《【英国标准word原稿】BS EN 1301-3-1997 铝和铝合金 拉制线材 第3部分：尺寸和公差.doc》由会员分享，可在线阅读，更多相关《【英国标准word原稿】BS EN 1301-3-1997 铝和铝合金 拉制线材 第3部分：尺寸和公差.doc（13页珍藏版）》请在三一文库上搜索。
1、豆丁网：http:/ STANDARDAluminium and aluminium alloys Drawn wirePart 3. Tolerances on dimensionsThe European Standard EN 1301-3 : 1997 has the status of aBritish StandardICS 77.150.10| BS EN1301-3 : 1997|第 13 页 共 13 页豆丁网：http:/ Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Oct 16
2、13:32:21 BST 2006, Uncontrolled Copy, (c) BSI|NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 1301-3 : 1997National forewordThis British Standard is the English language version of EN 1301-3 : 1997. Together with Parts 1 and 2, it supersedes BS 1475 : 1972.The UK particip
3、ation in its preparation was entrusted to Technical Committee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep
4、the UK interests informed; monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publicati
5、ons referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using theFind facility of the BSI Standards Electronic Catalogue.Compliance with a British Standard does not of itself confer immunity from lega
6、l obligations.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover.Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Oct 16 13:32:21 BST 2006, Uncontrolled Copy, (c) BSIAmd. No
7、.DateText affectedThis British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1997BSI 1997ISBN 0 580 28635 5Amendments issued since publicationEUROPEAN STANDARDEN 1301-3
8、NORME EUROPE ENNEEUROPA ISCHE NORMJuly 1997ICS 77.150.10Descriptors: Aluminium, aluminium alloys, wire, drawn products, cold drawn products, dimensional tolerancesEnglish versionAluminium and aluminium alloys Drawn wire Part 3: Tolerances on dimensionsAluminium et alliages daluminium Fil e tire Part
9、ie 3: Tole rances sur dimensionsAluminium und Aluminiumlegierungen Gezogene Dra hteTeil 3: GrenzabmaeLicensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Oct 16 13:32:21 BST 2006, Uncontrolled Copy, (c) BSIThis European Standard was approved by CEN on 1997-07-03. CEN members
10、 are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application t
11、o the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same s
12、tatus as the official versions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.CENEuropean Committee for Sta
13、ndardization Comite Europe en de Normalisation Europa isches Komitee fu r NormungCentral Secretariat: rue de Stassart 36, B-1050 Brussels1997 CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN nationalMembers.Ref. No. EN 1301-3 : 1997 EPage 2EN 1301-3 : 1997Fore
14、wordThis European Standard has been prepared byTechnical Committee CEN/TC 132, Aluminium andContentsPagealuminium alloys, the Secretariat of which is held byAFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
15、 the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998.Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4, Wires and drawing stock, to prepare the following standard:EN 1301-3 Aluminium and aluminium alloys
16、 Drawn wire Part 2: Tolerances on dimensionsThis standard is a Part of a set of three standards. The other standards deal with:EN 1301-1 Aluminium and aluminium alloys Drawn wire Part 1: Technical conditions for inspection and deliveryEN 1301-2 Aluminium and aluminium alloys Drawn wire Part 2: Mecha
17、nical propertiesAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherla
18、nds, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Foreword 21 Scope 32 Normative references 33 Tolerances on dimensions 33.1 Round wire 33.2 Square and hexagonal wire 33.3 Rectangular wire 3Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Oct 16 13
19、:32:21 BST 2006, Uncontrolled Copy, (c) BSIBSI 1997Page 3EN 1301-3 : 19971 ScopeThis Part of EN 1301 specifies the tolerances on dimensions of aluminium and aluminium alloy drawn wire for general engineering applications includingrivet manufacture (except aeronautical rivets), covering diameters, th
20、icknesses or widths across flats up to and including 20 mm.It applies to drawn wires, except for welding and electrical purposes.It does not apply to drawing stock.2 Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. These norm
21、ative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard onlywhen incorporated in it by amendment or revision. For undated refer
22、ences the latest edition of the publication referred to applies.EN 1301-1 Aluminium and aluminium alloys Drawn wire Part 1: Technical conditions for inspection and delivery3 Tolerances on dimensionsThe conditions for the sampling and the measurement of dimensions shall be in accordance with EN 1301-
23、1.The tolerances on dimensions of drawn wires depend on its cross-section. They are specified in tables 1 to 3.All dimensions and tolerances are specified in millimetres.Table 1. Tolerances for round wireDimensions in millimetresSpecified diameterToleranceOverUp to and includingGeneral purpose wireR
24、ivet wire10,0202 0,03130,0302 0,04360,0402 0,056100,0502 0,0610150,0702 0,0815200,1102 0,123.1 Round wireThe ovality, defined as the difference between the maximum and the minimum diameter measured on a same cross-section, shall not exceed 50 % of the total tolerance.3.2 Square and hexagonal wireTab
25、le 2. Tolerances for square and hexagonal wireDimensions in millimetresWidth across flatsToleranceOverUp to and including30,04360,056100,0710150,1015200,14Deviations from the regular polygonal shape are included in the specified tolerances. Distortions of the cross-section due to winding or unwindin
26、g operations are not covered by this standard.Table 3. Tolerances for rectangular wireDimensions in millimetresThickness or widthToleranceOverUp to and includingThicknessWidth10,030,04130,040,05360,050,076100,070,1010150,100,1415200,140,183.3 Rectangular wireLicensed Copy: Institute Of Technology Ta
27、llaght, Institute of Technology, Mon Oct 16 13:32:21 BST 2006, Uncontrolled Copy, (c) BSIDeviations from the rectangular shape are included in the specified width tolerances. Distortions of thecross-section owing to winding or unwinding are not covered by this standard.BSI 1997BSI389 Chiswick High R
28、oadLondonW4 4AL| BSI British Standards Institution| BSI is the independent national body responsible for preparing British Standards. It| presents the UK view on standards in Europe and at the international level. It is| incorporated by Royal Charter.| Revisions| British Standards are updated by ame
29、ndment or revision. Users of British Standards| should make sure that they possess the latest amendments or editions.| It is the constant aim of BSI to improve the quality of our products and services. We| would be grateful if anyone finding an inaccuracy or ambiguity while using this| British Stand
30、ard would inform the Secretary of the technical committee responsible,| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.| Fax: 020 8996 7400.| BSI offers members an individual updating service called PLUS which ensures that| subscribers automatically receive the late
31、st editions of standards.| Buying standards| Orders for all BSI, international and foreign standards publications should be| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.| In response to orders for international standards, it is BSI policy to supply the BSI| implementation
32、of those that have been published as British Standards, unless| otherwise requested.| Information on standards| BSI provides a wide range of information on national, European and international| standards through its Library and its Technical Help to Exporters Service. Various| BSI electronic informa
33、tion services are also available which give details on all its| products and services. Contact the Information Centre. Tel: 020 8996 7111.| Fax: 020 8996 7048.| Subscribing members of BSI are kept up to date with standards developments and| receive substantial discounts on the purchase price of stan
34、dards. For details of| these and other benefits contact Membership Administration. Tel: 020 8996 7002.| Fax: 020 8996 7001.| Copyright| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of| the publications of the international standardization bodies. Except as per
35、mitted| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,| stored in a retrieval system or transmitted in any form or by any means electronic,| photocopying, recording or otherwise without prior written permission from BSI.| This does not preclude the free use, in the c
36、ourse of implementing the standard, of| necessary details such as symbols, and size, type or grade designations. If these| details are to be used for any other purpose than implementation then the prior| written permission of BSI must be obtained.| If permission is granted, the terms may include royalty payments or a licensing| agreement. Details and advice can be obtained from the Copyright Manager.| Tel: 020 8996 7070.|Licensed Copy: Institute Of Technology Tallaght, Institute of Technology, Mon Oct 16 13:32:21 BST 2006, Uncontrolled Copy, (c) BSI | |国内外标准大全豆丁网国内外标准下载地址 http:/