《BS EN 1010-2-2006 Safety of machinery — Safety requirements for the design and construction of printing and paper converting machines.pdf》由会员分享，可在线阅读，更多相关《BS EN 1010-2-2006 Safety of machinery — Safety requirements for the design and construction of printing and paper converting machines.pdf（60页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1010-2:2006 Safety of machinery Safety requirements for the design and construction of printing and paper converting machines Part 2: Printing and varnishing machines including pre-press machinery The European Standard EN 1010-2:2006 has the status of a British Standard ICS 37
2、.100.10; 85.100 ? Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI BS EN 1010-2:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2006 BSI 2006 ISBN
3、0 580 48417 3 National foreword This British Standard is the official English language version of EN 1010-2:2006. The UK participation in its preparation was entrusted by Technical Committee MCE/3, Safeguarding of machinery, to Subcommittee MCE/3/9, Paper and printing machines Safety, which has the
4、responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section enti
5、tled “ International Standards Correspondence Index” , or by using the “ Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compli
6、ance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related inte
7、rnational and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 56, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document w
8、as last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1010-2 March 2006 ICS 37.100.10; 85.100 E
9、nglish Version Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 2: Printing and varnishing machines including pre-press machinery Scurit des machines - Prescriptions de scurit pour la conception et la construction de machines
10、dimpression et de transformation du papier - Partie 2: Machines dimpression et de vernissage ycompris les quipementsde pr-press Sicherheit von Maschinen - Sicherheitsanforderungen an Konstruktion und Bau von Druck- und Papierverarbeitungsmaschinen - Teil 2: Druck- und Lackiermaschinen einschlielich
11、Maschinen der Druckvorstufe This European Standard was approved by CEN on 17 January 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date l
12、ists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the res
13、ponsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ire
14、land, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassar
15、t, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1010-2:2006: E Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI EN 1010-2:
16、2006 (E) 2 ContentsPage Foreword 3 1Scope.5 2Normative references .6 3Terms and definitions.7 4List of significant hazards10 5Safety requirements and/or measures 15 5.1General 15 5.2Pre-press machinery.15 5.3Sheet-fed printing presses and varnishing machines (except screen printing presses)17 5.4Web
17、-fed rotary printing presses and varnishing machines.29 5.4.1General 29 5.5Screen printing presses .35 5.6Auxiliary devices for printing and varnishing machines .39 5.6.1General 39 5.6.2Cylinder and roller washing devices.39 5.6.3Continuous-flow drying devices40 5.6.4Powder spraying devices.41 5.6.5
18、Auxiliary devices on inking and damping units .41 5.6.6Plate clamping devices.42 5.6.7Washing equipment for printing forms, rollers and doctor blades.42 5.6.8Pile turners43 5.6.9Measuring and control devices44 6Verification of safety requirements and/or measures45 7Information for use .49 7.1Instruc
19、tion handbook .49 7.1.1Pre-press machinery.49 7.1.2Sheet-fed printing presses and varnishing machines .49 7.1.3Web-fed rotary printing presses and varnishing machines.50 7.1.4Screen printing presses .50 7.1.5Automatic cylinder and roller washing device .50 7.1.6Continuous-flow drying devices51 7.1.7
20、Alcohol-dosing devices51 7.1.8Washing equipment for printing forms, rollers and doctor blades.51 7.1.9Pile turners51 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC52 Annex ZB (informative) Relationship between this European
21、Standard and the Essential Requirements of EU Directive 94/9/EC.53 Bibliography.56 Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI ? EN 1010-2:2006 (E) 3 Foreword This document (EN 1010-2:2006) has been prepared by T
22、echnical Committee CEN/TC 198 “ Printing and paper machinery - Safety” , the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2006, and conflicting na
23、tional standards shall be withdrawn at the latest by September 2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directives. For relationship with EU Directives, see informa
24、tive Annexes ZA and ZB, which are integral parts of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fr
25、ance, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20
26、16:46:01 BST 2006, Uncontrolled Copy, (c) BSI ? EN 1010-2:2006 (E) 4 Introduction This document is a type C standard as stated in EN ISO 12100-1:2003. It defines additional safety requirements and/or deviations from the stipulations in EN 1010-1:2004. The machinery concerned and the extent to which
27、hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standa
28、rds for machines that have been designed and built according to the provisions of this type C standard. The European Committee for Standardization (CEN) draws attention to the fact that it is claimed that compliance with this document may involve the use of one or more patents: -German Patent DE 103
29、 10 236 B3 -PCT patent application CEN takes no position concerning the evidence, validity and scope of this patent right. The holders of this patent right have assured CEN that they are willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throug
30、hout the world. In this respect, the statement of the holders of this patent right is registered with CEN: The companies Koenig equipment for developing films and printing forms; washing machines for printing forms; machines for bending printing forms; punching machines for film and printing forms;
31、cutting machines for film and printing forms; machines for the production of gravure printing forms; scanners. Printing and varnishing machines: proofing presses; sheet-fed printing presses and varnishing machines including digital printing presses; web-fed rotary presses and varnishing machines inc
32、luding digital printing presses; screen printing presses. Auxiliary devices: cylinder and roller washing devices; continuous flow drying devices; powder spraying devices; auxiliary devices on inking and damping units; automatic plate clamping devices; washing equipment for printing forms, rollers an
33、d scrapers; pile turners; measuring and control devices. This document shall be used together with EN 1010-1:2004. Both parts together identify all significant hazards relevant to printing and varnishing machines including pre-press machinery and auxiliary devices, when they are used as intended and
34、 under the conditions foreseen by the manufacturer (see clause 4). The specific requirements specified in prEN 1010-2 take precedence over respective requirements in this standard. This document does not deal with risks generated by noise emitted from the machines. These issues are fundamentally cov
35、ered in EN 1010-1: 2004 Licensed Copy: London South Bank University, London South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI ? EN 1010-2:2006 (E) 6 This document does not apply to high-pressure cleaning devices and screen printing presses for textile substrates. This d
36、ocument is not applicable to printing and varnishing machines including pre-press machinery which are manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer
37、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs. EN 349:1993, Safety of machinery Minimum gaps t
38、o avoid crushing of parts of the human body. EN 378-1:2000, Refrigerating systems and heat pumps Safety and environmental requirements Part 1: Basic requirements, definitions, classification and selection criteria. EN 954-1:1996, Safety of machinery Safety related parts of control systems Part 1: Ge
39、neral principles for design. EN 999:1998, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts for the human body. EN 1010-1:2004, Safety of machinery Safety requirements for the design and construction of printing and paper converting machines Part 1: G
40、eneral requirements. EN 1050 :1996, Safety of machinery Principles for risk assessment. EN 1127-1:1997, Explosive atmospheres Explosion prevention and protection Part 1: Basic concepts and methodology. EN 1539 :2000, Dryers and ovens, in which flammable substances are released Safety requirements. E
41、N 60204-1:1997, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:1997). EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989). EN 60825-1:1994, Safety of laser products Part 1: Equipment classification, requirements and u
42、sers guide (IEC 60825-1:1993). EN 60950-1:2001, Information technology equipment Safety Part 1: General requirements (IEC 60950-1:2001, modified). EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design - Part 1: Basic terminology, methodology (ISO 12100-1:2003). EN IS
43、O 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003). EN ISO 14122-4:2004, Safety of machinery Permanent means of access to machinery Part 4: Fixed ladders (ISO 1422-4:2004) Licensed Copy: London South Bank University, Lond
44、on South Bank University, Sun Aug 20 16:46:01 BST 2006, Uncontrolled Copy, (c) BSI ? EN 1010-2:2006 (E) 7 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN ISO 12100-1:2003, EN 1010-1:2004 and the following apply. 3.1 alcohol dosing equipment e
45、quipment for dosing the amount of alcohol in the damping water of offset printing presses 3.2 proofing presses machines for printing a small number of copies, mostly used for assessing print quality before the printing form is mounted in the machine. Feeding and delivery is done manually 3.3 automat
46、ic plate clamping devices devices for automatic or semi-automatic changing of printing plates 3.4 exposing equipment machinery used for taking images by exposing photo-sensitive material, for example, as master copy or printing forms 3.5 sheet-fed printing presses and varnishing machines machines fo
47、r printing, numbering and/or varnishing of sheet-size substrates (paper sheets, board, film, sheet metal or similar material) including proofing presses. Numbering and varnishing machines may be integrated into printing presses or they may be used as stand-alone machines. The sheets may be fed by fe
48、eders or from sheeters attached to unwinding units 3.6 powder spraying devices devices for spraying powder onto the printed material on the delivery side of sheet-fed printing presses 3.7 printing forms base material which stores the image to be printed (pictures and/or text) and transfers ink on a
49、substrate (such as printing plates, printing cylinders, screens), thus printing the image 3.8 washing equipment for printing forms machines for washing printing forms outside the printing press (for example, screen washing equipment) 3.9 printing forms bending machines machines for bending or folding printing forms before they are clamped in the pri