《【BS英国标准word原稿】BS EN 10168-2004 钢产品.检查文件.信息和描述表.doc》由会员分享，可在线阅读，更多相关《【BS英国标准word原稿】BS EN 10168-2004 钢产品.检查文件.信息和描述表.doc（19页珍藏版）》请在三一文库上搜索。
1、 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等情况，请大家通过论坛消息与我联系。BRITISH STANDARD BS EN10168:2004-,-,-Steel products Inspection documents List of information and descriptionThe European Standard EN 10168:2004 has the status of aBritish StandardICS 01.110; 77.080.20; 77.140.01 ，如果你需要更多标准可以到 如果你购买的文档存在缺页、字迹模糊、乱码等
2、情况，请大家通过论坛消息与我联系。Copyright European Committee for StandardizationProvided by IHS under license with CENNo reproduction or networking permitted without license from IHSNot for ResaleBS EN 10168:2004National forewordThis British Standard is the official English language version ofEN 10168:2004.The UK
3、participation in its preparation was entrusted to Technical Committee ISE/5, Technical delivery conditions, classification and designation of steels, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any enquiries on the
4、interpretation, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards wh
5、ich implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publica
6、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.-,-,-This British Standard was published under the authority of the Standards Po
7、licy and Strategy Committee on24 June 2004 BSI 24 June 2004ISBN 0 580 43982 8Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover.The BSI copyright notice displayed in this document indicates when the do
8、cument was last issued.Amd. No.DateCommentsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 10168June 2004ICS 01.110; 77.080.20; 77.140.01English versionSteel products - Inspection documents - List of information and descriptionProduits en acier - Documents de co
9、ntrle - Liste et description des informationsStahlerzeugnisse - Prfbescheinigungen - Liste undBeschreibung der AngabenThis European Standard was approved by CEN on 19 March 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E
10、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (Engli
11、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czec
12、h Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN
13、 DE NOR M A L I S A TI ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 10168:2004: E-,-,-,-,-EN 10168:2004 (E)ContentspageForew
14、ord. 31Scope . 42Normative references . 43Terms and definitions . 44Principles . 45Information description. 52Annex A (normative) List of the section designations and their corresponding translations. 11-,-,-EN 10168:2004 (E)ForewordThis document (EN 10168:2004) has been prepared by Technical Commit
15、tee ECISS/TC 9 “Technical conditions of delivery and quality control”, the secretariat of which is held by IBN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting nation
16、al standards shall be withdrawn at the latest by December 2004.Annex A is normative.This document includes a Bibliography.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium
17、, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.Copyright European Committee for Standardizat
18、ionProvided by IHS under license with CENNo reproduction or networking permitted without license from IHS3Not for ResaleEN 10168:2004 (E)1ScopeThis European Standard lists the information that may be communicated in and includes a brief description of the inspection documents of steel products as de
19、scribed in EN 10204.By laying down standardized designations and definitions for information likely to appear in inspection documents and by introducing code numbers for each of the designated sections, this European Standard intends to contribute to the elimination of communication difficulties in
20、European trade.-,-,-NOTEThese designations may also be used in delivery documents.2Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publication
21、s are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendmen
22、ts).EN 10204, Metallic products - Types of inspection documents.3Terms and definitionsFor the purposes of this European Standard, the terms and definitions given in EN 10204 apply.4PrinciplesAll types of inspection documents specified in EN 10204 have as a common element groups of information which
23、make it possible to assign them clearly to the corresponding products supplied (see Table 1, information groups A and B).All inspection documents, except for the type 2.1 document Declaration of compliance with the order, contain information on non-specific or specific tests carried out on the basis
24、 of the relevant product specification (see Table1, information groups C and D).In all types of inspection documents a statement on the conformity of the products delivered with the requirements of the order shall be included (see Table 1, information group Z).The organization responsible for supply
25、ing an inspection document may vary the sequence and the lay-out of the information given in clause 5 and Tables 2 to 5. It may also delete unnecessary sections depending on the product.The code number for the different sections in Tables 2 to 5 is unique. Other numbers shall not be used.The section
26、 designations given in Tables 2 to 5 should be given in the relevant sections of the inspection documents. They may be abbreviated if no misunderstanding is caused (e.g. direction instead of direction of the test piece).4If there is not enough room in a section for the required information, a refere
27、nce to a supplement or a free section in the inspection document may be used for the section in question. In this case, the information shall be given in the supplement or in the free section under the corresponding code number.Copyright European Committee for StandardizationProvided by IHS under li
28、cense with CENNo reproduction or networking permitted without license from IHSNot for ResaleEN 10168:2004 (E)5Information descriptionThe inspection documents contain the information groups listed in Table 1. Among these information groups, a distinction is made between information sections having sp
29、ecific code numbers and information sections having code numbers which can be freely used.The specific code numbers are given in Tables 2 to 5, column 1. The title of each section in the second column of these tables indicates as precisely as possible the information to be included. The third column
30、 of Tables 2 to 5 contains comments explaining and specifying the subject of the sections.The code numbers which may be freely used as given in Table 1 and Tables 2 to 5 are available for supplementary information supplied by the originator of the document.-,-,-Table 1 Information groups and summary
31、 of their subdivisionSymbolInformation group onSpecific sectionsAvailable sectionsSee Tablefrom - tofrom - toACommercial transactions and parties involvedA 01 - A 09A 10 - A 992BDescription of productsB 01 - B 13B 14 - B 993CInspectionGeneral information Tensile test Hardness testNotched-bar impact
32、testOther mechanical testsChemical composition and steelmaking processC 00 - C 03C 10 - C 13C 30 - C 32C 40 - C 43C 70 - C 92C 04 - C 09C 14 - C 29C 33 - C 39C 44 - C 49C 50 - C 69C 93 - C 994DOther testsD 01 - D 50D 51 - D 995ZValidationZ 01 - Z 04Z 05 - Z 995Copyright European Committee for Standa
33、rdizationProvided by IHS under license with CENNo reproduction or networking permitted without license from IHS5Not for Resale-,-,-EN 10168:2004 (E)6Table 2 Code numbers and designations of the sections of information group A Commercial transactions and parties involvedNoSection designationCommentsA
34、 01A 02A 03A 04A 05A 06A 07A 08A 09A 10 to A 99Manufacturers worksType of inspection documentDocument numberManufacturers markOriginator of the inspection documentCustomer consigneePurchasers order number and, where applicable, item numberManufacturers works order numberCustomer article numberSupple
35、mentary informationName and address of the works where the products were manufactured.As defined in EN 10204.Number fixed by the originator of the document. This document number may be followed by a figure corresponding to the page number in the case of an inspection document comprising several page
36、s.Symbol for identification of the manufacturer which is used for marking the products instead of the manufacturers name.This may be an inspection organization or the qualified department of the manufacturing works.Name and, if necessary, address either of the customer, the consignee or the consigne
37、e of the certificate, this information being referred to asA 06.1, A 06.2 and A 06.3.Order number, item number and, if necessary, the date.Order number and, if necessary, the date or the acknowledgement number.Reference number by the customer to the products to be supplied. This article number is no
38、t a mandatory information to be given by the customer at the time of ordering.Available for information on commercial transactions and parties involved.Copyright European Committee for StandardizationProvided by IHS under license with CENNo reproduction or networking permitted without license from I
39、HSNot for ResaleEN 10168:2004 (E)-,-,-Table 3 Code numbers and designations of the sections of information group B Description of products to which the inspection documents applyNoSection designationCommentsB 01B 02B 03B 04B 05B 06B 07B 08B 09 to B 11B 12B 13B 14 to B 99ProductSteel designationAny s
40、upplementary requirementsProduct delivery conditionReference (heat) treatment of samplesMarking of the productIdentification of the productNumber of piecesProduct dimensionsTheoretical massActual massSupplementary informationDescription of the product form (e.g. : heavy plate, section, wide flat, tu
41、be, hollow section, etc.) and, where appropriate, surface condition, with reference to the dimensional standard, if applicable.Steel name or number and additional symbols and the product specification for the steel.This section is for indicating special requirements, agreed at the time of ordering, not appearing in sections B 01 and B 02.