《国家紧固件标准GBT与汉语、英语对照表.doc》由会员分享，可在线阅读，更多相关《国家紧固件标准GBT与汉语、英语对照表.doc（11页珍藏版）》请在三一文库上搜索。
1、2 GB/T 8-1988 方头螺栓 C 级 Square head bolts-Product grade C 3 GB/T 10-1988 沉头方颈螺栓 Flat countersunk square neck bolts 4 GB/T 11-1988 沉头带榫螺栓 Flat countersunk nib bolts 5 GB/T 12-1988 半圆头方颈螺栓 Cup head square neck bolts 6 GB/T 13-1988 半圆头带榫螺栓 Cup head nib bolts 7 GB/T 15-1988 大半圆头带榫螺栓 Cup head nib bolts wi
2、th large head 8 GB/T 22-1976 小六角头导颈螺栓 Bolts, small hexagon head with fit neck 9 GB/T 23-1976 小六角头螺杆带孔螺栓 Bolts, small hexagon head with hole through the shank 10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓 Bolts, small hexagon head with fit neck and hole through the shank 11 GB/T 25-1976 小六角头头部带孔螺栓 Bolts, small hexago
3、n head with holes through the head 12 GB/T 26-1976 小六角头头部带孔导颈螺栓 Bolts, small hexagon head with fit neck and holes through the head 13 GB/T 27-1988 六角头铰制孔用螺栓 A 和 B 级 Hexagon fit bolts-Product grade A and B 14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A 和 B 级 Hexagon fit bolts with Split pin hole on shank-Product gr
4、ade A and B 15 GB/T 29.1-1988 六角头头部带槽螺栓 A 和 B 级 Hexagon bolts with slot on head-Product grade A and B 16 GB/T 29.2-1988 十字槽凹穴六角头螺栓 Cross recessed hexagon bolts with indentation 17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A 和 B 级 Hexagon bolts with split pin hole on shank-Product grade A and B 18 GB/T 31.2-1988 六角头螺
5、杆带孔螺栓 细杆 B 级 Hexagon bolts with split pin hole on shank-Reduced shank-Product grade B 19 GB/T 31.3-1988 六角头螺杆带孔螺栓 细牙 A 和 B 级 Hexagon bolts with split pin hole on shank-Fine pitch thread-Product grade A and B 20 GB/T 32.1-1988 六角头头部带孔螺栓 A 和 B 级 Hexagon bolts with wire holes on head-Product grade A an
6、d B 21 GB/T 32.2-1988 六角头头部带孔螺栓 细杆 B 级 Hexagon bolts with wire holes on head-Reduced shank-Product grade B 22 GB/T 32.3-1988 六角头头部带孔螺栓 细牙 A 和 B 级 Hexagon bolts with wire holes on head-Fine pitch thread-Product grade A and B 23 GB/T 35-1988 小方头螺栓 B 级 Square head bolts with small head-Product grade B
7、24 GB/T 37-1988 T 型槽用螺栓 Bolts for T-Slot 26 GB/T 39-1988 方螺母 C 级 Square nuts-Product grade C 27 GB/T 41-1986 1 型六角螺母 C 级 Hexagon nuts-Style 1-Product grad C 28 GB/T 56-1988 六角厚螺母 Hexagon thick nuts 30 GB/T 62-1988 蝶形螺母 Wing nuts 31 GB/T 63-1988 环形螺母 Lifting nuts 32 GB/T 65-1985 开槽圆柱头螺钉 Slotted chees
8、e head screws 33 GB/T 67-1985 开槽盘头螺钉 Slotted pan head screws 34 GB/T 68-1985 开槽沉头螺钉 Slotted countersunk head screws 35 GB/T 69-1985 开槽半沉头螺钉 Slotted raised countersunk head screws 36 GB/T 70-1985 内六角圆柱头螺钉 Hexagon socket cap head screws 37 GB/T 71-1985 开槽锥端紧定螺钉 Slotted set screws with cone point 38 GB
9、/T 72-1988 开槽锥端定位螺钉 Slotted set screws with cone point 39 GB/T 73-1985 开槽平端紧定螺钉 Slotted set screws with flat point 40 GB/T 74-1985 开槽凹端紧定螺钉 Slotted set screws with cup point 41 GB/T 75-1985 开槽长圆柱端紧定螺钉 Slotted set screws withlong dog point 42 GB/T 77-1985 内六角平端紧定螺钉 Hexagon socket set screws with flat
10、 point 43 GB/T 78-1985 内六角锥端紧定螺钉 Hexagon socket set screws with cone point 44 GB/T 79-1985 内六角圆柱端紧定螺钉 Hexagon socket set screws with dog point 45 GB/T 80-1985 内六角凹端紧定螺钉 Hexagon socket set screws with cup point 46 GB/T 83-1988 方头长圆柱球面端紧定螺钉 Square set screws with long dog point and rounded end 47 GB/T
11、 84-1988 方头凹端紧定螺钉 Square set screws with cup point 48 GB/T 85-1988 方头长圆柱端紧定螺钉 Square set screws with long dog point 49 GB/T 86-1988 方头短圆柱锥端紧定螺钉 Square set screws with short dog point and cone end 52 GB/T 91-1986 开口销 Split pins 53 GB/T 93-1987 标准型弹簧垫圈 Single coil spring lock washers-Normal type 57 GB
12、/T 95-1985 平垫圈 -C 级 Plain washers-Product grade C90 GB/T 794-1993 加强半圆头方颈螺栓 Strengthened cap head square neck bolts 91 GB/T 798-1988 活节螺栓 Eye bolts 92 GB/T 799-1988 地脚螺栓 Eyelet bolts 93 GB/T 800-1988 沉头双榫螺栓 Flat countersunk double nib bolts 94 GB/T 802-1988 组合式盖形螺母 Acorn nuts 95 GB/T 804-1988 球面六角螺母
13、 Hexagon nuts with raised face 96 GB/T 805-1988 扣紧螺母 Tight nuts 97 GB/T 806-1988 滚花高螺母 Knurled nut with collar 98 GB/T 807-1988 滚花薄螺母 Knurled nuts 99 GB/T 808-1988 小六角特扁细牙螺母 Small hexagon thin nuts-Fine pitch thread 100 GB/T 809-1988 嵌装圆螺母 Insert round nuts 101 GB/T 810-1988 小圆螺母 Small round nuts 10
14、2 GB/T 812-1988 圆螺母 Round nuts 103 GB/T 815-1988 端面带孔圆螺母 Round nuts with drilled holes in one face 104 GB/T 816-1988 侧面带孔圆螺母 Round nuts with set pin holes in side 105 GB/T 817-1988 带槽圆螺母 Slotted round nuts 106 GB/T 818-1985 十字槽盘头螺钉 Cross recessed pan head screws 107 GB/T 819-1985 十字槽沉头螺钉 Cross reces
15、sed countersunk head screws 108 GB/T 820-1985 十字槽半沉头螺钉 Cross recessed raised countersunk head screws 109 GB/T 821-1988 方头倒角端紧定螺钉 Square set screws with chamfered end 110 GB/T 822-1988 十字槽圆柱头螺钉 Cross recessed cheese head serews 111 GB/T 823-1988 十字槽小盘头螺钉 Cross recessed small pan head screws 112 GB/T
16、824-1976 圆柱头内花键螺钉 Screws,fluted socket head 113 GB/T 825-1988 吊环螺钉 Eyebolts 114 GB/T 827-1986 标牌铆钉 Rivets for name plate 115 GB/T 828-1988 开槽盘头定位螺钉 Slotted pan head set setscrews with dog point 116 GB/T 829-1988 开槽圆柱端定位螺钉 Slotted setscrews with dog point 117 GB/T 830-1988 开槽圆柱头轴位螺钉 Slotted cheese he
17、ad screws with shoulder 118 GB/T 831-1988 开槽无头轴位螺钉 Slotted shoulder screws 119 GB/T 832-1988 开槽带孔球面圆柱头螺钉 Slotted capstan screws 120 GB/T 833-1988 开槽大圆柱头螺钉 Slotted large cheese head screws 121 GB/T 834-1988 滚花高头螺钉 Knurled thumb screws 122 GB/T 835-1988 滚花平头螺钉 Knurled screws 123 GB/T 836-1988 滚花小头螺钉 K
18、nurled screws with small head 124 GB/T 837-1988 开槽盘头不脱出螺钉 Slotted pan head screws with waisted shank 125 GB/T 838-1988 六角头不脱出螺钉 Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉 Knurled thumb screws with waisted shank 127 GB/T 840-1988 塑料滚花头螺钉 Plastic diamond knurlhead screws 128 GB/T 845
19、-1985 十字槽盘头自攻螺钉 Cross recessed pan head tapping screws 129 GB/T 846-1985 十字槽沉头自攻螺钉 Cross recessed countersunk head tapping screws 130 GB/T 847-1985 十字槽半沉头自攻螺钉 Cross recessed raised countersunk head tapping screws 131 GB/T 848-1985 小垫圈 -A 级 Plain washers-Small series-Product grade A 132 GB/T 849-1988
20、 球面垫圈 Weshers with ball face 133 GB/T 850-1988 锥面垫圈 Washers with cone face 134 GB/T 851-1988 开口垫圈 Washers with split 135 GB/T 852-1988 工字钢用方斜垫圈 Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈 Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈 Tab washers with long tab 138 GB
21、/T 855-1988 双耳止动垫圈 Tab washers with long tab and wing 139 GB/T 856-1988 外舌止动垫圈 External tab washers 140 GB/T 858-1988 圆螺母用止动垫圈 Tab washers for round nut 141 GB/T 859-1987 轻型弹簧垫圈 Single coil spring lock washers,Light type 142 GB/T 860-1987 鞍形弹性垫圈 Curved spring washers 143 GB/T 861.1-1987 内齿锁紧垫圈 Lock
22、washers internal teeth 144 GB/T 861.2-1987 内锯齿锁紧垫圈 Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈 Lock washers external teeth 146 GB/T 862.2-1987 外锯齿锁紧垫圈 Serrated lock washers external teeth 147 GB/T 863.1-1986 半圆头铆钉 ( 粗制 ) Round head rivets-Black 148 GB/T 863.2-1986 小半圆头铆钉 ( 粗制 ) R
23、ound head rivets with small head-Black 149 GB/T 864-1986 平锥头铆钉 ( 粗制 ) Cone head rivets-Black 150 GB/T 865-1986 沉头铆钉 ( 粗制 ) Countersunk head rivets-Black 151 GB/T 866-1986 半沉头铆钉 ( 粗制 ) Oval countersunk head rivets-Black 152 GB/T 867-1986 半圆头铆钉 Round head rivets 153 GB/T 868-1986 平锥头铆钉 Cone head rivet
24、s 154 GB/T 869-1986 沉头铆钉 Countersunk head rivets 155 GB/T 870-1986 半沉头铆钉 Oval countersunk head rivets 156 GB/T 871-1986 扁圆头铆钉 Flat round head rivets 157 GB/T 872-1986 扁平头铆钉 Thin head rivets 158 GB/T 873-1986 扁圆头半空心铆钉 Oval head semi-tubular rivets 159 GB/T 874-1986 120 沉头半空心铆钉 120 degree countersunk
25、head semi-tubular rivets 160 GB/T 875-1986 偏平头半空心铆钉 Thin head semi-tubular rivet 161 GB/T 876-1986 空心铆钉 Tubular rivets 162 GB/T 877-1986 开尾圆锥销 Taper pins with split 163 GB/T 878-1986 螺纹圆柱销 Parallel pins with external thread 164 GB/T 879-1986 弹性圆柱销 Spring-type straight pinsSlotted 165 GB/T 880-1986 带
26、孔销 Pins with split pin hole 166 GB/T 881-1986 螺尾锥销 Taper pins with external thread 167 GB/T 882-1986 销轴 Clevis pins with head 168 GB/T 883-1986 锥销锁紧挡圈 Lock rings with cone pin 169 GB/T 884-1986 螺钉锁紧挡圈 Lock ring with screw 170 GB/T 885-1986 带锁圈的螺钉锁紧挡圈 Lock rings with screw and circlip 171 GB/T 886-19
27、86 轴肩挡圈 Rings for shoulder 172 GB/T 889-1986 1 型非金属嵌件六角锁紧螺母 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 173 GB/T 891-1986 螺钉紧固轴端挡圈 Lock rings at the end of shaft with screw 174 GB/T 892-1986 螺栓紧固轴端挡圈 Lock rings at the end of shaft with bolt 175 GB/T 893.1-1986 孔用弹性挡圈 -A 型
28、Circlips for holes-Type A 176 GB/T 893.2-1986 孔用弹性挡圈 -B 型 Circlips for hole-Type B 177 GB/T 894.1-1986 轴用弹性挡圈 -A 型 Circlips for shaft-Type A 178 GB/T 894.2-1986 轴用弹性挡圈 -B 型 Circlips for shaft-Type B 179 GB/T 895.1-1986 孔用钢丝挡圈 Roundwire snap rings for hole 180 GB/T 895.2-1986 轴用钢丝挡圈 Roundwire snap ri
29、ngs for shaft 181 GB/T 896-1986 开口挡圈 E rings 182 GB/T 897-1988 双头螺柱 bm=1d Double end studs-bm=1d 183 GB/T 898-1988 双头螺柱 bm=1.25d Double end studs bm=1.25d 184 GB/T 899-1988 双头螺柱 bm=1.5d Double end studs bm=1.5d 185 GB/T 900-1988 双头螺柱 bm=2d Double end studs bm=2d 186 GB/T 901-1988 等长双头螺柱 B 级 Double e
30、nd studs (clamping type)-Product grade B 187 GB/T 902.1-1989 手工焊用焊接螺柱 Weld studs for manual welding 188 GB/T 902.2-1989 机动弧焊用焊接螺柱 Weld studs for arc welding 189 GB/T 902.3-1989 储能焊用焊接螺柱 Weld studs for capacitor discharge welding 190 GB/T 921-1986 钢丝锁圈 Round wire circlips 191 GB/T 922-1986 木螺钉技术条件 Sp
31、ecifications for wood screws 192 GB/T 923-1988 盖形螺母 Acorn nuts 193 GB/T 925-1988 轻型六角自锁螺母 Self-locking nuts,hexagon light 194 GB/T 927-1988 球面六角自锁螺母 Self-locking nuts,hexagon sphere 195 GB/T 929-1988 单耳托板自锁螺母 Self-locking nuts,singlelug, anchor 196 GB/T 930-1988 双耳托板自锁螺母 Self-locking nuts,twolug, an
32、chor 197 GB/T 931-1988 角形托板自锁螺母 Self-locking nuts,angle, anchor 198 GB/T 932-1988 气密单耳托板自锁螺母 Self-locking nuts,singlelug, anchor, sealing, 199 GB/T 933-1988 气密双耳托板自锁螺母 Self-locking nuts,twolug, anchor, sealing 200 GB/T 937-1988 成组游动托板自锁螺母 Self-locking nuts, anchor, floating,Gang channel 201 GB/T 938
33、-1988 游动自锁螺母 Self-locking nuts, floating 202 GB/T 939-1988 单耳托板自锁螺母保护罩 Boots for self-locking nuts, singlelug, anchor 203 GB/T 940-1988 双耳托板自锁螺母保护罩 Boots for self-locking nuts,twolug, anchor 204 GB/T 941-1988 角形托板自锁螺母保护罩 Boots for self-locking nuts,angle, anchor 205 GB/T 943-1988 自锁螺母技术条件 Procuremen
34、t specification for self-locking nuts 206 GB/T 945-1976 十字槽球面中柱头螺钉 Screws,cross recessed,thin raised cheese head 207 GB/T 946-1988 开槽球面圆柱头轴位螺钉 Slotted raised cheese head with shoulder 208 GB/T 947-1988 开槽球面大圆柱头螺钉 Slotted large raised cheese head screws 209 GB/T 948-1988 开槽沉头不脱出螺钉 Slotted countersunk
35、 head screws with waisted shank 210 GB/T 949-1988 开槽半沉头不脱出螺钉 Slotted raised countersunk head screws with waisted shank 211 GB/T 950-1986 十字槽圆头木螺钉 Cross recessed round head wood screws 212 GB/T 951-1986 十字槽沉头木螺钉 Cross recessed countersunk head wood screws 213 GB/T 952-1986 十字槽半沉头木螺钉 Cross recessed ra
36、ised countersunk head wood screws 214 GB/T 953-1988 等长双头螺柱 C 级 Double end studs (clamping type)-Product grade C 215 GB/T 954-1986 120 沉头铆钉 120degree countersunk head rivets 216 GB/T 955-1987 波形弹性垫圈 Wave spring washers 217 GB/T 956.1-1987 锥形锁紧垫圈 Countersunk external toothed lock washers 218 GB/T 956.
37、2-1987 锥形锯齿锁紧垫圈 Countersunk serrated external toothed lock washers 219 GB/T 959.1-1986 挡圈技术条件 - 弹性挡圈 Specifications for ringCirclips 220 GB/T 959.2-1986 挡圈技术条件 - 钢丝挡圈 Specifications for ringRound wire snap rings 221 GB/T 959.3-1986 挡圈技术条件 - 切制挡圈 Specifications for ringCutting rings 222 GB/T 960-1986
38、 夹紧挡圈 Grip rings 223 GB/T 961-1988 单耳托板自锁螺母垫片 Spacers for self-locking nuts,singlelug, anchor 224 GB/T 962-1988 双耳托板自锁螺母垫片 Spacers for self-locking nuts,twolug, anchor 225 GB/T 963-1988 角形托板自锁螺母垫片 Spacers for self-locking nuts,angle, anchor 226 GB/T 973-1976 十字槽扁圆头螺钉 Screws,cross recessed,oval head
39、227 GB/T 974-1976 十字槽 120 半沉头螺钉 Screws,cross recessed,120raised countersunk head 228 GB/T 975-1986 管状铆钉 Pipe type rivets 229 GB/T 1007-1976 小六角较扁螺母 Small hexagon medium thin nuts 230 GB/T 1009-1978 螺母专用技术条件 Specified specifications for nuts 231 GB/T 1011-1986 大扁圆头铆钉 Truss head rivets 232 GB/T 1012-1
40、986 120 半沉头铆钉 120degree oval countersunk rivets 233 GB/T 1013-1986 平锥头半空心铆钉 Cone head semi-tubuler rivets 234 GB/T 1014-1986 大扁圆头半空心铆钉 Truss head semi-tubuar rivets 235 GB/T 1015-1986 沉头半空心铆钉 Countersunk head semi-tublar rivets 236 GB/T 1016-1986 无头铆钉 Headless rivets 237 GB/T 1017-1978 铆钉专用技术条件 Spec
41、ified specifications for rivets 238 GB/T 1021-1976 角形垂直单耳止动垫圈 Lock washers with angular upturn tab perpendicular to the lug 239 GB/T 1022-1976 角形单耳止动垫圈 Lock washers with angular upturn tab in line to the lug 240 GB/T 1023-1976 角形垂直外舌止动垫圈 Lock washers with angular upturn tab perpendicular to the exte
42、rnal tab 241 GB/T 1024-1976 角形外舌止动垫圈 Lock washers with angular upturn tab in line to the external tab 242 GB/T 1030-1988 内球面垫圈 Inner sphere washers 243 GB/T 1047-1995 管道元件的公称通径 Nominal size for pipe components 244 GB/T 1048-1990 管道元件公称压力 Nominal pressure for pipe components 245 GB/T 1095-1979 平键 键和键
43、槽的剖面尺寸 Parallel keys-Dimensions of cross sections and keyways 246 GB/T 1096-1979 普通平键 型式尺寸 Plain parallel keys-Types and dimensions 247 GB/T 1097-1979 导向平键 型式尺寸 Feather keys-Types and dimensions 248 GB/T 1098-1979 半圆键 键和键槽的剖面尺寸 Semi-circular (Woodruff) keys-Dimensions of cross sections and keyways 2
44、49 GB/T 1099-1979 半圆键 型式尺寸 Woodruff keys-Types and dimensions 250 GB/T 1144-1987 矩形花键尺寸、公差和检验 Straight-sided splineDimensions tolerances and verification 251 GB/T 1168-1976 螺柱技术条件 Studs-Technical requirements 252 GB/T 1228-1991 钢结构用高强度大六角头螺栓 High strength bolts with large hexagon head for steel stru
45、ctures 253 GB/T 1229-1991 钢结构用高强度大六角螺母 High strength large hexagon nuts for steel structures 254 GB/T 1230-1991 钢结构用高强度垫圈 High strength plain washers for steel structures 255 GB/T 1231-1991 钢结构用高强度大六角头螺拴、大六角螺母、垫圈技术条件 Specifications of high strength bolts with large hexa-gon head, large hexagon nuts,
46、 plain washers for steel structures 256 GB/T 1237-1988 紧固件的标记方法 Designation system for fasteners 257 GB/T 1337-1988 六角自锁螺母 Self-locking nuts,hexagon 258 GB/T 1338-1988 小六角扁自锁螺母 Self-locking nuts,reduced hexagon oblate 259 GB/T 1339-1988 小六角自锁螺母 Self-locking nuts,reduced hexagon 260 GB/T 1340-1988 成组
47、游动托板自锁螺母支架 Supports for self-locking nuts,anchor floating,Gang channel 261 GB/T 1356-1988 淅开线圆柱齿轮 基本齿廓 Basic rack tooth profile of involute cylindrical gears 262 GB/T 1357-1987 渐开线圆柱齿轮模数 Modules of involute cyindrical gears 263 GB/T 1563-1979 楔键 键和键槽的剖面尺寸 Taper keys-Cross section dimensions of keys
48、and keyways 264 GB/T 1564-1979 普通楔键 型式尺寸 Taper keys for general use-Types and dimensions 265 GB/T 1565-1979 钩头楔键 型式尺寸 Gib-head taper keys-Types and dimensions 266 GB/T 1566-1979 薄型平键 键和键槽的剖面尺寸 Thin flat keys-Cross section dimensions and keyways 267 GB/T 1567-1979 薄型平键 型式尺寸 Thin flat keys-Types and dimensions 277 GB/T 2672-1986 内六角花形盘头螺钉 Hexagon lobular socket pan head screws