《【BS英国标准】BS EN 13744-2004 Surfaces for sports areas. Procedure for accelerated ageing by immersion in hot water.doc》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 13744-2004 Surfaces for sports areas. Procedure for accelerated ageing by immersion in hot water.doc（9页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN13744:2004Surfaces for sports areas Procedure for accelerated ageing by immersion in hot waterThe European Standard EN 13744:2004 has the status of aBritish StandardICS 97.150; 97.220.10 BS EN 13744:2004National forewordThis British Standard is the official English language ver
2、sion ofEN 13744:2004.The UK participation in its preparation was entrusted to Technical CommitteePRI/57, Surfaces for sports areas, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any enquiries on the interpretation, or
3、 proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement inte
4、rnational or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purp
5、ort to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Commi
6、ttee on13 October 2004 BSI 13 October 2004ISBN 0 580 44597 6Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amd. No.DateComme
7、ntsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 13744October 2004ICS 97.150; 97.220.10English versionSurfaces for sports areas - Procedure for accelerated ageing by immersion in hot waterSols sportifs - Mthode de vieillissement acclr par immersion dans leau c
8、haudeSportbden - Verfahren der beschleunigten Alterung durchEintauchen in heies WasserThis European Standard was approved by CEN on 29 July 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a
9、national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in
10、 any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Fin
11、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI ON EUR O P
12、 I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 13744:2004: EEN 13744:2004 (E)ContentsPageForeword.31Scope .42Principle .43Apparatus .44T
13、est pieces .45Procedure .46Comparison tests.57Calculation and expression of results.58Test report .55ForewordThis document (EN 13744:2004) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI.This European Standard shall be given th
14、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005.It is one of two standards for procedures for ageing surfaces for sports areas. The other stan
15、dard in this series has the following title:EN 13817, Surfaces for sports areas Procedures for accelerated ageing by exposure to hot airAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au
16、stria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.1ScopeThis document describes a
17、 procedure for subjecting test pieces taken from surfaces for sports areas to accelerated ageing by immersion in hot water. Test pieces are aged to permit a comparison of their physical characteristics before and after ageing in accordance with European Standard test methods for surfaces for sports
18、areas.This method is suitable for ageing all types of sports surfaces, except for wooden surfaces, using test pieces in the laboratory, but is primarily intended for ageing polymeric surfaces. The procedure allows a measure of the effect on the physical characteristics of the sports surface due to e
19、xposure to water at elevated temperatures to be made.NOTEResults from tests on materials which exhibit temporary changes in properties due to moisture should be interpreted with caution.2PrincipleTest pieces are exposed to water at an elevated temperature to permit selected physical characteristics
20、of the surface to be assessed before and after test.3Apparatus3.1Water bath, capable of being maintained at (70 2) C.3.2Small weights, to assist with immersion if necessary.4Test piecesSelect, prepare and condition the test piece(s) in accordance with the appropriate method of test.Test pieces shall
21、 be such that no mechanical, chemical or heat treatment will be required after their removal from the water bath.Any material used for marking test pieces shall not be applied in any critical area of the test piece and shall not damage the surface or be destroyed during ageing.NOTEWherever possible,
22、 marking should be carried out after ageing of the test piece.5ProcedureImmerse test pieces in the water bath (3.1) maintained at a temperature of (70 2) C, the test pieces being freely exposed to the ageing environment on all sides. If necessary, use the small weights (3.2) to submerge the test pie
23、ces in the water bath.Leave the test pieces in the water bath for (336 2) h.Remove the test pieces from the water bath and condition them together with an un-aged sample for not less than 16 h and for no more than 6 d in a relaxed condition in accordance with the test method for the particular chara
24、cteristic being assessed.NOTESimultaneous ageing of different test pieces in the same water bath should be avoided, to prevent migration of anti-degradants or plasticizers, etc.6Comparison testsTo compare properties before and after accelerated ageing, carry out tests on un-aged test pieces at the s
25、ame time and under the same conditions as those on test pieces having been subjected to accelerated ageing. Only compare test pieces of similar dimensions and having approximately the same exposed areas.7Calculation and expression of resultsCalculate the results as specified by the appropriate metho
26、d of test. If required, calculate the percentage change in the property using the following expression:C = A O 100OwhereCis the percentage change in the property;Ais the aged value of the property, e.g. % impact absorption;Ois the un-aged value of the property.8Test reportThe test report shall inclu
27、de the following:a) reference to this document, i.e. EN 13744:2004;b) reference to the procedure used to select the test pieces and determine their characteristics, e.g. aEuropean Standard test method;c) complete identification of the surface tested including manufacturers reference, type and depth
28、of supporting layers, and method of attachment and previous history;d) physical characteristics determined, with their values before and after ageing, and, if required, their percentage change, calculated in accordance with Clause 7;e)individual test results, if required.BS EN13744:2004BSI389 Chiswi
29、ck High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparingBritish Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amend
30、ment or revision. Users ofBritish Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard woul
31、d inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest
32、 editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001.Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are alsoavailable from the BSI website at http:/www.bsi-.In response t
33、o orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Li
34、brary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kep
35、t up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.Email: membershipbsi-.Information regarding online access to Bri
36、tish Standards via British StandardsOnline can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bod
37、ies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free
38、use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.Email: copyrightbsi-.国内外标准大全豆丁网国内外标准下载地址 http:/