《（BS英国标准）BS EN 50164-5-2009 Lightning Protection Components (LPC) — Part 5 Requirements for earth electrode inspection housings and earth electrode seals.doc》由会员分享，可在线阅读，更多相关《（BS英国标准）BS EN 50164-5-2009 Lightning Protection Components (LPC) — Part 5 Requirements for earth electrode inspection housings and earth electrode seals.doc（15页珍藏版）》请在三一文库上搜索。
1、BS EN 50164-5:2009BSI British StandardsLightning ProtectionComponents (LPC) Part 5: Requirements for earth electrode inspection housings and earth electrode sealsNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWraising standards worldwideBS EN 50164-5:2009BRITISH STANDARDNationa
2、l forewordThis British Standard is the UK implementation of EN 50164-5:2009.The UK participation in its preparation was entrusted to Technical CommitteeGEL/81, Protection against lightning.A list of organizations represented on this committee can be obtained on request to its secretary.This publicat
3、ion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 63646 2ICS 91.120.40Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the aut
4、hority of the StandardsPolicy and Strategy Committee on 31 March 2009Amendments issued since publicationAmd. No. Date Text affectedBS EN 50164-5:2009EUROPEAN STANDARDEN 50164-5NORME EUROPENNEEUROPISCHE NORM January 2009 ICS 91.120.40English versionLightning Protection Components (LPC) -Part 5: Requi
5、rements for earth electrode inspection housings and earth electrode sealsComposants de protection contre la foudre (CPF) -Partie 5: Prescriptions pour les regards de visite et les joints dtanchitdes lectrodes de terreBitzschutzbauteile - Teil 5: Anforderungenan Revisionsksten undErderdurchfhrungenTh
6、is European Standard was approved by CENELEC on 2008-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical ref
7、erences concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC
8、member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icela
9、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.CENELECEuropean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisch
10、es Komitee fr Elektrotechnische NormungCentral Secretariat: avenue Marnix 17, B - 1000 Brussels 2009 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 50164-5:2009 EBS EN 50164-5:2009EN 50164-5:2009 5 ForewordThis European Standard wa
11、s prepared by the Technical Committee CENELEC TC 81X, Lightning protection.The text of the draft was submitted to the Unique Acceptance Procedure and was approved byCENELEC as EN 50164-5 on 2008-12-01. The following dates were fixed:national standard or by endorsement(dop)2009-12-01latest date by wh
12、ich the national standards conflicting with the EN have to be withdrawn(dow)2011-12-01latest date by which the EN has to be implemented at national level by publication of an identicalContents1Scope .42Normative references.43Definitions .44Requirements .44.1Documentation .44.2Earth electrode inspect
13、ion housing.54.3Earth electrode seal .55Marking.56Tests .56.1General .56.2Earth electrode inspection housing.66.3Earth electrode seal .76.4Marking test .86.5Acceptance criteria .87Electromagnetic compatibility (EMC).88Structure and content of the test report .88.1Report identification .88.2Sample de
14、scription .98.3Standards and references .98.4Test procedure .98.5Testing equipment, description .98.6Results and parameters recorded .9FiguresFigure 1Test arrangement.6Figure 2Test arrangement.71 ScopeThis European Standard specifies the requirements and tests for earth electrode inspection housings
15、 (earth pit), earth electrode seals.Lightning protection components (LPC) may also be suitable for use in hazardous atmospheres. Regard should then be taken of the extra requirements necessary for the components to be installed in such conditions.2 Normative referencesThe following referenced docume
16、nts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 62305-1, Protection against lightning Part 1: General principles (IEC 62305-1)
17、EN 62305-3, Protection against lightning Part 3: Physical damage to structures and life hazard(IEC 62305-3, mod.)EN 62305-4, Protection against lightning Part 4: Electrical and electronic systems within structures(IEC 62305-4)3 DefinitionsFor the purposes of this document, the following terms and de
18、finitions apply.3.1earth electrode inspection housingmetallic or non-metallic enclosure that houses the down conductor/earth termination connection for inspection and testing purposes. This consists of a housing and a removable lid3.2earth electrode sealwater pressure seal used in conjunction with a
19、n earth rod electrode that passes through the foundation of the building, so preventing ground water from entering the building4 RequirementsAll earth electrode inspection housings and earth electrode seals shall be so designed and constructed that in normal use their performance is reliable and wit
20、hout danger to persons and the surrounding.The choice of a material depends on its ability to match the particular application requirements.4.1 DocumentationThe manufacturer or supplier of the earth electrode inspection housing and earth electrode seals shall provide adequate information in his lite
21、rature to ensure that the installer can select and install the materials in a suitable and safe manner, in accordance with EN 62305-3.Compliance is checked by inspection.4.2 Earth electrode inspection housingThe design of the earth electrode inspection housing shall be such that it carries out its f
22、unction of enclosing the down conductor/earth rod termination in an acceptable and safe manner, and has sufficient internal dimensions to permit the assembly/disassembly of the earth rod clamp. The housing body shall be deep enough to permit the lid to sit flush on the body without fouling on the ro
23、d/conductor/clamp assembly.The material of the earth electrode inspection housing shall be compatible with the associated down conductor and earth rod termination and comply with the tests given in 6.2.The maximum total weight of the inspection housing shall be 25 kg.4.3 Earth electrode sealThe desi
24、gn of the earth electrode seal shall be such that it carries out its function of preventing ground water bi-passing the earth rod and entering the basement of a building, in an acceptable and safe manner.The material of the earth electrode seal shall be compatible with its surrounding environment an
25、d comply with the tests given in 6.3.5 MarkingAll products complying with this standard shall be marked at least with the following:a)manufacturers or responsible vendors name or trade mark;b)identifying symbol.Where this proves to be impractical the marking in accordance with b) may be given on the
26、 smallest packing unit.NOTE Marking may be applied for example by moulding, pressing, engraving, printing adhesive labels, or water slide transfers.Compliance is checked in accordance with 6.4.6 Tests6.1 GeneralThe tests in accordance with this standard are type tests.6.1.1 In normal use according t
27、o the manufacturers or suppliers instructions.6.1.2 All tests are carried out on new specimens.6.1.3 Unless otherwise specified, three specimens are subjected to the tests and the requirements are satisfied if all the tests are met. If only one of the specimens does not satisfy a test due to an asse
28、mbly or a manufacturing fault, that test and any preceding one which may have influenced the results of the test shall be repeated and also the tests which follow shall be carried out in the required sequence on another full set of specimens, all of which shall comply with the requirements.NOTE The
29、applicant, when submitting a set of specimens, may also submit an additional set of specimens which may be necessary should one specimen fail. The testing station will then, without further request, test the additional set of specimens and will reject only if a further failure occurs. If the additio
30、nal set of specimens is not submitted at the same time, the failure of one specimen will entail rejection.6.2 Earth electrode inspection housingAll tests shall be performed on three new lid samples using one housing.6.2.1Load testThe specimens shall be tested after a curing period. In the case of co
31、ncrete this shall be a minimum of28 days and 7 days for all other materials.The test is carried out on a complete assembly and prepared according to the manufacturers instructions.The housing of the specimen shall be cast in a concrete base following the manufacturer instructions. The arrangement sh
32、ould be placed on a rigid support.An example for an arrangement is shown in Figure 1.142 345556Legend1 Force4Housing2 Circular steel plate5Concrete base3 Removable lid6Rigid supportFigure 1 Test arrangementThe product applicable for heavy duty usage i.e. vehicular traffic areas shall be subjected to
33、 a force of40 kN vertically applied through a circular steel plate with a 170 mm 0,5 mm diameter and athickness of 20 mm 1 mm with an edge radius of approximately 2 mm.The product applicable for light duty usage i.e. walkways etc shall be subjected to a force of 15 kNvertically applied through a cir
34、cular steel plate with a 130 mm 0,5 mm diameter and a thickness of20 mm 1 mm with an edge radius of approximately 2 mm.The centre of the circular plate should be positioned over the centre of the lid.The force shall be gradually applied over 60 s 10 s and maintained for 120 s 5 s.BS EN 50164-5:2009E
35、N 50164-5:2009 7 6.2.2Acceptance criteriaDuring the test the lid shall show no deflection greater than 7 mm. After the test, the samples shall show no signs of disintegration, nor shall there be any cracks visible to normal or corrected vision without additional magnification. One minute after the l
36、oad has been removed, there shall be no permanent deformation exceeding 3 mm.The specimens are deemed to have passed the tests if all samples meet the above requirements.6.3 Earth electrode seal6.3.1Sealing testThe earth electrode seal shall be assembled in accordance with the manufacturers instruct
37、ions in a typical test bed that proves its intended application (as shown in Figure 2).5 bar214534Legend1 Tank2 Earth electrode3 Earth electrode seal arrangement4 Seals5 AirFigure 2 Test arrangementA minimum air pressure of 5 bar shall be applied for 24 h continuous to one end of the seal arrangement.6.3.2Acceptance c