type), determ
36、ination of image quality value.EN 462-2, Non-destructive testing Image quality of radiographs Part 2: Concepts, image quality indicators(step/hole type), determination of image quality value.EN 462-3, Non-destructive testing Image quality of radiographs Part 3: Image quality classes for ferrousmetal
37、s.EN 462-4, Non-destructive testing Image quality of radiographs Part 4: Experimental evaluation of imagequality values and image quality tables.EN 473, Qualification and certification of non-destructive personnel General principles.EN 584-1, Non-destructive testing Industrial radiographic film Part
38、 1: Classification of film systems for industrial radiography.EN 584-2, Non-destructive testing Industrial radiographic film Part 2: Control of film processing by means of reference value.EN 25580, Non-destructive testing Industrial radiographic illuminators Minimum requirements. (ISO 5580:1985)3 De
39、finitionsFor the purpose of this standard, the following definitions apply.3.1 nominal thickness, tthe nominal thickness of the parent material only. Manufacturing tolerances do not have to be taken into account3.2 penetrated thickness, wthe thickness of material in the direction of the radiation be
40、am calculated on the basis of the nominal thicknessfor multiple wall techniques the penetrated thickness is calculated from the nominal thickness.5? BSI 15 March 2004.bzxw.omEN 1435:19973.3 object-to-film distance, bthe distance between the radiation side of the test object and the film surface meas
41、ured along the central axis of the radiation beam3.4 source size, dthe size of the radiation source3.5 source-to-film distance (SFD)the distance between the radiation source and the film measured in the direction of the beam3.6 source-to-object distance, fthe distance between the radiation source an
42、d the source side of the test object measured along the central axis of the radiation beam3.7 diameter, Dethe nominal external diameter of the pipe4 Classification of radiographic techniquesThe radiographic techniques are divided into two classes: class A: basic techniques; class B: improved techniq
43、ues.Class B techniques will be used when class A might be insufficiently sensitive.!Better techniques compared to class B are possible and may be defined by specification of all appropriate test parameters.;The choice of radiographic technique shall be !defined by specification.;If, for technical re
44、asons, it is not possible to meet one of the conditions specified for class B, such as type of radiation source or the source-to-object distance, f, it may be !defined by specification; that the condition selected may be that specified for class A. The loss of sensitivity shall be compensated by an
45、increase of minimum density to 3,0 or by the choice of a higher contrast film system. Because of the better sensitivity compared to class A, the test specimen may be regarded as tested within class B. This does not apply if the special SFD reductions as described in 6.6 for test arrangements 6.1.4 a
46、nd 6.1.5 are used.5 General5.1 Protection against ionizing radiationWARNING NOTICE. Exposure of any part of the human body to X-rays or gamma-rays can be highly injurious to health. Wherever X-ray equipment or radioactive sources are in use, appropriate legal requirements must be applied.Local or na
47、tional or international safety precautions when using ionizing radiation shall be strictly applied.5.2 Surface preparation and stage of manufactureIn general, surface preparation is not necessary, but where surface imperfections or coatings might cause difficulty in detecting defects, the surface sh
48、all be ground smooth or the coatings shall be removed.Unless otherwise specified, radiography shall be carried out after the final stage of manufacture, e.g. after grinding or heat treatment.5.3 Location of the weld in the radiographWhere the radiograph does not show the weld, high-density markers shall be placed on either side of the weld.? BSI 15 March 20046.bzxw#ff66ffEN 1435:19975.4 Identification of radiographsSymbols shall be affixed to each section of the object being radiographed. The images of these symbols shall appear in the radiograph