《BS EN 1279-5-2005 Glass in building. Insulating glass units. Evaluation of conformity.pdf》由会员分享，可在线阅读，更多相关《BS EN 1279-5-2005 Glass in building. Insulating glass units. Evaluation of conformity.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1279-5:2005 Glass in building Insulating glass units Part 5: Evaluation of conformity The European Standard EN 1279-5:2005 has the status of a British Standard ICS 81.040.20 ? BS EN 1279-5:2005 This British Standard was published under the authority of the Standards Policy and
2、 Strategy Committee on 13 January 2006 BSI 13 January 2006 ISBN 0 580 46116 5 National foreword This British Standard is the official English language version of ? EN 1279-5:2005. The UK participation in its preparation was entrusted by Technical Committee B/520, Glass and glazing in building, to Su
3、bcommittee B/520/2, Glass and glazing in building Insulated glass products, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep ? UK interests informe
4、d; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in
5、 this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a
6、 contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 31 and a back cover. The BSI copyri
7、ght notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1279-5 May 2005 ICS 81.040.20 English version Glass in building - Insulating glass units - Part 5: Evaluat
8、ion of conformity Verre dans la construction - Vitrage isolant prfabriqu scell - Partie 5: Evaluation de la conformit Glas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5: Konformittsbewertung This European Standard was approved by CEN on 24 March 2005. CEN members are bound to comply with the CEN/C
9、ENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to an
10、y CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. C
11、EN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
12、and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 127
13、9-5:2005: E EN 1279-5:2005 (E) 2 Contents Page Foreword 3 1Scope.4 2Normative references .4 3Terms and definitions.5 4Requirements6 4.1Product description6 4.2Conformity with the definition of insulating glass units6 4.3Determination of the characteristics performances6 4.4Durability .10 4.5Dangerou
14、s substances.10 5Evaluation of conformity10 5.1General 10 5.2Initial type testing of the product (see 5.1, b)11 5.3Factory production control and inspection of samples in accordance with a prescribed test plan (5.1, 1) and 2)13 5.4Initial inspection of factory and of factory production control (5.1,
15、 a), 2).14 5.5Continuous surveillance and assessment of the factory production control (5.1, e).15 6Marking and/or labelling.16 6.1General 16 6.2Product marking .16 6.3Product characteristics 16 6.4“Characteristics/performance identification paper” 16 Annex A (informative) Use of IGUs when subjected
16、 to UV and/or in SSG .17 Annex B (informative) Installation of the insulating glass units.18 Annex C (informative) Provisions for voluntary involvement of third party(ies).21 Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive .22
17、Bibliography.31 ? EN 1279-5:2005 (E) 3 Foreword This European Standard (EN 1279-5:2005) has been prepared by Technical Committee CEN/TC 129 “Glass in building“, the secretariat of which is held by IBN/BIN. This European Standard shall be given the status of a national standard, either by publication
18、 of an identical text or by endorsement, at the latest by November 2005, and conflicting national standards shall be withdrawn at the latest by November 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports
19、 essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. No existing European Standard is superseded. This Part of the European Standard does not stand-alone, it is part of one standard with the general t
20、itle Glass in building - Insulating glass units: Part 1: Generalities, dimensional tolerances and rules for the system description Part 2: Long term test method and requirements for moisture penetration Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tol
21、erances Part 4: Methods of test for the physical attributes of edge seals Part 5: Evaluation of conformity Part 6: Factory production control and periodic tests This European Standard contains other aspects of importance of trade. This European Standard includes a Bibliography. According to the CEN/
22、CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
23、Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. ? EN 1279-5:2005 (E) 4 1 Scope This European Standard specifies requirements, the evaluation of conformity and the factory production control of insulating glass units for use in building
24、s. NOTE 1 For glass products with electrical wiring or connections for e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply. The main intended uses of the insulating glass units are installations in windows, doors, curtain walling, roofs and partitions where there
25、exists protection against direct ultraviolet radiation at the edges. NOTE 2 In cases where there is no protection against direct ultra-violet radiation at the edges, such as structural sealant glazing systems, additional European technical specifications should be followed (e.g. 00129113, prEN 13022
26、-1). NOTE 3 Units for which the intended use is only artistic and therefore no essential requirement is required, are not subject to CE marking and are not part of this European Standard. 2 Normative references The following referenced documents are indispensable for the application of this document
27、. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 356, Glass in building Security glazing Testing and classification of resistance against manual attack EN 410, Glass in building Determ
28、ination of luminous and solar characteristics of glazing EN 572-1, Glass in building Basic soda lime silicate glass products - Part 1: Definitions and general physical and mechanical properties EN 673, Glass in building Determination of thermal transmittance (U value) Calculation method EN 674, Glas
29、s in building Determination of thermal transmittance (U value) Guarded hot plate method EN 675, Glass in building Determination of thermal transmittance (U value) Heat flow meter method EN 1063, Glass in building Security glazing Testing and classification of resistance against bullet attack EN 1279
30、-1:2004, Glass in building Insulating glass units Part 1: Generalities, dimensional tolerances and rules for the system description EN 1279-2:2002, Glass in building Insulating glass units Part 2: Long term test method and requirements for moisture vapour penetration EN 1279-3:2002, Glass in buildin
31、g Insulating glass units Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances EN 1279-4:2002, Glass in building Insulating glass units Part 4: Methods of test for the physical attributes of edge seals EN 1279-6:2002, Glass in building Insulating gl
32、ass units Part 6: Factory production control and periodic tests EN 1748-1-1, Glass in building Special basic products Borosilicate glasses Part 1-1: Definition and general physical and mechanical properties EN 1748-2-1, Glass in building Special basic products Part 2-1: Glass ceramics Part 2-1: Defi
33、nition and general physical and mechanical properties ? EN 1279-5:2005 (E) 5 EN 1863-1, Glass in building Heat strengthened soda lime silicate glass Part 1: Definition and description EN 12150-1, Glass in building Thermally toughened soda lime silicate safety glass Part 1: Definition and description
34、 EN 12337-1, Glass in building Chemically strengthened soda lime silicate glass Part 1: Definition and description EN 12600, Glass in building Pendulum test Impact test method and classification for flat glass EN 12758, Glass in building Glazing and airborne sound insulation Product descriptions and
35、 determination of properties EN 12898, Glass in building Determination of the emissivity prEN 13022-1, Glass in building Structural sealant glazing Part 1: Glass products for structural sealant glazing systems Supported and unsupported monolithic and multiple glazing EN 13024-1, Glass in building Th
36、ermally toughened borosilicate safety glass Part 1: Definition and description EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN 13501-2, Fire classification of construction products and building eleme
37、nts Part 2: Classification using test data from fire resistance tests, excluding ventilation services prEN 13501-5, Fire classification of construction products and building elements Part 5: Classification using data from external fire exposure to roof tests EN 13541, Glass in building Security glaz
38、ing Testing and classification of resistance against explosion pressure EN 14178-1, Glass in building Basic alkaline earth silicate glass products Part 1: Float glass EN ISO 12543-1, Glass in building Laminated and laminated safety glass - Part 1: Definition and description of component parts (ISO 1
39、2543-1:1998) 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 1279-1:2004, EN 1279-2:2002, EN 1279-3:2002, EN 1279-4:2002 and EN 1279-6:2002 and the following apply. 3.1 initial type testing determination of the performance of a product (chara
40、cteristic, durability), on the basis of either actual tests or other procedures (such as conventional, standardised, tabulated or general accepted values, standardised or recognised calculation methods, test reports when made available,), in accordance with this European Standard that demonstrates c
41、ompliance with this European Standard 3.2 test report document that covers the results of tests undertaken on a representative sample of the product from production or on a prototype design of the product 3.3 product description document that details the relevant parameters, e.g. process conditions,
42、 structure, etc, for defining a product that complies with the standard. It includes specific references to characteristics that are modified by the production process ? EN 1279-5:2005 (E) 6 3.4 significant change variation in performance beyond the permitted tolerance for the characteristic 4 Requi
43、rements 4.1 Product description For conformity purposes the insulating glass unit manufacturer is responsible for the preparation and maintenance of the product description. This description shall describe the product and/or product families. Disclosure of the product description shall be at the dis
44、cretion of the insulating glass unit manufacturer or his agent except in the case of regulatory requirements. The description shall contain at least a normative part. The description may also contain an informative part, when the manufacturer foresees further development of the product. The normativ
45、e part of the description shall contain the following minimum information: a reference to EN 1279 Part 1, 2, 3, 4 and 6 and all other standards with which the manufacturer claims compliance; system description. The definition of product families shall be consistent with the normative part of the pro
46、duct description. The substitution of materials shall maintain the conformity with the product description. The substituting material can be added to the product family and also the product description when compliance has been demonstrated. 4.2 Conformity with the definition of insulating glass unit
47、s Products shall conform to the definition and fulfil the requirements of insulating glass units as defined in EN 1279-1. 4.3 Determination of the characteristics performances 4.3.1 Characteristics of glass panes for use in insulating glass units For panes made of glass covered by European specifica
48、tions generally accepted values, declared values, or calculated values of the characteristics listed in Table 1 shall be used. For panes made of glass not covered by European specifications measured values of the characteristics listed in Table 1 shall be used, and their chemical and mechanical stab
49、ility over time shall be demonstrated (refer to 5.2.4). ? EN 1279-5:2005 (E) 7 Table 1 - Necessary information on characteristics of glass panes for use in insulating glass units CharacteristicSymbolUnit - density - hardness - Youngs modulus - Poissons ratio - characteristic bending strength - specific heat capacity