《【BS标准word原稿】BS EN 12006-3-1999 Non-active surgical implants. Particular requirements for cardiac and vascular implants. Endovascular devices.doc》由会员分享，可在线阅读，更多相关《【BS标准word原稿】BS EN 12006-3-1999 Non-active surgical implants. Particular requirements for cardiac and vascular implants. Endovascular devices.doc（15页珍藏版）》请在三一文库上搜索。
1、豆丁网：http:/ STANDARDNon-active surgical implants Particular requirements for cardiac and vascular implants Part 3: Endovascular devicesThe European Standard EN 12006-3:1998 has the status of aBritish StandardICS 11.040.40| BS EN12006-3:1999|Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:48
2、:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 12006-3:1999National forewordThis British Standard is the English language version of EN 12006-3:1998.The UK participation in its preparation was entrusted to Technical Committe
3、e CH/23, Cardiovascular implants, dialysis systems and oxygenators, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related i
4、nternational and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be foun
5、d in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are r
6、esponsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover.Licensed Copy: sheffieldun sheffieldun,
7、 na, Sat Oct 28 14:48:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIAmd. No.DateText affectedThis British Standard, having been prepared under the direction of the Health and Environment Sector Committee, was published under the authority of the StandardsCommittee and comes into effect on 15 March 19
8、99BSI 03-1999ISBN 0 580 30888 XAmendments issued since publicationEUROPEAN STANDARDEN 12006-3NORME EUROPE ENNEEUROPA ISCHE NORMNovember 1998ICS 11.040.40Descriptors: medical devices, medical equipment, surgical implants, cardiac valves, vascular stents, filters, specifications, corrosion resistance,
9、 fatigue life, dimensions, design, materials, manufacturing, sterilization, packing, instructionsEnglish versionNon-active surgical implants Particular requirements for cardiac and vascular implants Part 3: Endovascular devicesImplants chirurgicaux non-actifs Exigences particulie res relatives aux i
10、mplants cardiaques et vasculaires Partie 3: Dispositifs endovasculairesNichtaktive chirurgische Implantate Besondere Anforderungen an Herz- und Gefa implantate Teil 3: Endovaskula re ImplantateLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:48:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIT
11、his European Standard was approved by CEN on 8 November 1998.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refer
12、ences concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member int
13、o its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sp
14、ain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CE
15、N nationalMembers.Ref. No. EN 12006-3:1998 EPage 7EN 12006-3:1998BSI 03-1999ForewordThis European Standard has been prepared byTechnical Committee CEN/TC 285, Non-active surgicalContentsPageLicensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:48:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIimpl
16、ants, the Secretariat of which is held by NNI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1999, and conflicting national standards shall be withdrawn atthe latest by May 1999.This European
17、 Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex C, which is an integral part of this standard.There are thr
18、ee levels of European Standards dealing with non-active surgical implants. These are as follows, with level 1 being the highest:Level 1: General requirements for non-active surgical implants.Level 2: Particular requirements for families of non-active surgical implants.Level 3: Specific requirements
19、for types of non-active surgical implants.This standard is a level 2 standard and contains requirements that apply to all non-active surgical implants in the family of vena cava filters and vascular stents.The level 1 standard contains requirements that apply to all non-active surgical implants.Leve
20、l 3 standards contain requirements that apply to specific types of implants within a family.To address all requirements, it is necessary to start with a standard of the lowest available level.References can also be found in annex A of this standard.According to the CEN/CENELEC Internal Regulations,
21、the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Ki
22、ngdom.Foreword 21Scope 32Normative references 33Definitions 34Intended performance 35Design attributes 36Materials 37Design evaluation 48Manufacturing 59Sterilization 510Packaging 511Information supplied by themanufacturer 5Annex A (informative) Bibliography 6Annex B (informative) Animal studies wit
23、hstents 6Annex C (informative) Clauses of this European Standard addressing essential requirements or other provisions of EUDirectives 7Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 14:48:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSIIntroductionThis European Standard, in addition to EN ISO
24、14630, provides a method to demonstrate compliance with the relevant Essential Requirements as outlined in general terms in Annex 1 of the Council Directive 93/42/EEC of14 June 1993 concerning medical devices, as they apply to endovascular devices.1 ScopeThis European Standard specifies particular r
25、equirements for endovascular devices.With regard to safety, this standard gives, in addition to EN ISO 14630, requirements for intended performance, design attributes, materials, design evaluation, manufacturing, sterilization, packaging and information supplied by the manufacturer.NOTE 1 Vascular o
26、ccluders are not addressed in this standard. For the time being the requirements as stated inEN ISO 14630:1997 apply for these products.NOTE 2 Due to the variations in the design of the implants covered by this standard and in some cases due to the relatively recent development of some of these impl
27、ants, acceptable standardized in vitro tests and long term results of clinical trials are not always available.Where no test method is described in this standard a complete description of the validated test method and sample preparation procedure used should be documented by the manufacturer. With r
28、egard to design evaluation, where a specific standardized test is not described, guidance is given by referring to current scientific literature (see annex A). This standard aims to ensure that manufacturers will address all aspects of design evaluation that relate to the safety of the product. As f
29、urther scientific and clinical data become available, appropriate revision of the standard will be necessary.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in
30、the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to
31、applies.EN ISO 14630:1997, Non-active surgical implants General requirements.(ISO 14630:1997)ISO 10555-4, Sterile, single-use intravascular catheters Part 4: Balloon dilatation catheters.3 DefinitionsFor the purpose of this standard the definitions ofEN ISO 14630 apply together with the following.3.
32、1vascular stentimplantable expandable tubular structure supporting a vascular conduit3.2vena cava filterimplantable expanding filtering device to be inserted into the vena cava3.3stented grafta combination of one or more stents and a tubular graft4 Intended performanceThe requirements of EN ISO 1463
33、0:1997, clause 4 apply.5 Design attributesThe requirements of EN ISO 14630:1997, clause 5 apply together with the following:a) oxidation-potential, the possibility of crevice corrosion, passivation level (see 7.1.3) over the relevant parts;b) with regard to wear: fretting corrosion (see 7.1.2);c) in
34、terface between implant and body (see clause 7):1) fixation hooks if present;2) relative movement between implant and tissue;3) forces exerted by the device on the surrounding tissue;4) forces required to deform the device if the deformation is permanent;d) expected ingrowth, penetration, perforatio
35、n, tilting and migration (see clause 7);e) effects by flow pattern and release of ions(see 7.1.3);f) introduction and delivery systems (see 7.1.4);g) geometry (see clause 7).6 MaterialsThe requirements of EN ISO 14630:1997, clause 6 shall apply.Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28
36、14:48:38 GMT+00:00 2006, Uncontrolled Copy, (c) BSI7 Design evaluationThe requirements of EN ISO 14630:1997, clause 7 shall apply together with the following.NOTE The effects of MRI on the implant should be evaluated during the risk analysis.7.1 GeneralWhere no test method is described in this stand
37、ard, description of the validated test method and sample preparation used in the study shall be documented by the manufacturer. The need for a reference device shall be considered. The method chosen including thechoice of the reference device shall be justified.Data are required for a finite element
38、 or other stress analysis that identifies the peak stresses in the device when subjected to a worst-case physiological load. The amounts of residual stress shall be determined and accounted for when calculating safety factors.7.1.1 Structural integrity testingThe anticipated deformation profile shal
39、l be determined. For self expanding stents the forces exerted by the device on the arterial wall shall be determined.7.1.2 Fatigue analysisAn in-depth analysis of the implants fatigue resistance shall be performed to ensure that the arterial/venous implant conditions to which the device will be subj
40、ected will not result in device failure.When in vitro-testing is used as the primary method to evaluate fatigue, analysis to determine the device fatigue at 10 years equivalent real time should be conducted on a statistically significant sample of devices and dynamically cycled over simulated vessel
41、 conditions.NOTE Guidance can be found in A.1.7.1.3 Oxidation potentialsThe implant shall undergo potential measurement.NOTE 1 Guidance can be found in A.2.NOTE 2 Where several materials are used the manufacturer should provide proof of their compatibility in terms of oxidation potential.7.1.4 Devic
42、e/catheter systemThe device/catheter system shall be tested to demonstrate that it can deliver the device to the intended location and that the device is not adversely affected by the catheter. Where a balloon catheter is used it shall comply with ISO 10555-4.7.1.5 SurfaceThe implant shall be free f
43、rom defects when examined as follows:a) examine the implant visually with normal sight for process or surface defects;b) examine the surface, hooks and other appropriate aspects of the stent with a magnifier for process or surface defects;NOTE 1 Magnification of 32.5 to 5 is recommended.c) examine p
44、articularly exposed areas of the implant under magnification greater than that used in b). NOTE 2 Magnification of 320 to 50 is recommended.7.2 Stents (self expandable and balloon expandable)7.2.1 DimensionsAt least the following dimensions shall be measured: a) inner diameter after expansion in nominal conditions. The measured values for internal measurements shall be rounded down to thenext 0.1 mm (see clause 11);b) outer diameter after expansion in nominal conditions. The measured values for external measurements shall be rounded up t