《BS EN 1846-3-2008 Firefighting and rescue service vehicles — Part 3 Permanently installed equipment — Safety and performance1.pdf》由会员分享，可在线阅读，更多相关《BS EN 1846-3-2008 Firefighting and rescue service vehicles — Part 3 Permanently installed equipment — Safety and performance1.pdf（40页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1846-3:2002 Firefighting and rescue service vehicles Part 3: Permanently installed equipment Safety and performance ICS 13.220.10 ? +A1:2008 National foreword This British Standard is the UK implementation of EN 1846-3:2002+ A1:2008. It supersedes BS EN 1846-3:2002 which is wi
2、thdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The UK participation in its preparation was entruste
3、d by Technical Committee FSH/17, Fire brigade equipment, to Subcommittee FSH/17/3, Fire appliances. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are
4、 responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. BS EN 1846-3:2002+A1:2008 Amendments/corrigenda issued since publication Date Comments 30 June 2009Implementation of CEN amendment A1:2008 This British Standard was published u
5、nder the authority of the Standards Policy and Strategy Committee on 11 February 2004 BSI 2009 ISBN 978 0 580 62036 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1846-3:2002+A1 September 2008 ICS 13.220.10 Supersedes EN 1846-3:2002 English Version Firefighting and rescue service vehicles -
6、Part 3: Permanently installed equipment - Safety and performance Vhicules des services de secours et de lutte contre lincendie - Partie 3: Equipements installs demeure - Scurit et performances Feuerwehrfahrzeuge - Teil 3: Fest eingebaute Ausrstung - Sicherheits- und Leistungsanforderungen This Europ
7、ean Standard was approved by CEN on 9 September 2002 and includes Amendment 1 approved on 30 July 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
8、 Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translatio
9、n under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Gr
10、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manage
11、ment Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1846-3:2002+A1:2008: E EN 1846-3:2002+A1:2008 (E) 2 Contents page Foreword4 Introduction.5 1 Scope 6 2 Normative references7 3 Te
12、rms and definitions .8 4 List of significant hazards 10 4.1 Water installation.10 4.2 Additive installation.12 4.3 Monitor14 4.4 Equipment gantries .15 5 Requirements.16 5.1 General16 5.2 Safety requirements and/or protective measures16 5.2.1 General16 5.2.2 Water installation.16 5.2.3 Additive inst
13、allation.18 5.2.4 Monitor18 5.2.5 Equipment gantries .19 5.3 Performance requirements.19 5.3.1 General19 5.3.2 Water installation.19 5.3.3 Additive installation.23 5.3.4 Monitor25 5.3.5 Equipment gantries .25 6 Verification .26 6.1 General26 6.2 Verification of the safety requirements and/or measure
14、s.26 6.2.1 General26 6.2.2 Water installation.26 6.2.3 Additive installation.27 6.2.4 Monitor28 6.2.5 Equipment gantries .28 6.3 Verification of the performance requirements28 6.3.1 General28 6.3.2 Water installation.29 6.3.3 Additive installation.30 6.3.4 Monitor31 6.3.5 Equipment gantries .31 7 In
15、formation for use32 7.1 General32 7.2 Essential information and marking relevant to safety.32 7.3 Information and marking relevant to performance 32 Annex A (informative) Monitor throw measurement34 BS EN 1846-3:2002+A1:2008 w w w . b z f x w . c o m EN 1846-3:2002+A1:2008 (E) 3 Annex ZA (informativ
16、e) !Relationship between this European Standard and the Essential Requirements of EU Directive 98/37EC“35 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“.36 Bibliography37 BS EN 1846-3:2002+A1:2008 w w w . b z f x w . c o
17、 m EN 1846-3:2002+A1:2008 (E) 4 Foreword This document (EN 1846-3:2002+A1:2008) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an
18、identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This document includes Amendment 1, approved by CEN on 2008-07-30. This document supersedes EN 1846-3:2002. The start and finish of text introduced or
19、altered by amendment is indicated in the text by tags ! “. The CEN/TC 192 entrusted the drafting of this standard to CEN/TC 192/WG3 “Firefighting and rescue service vehicles“. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Associat
20、ion, and supports essential requirements of !EU Directive(s)“. !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ EN 1846 “Firefighting and rescue service vehicles“ is composed of three parts: Part 1: Nomenclature and designation; P
21、art 2: Common requirements - Safety and performance; Part 3: Permanently installed equipment - Safety and performance. Annex A is for information only. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europ
22、ean Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United King
23、dom. BS EN 1846-3:2002+A1:2008 w w w . b z f x w . c o m EN 1846-3:2002+A1:2008 (E) 5 Introduction This document is a type C standard as stated in !EN ISO 12100-1:2003“. This document is a complement to EN 1846-2 and deals with some optional specific permanently installed equipment used by firefight
24、ers. The equipment concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. NOTE Other equipment not covered by this document can be dealt with later in another part, depending on the decision of CEN. When provisions of this
25、type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. This document als
26、o deals with the performance requirements which apply to the equipment as defined in the scope. BS EN 1846-3:2002+A1:2008 w w w . b z f x w . c o m EN 1846-3:2002+A1:2008 (E) 6 1 Scope 1.1 This Part of this European Standard specifies the minimum requirements for safety and performance of some optio
27、nal specific permanently installed equipment on firefighting and rescue service vehicles, operated by trained persons, as designated in EN 1846-1 and specified in EN 1846-2. NOTE 1 Categories and mass classes of the firefighting and rescue service vehicles are given in EN 1846-1. The permanently ins
28、talled equipment dealt with in this Part of this European Standard is given below: water installation; additive installation; monitor; equipment gantries. NOTE 2 This Part of this European Standard should be read in conjunction with any national regulations in force for vehicles using the public roa
29、ds and with any EU Directives and associated EFTA regulations in force relevant to vehicles and their equipment. For the purposes of this European Standard, the normal ambient temperature range is - 15 C to + 35 C. NOTE 3 In the case of utilization outside this temperature range, the particular temp
30、erature range should be specified by the user. 1.2 This Part of this European Standard is not applicable to: personnel carrying vehicles; vehicles with a gross laden mass not exceeding 2 t; boats; aircrafts; trains; ambulances; airport vehicles complying with International Civil Aviation Organisatio
31、n (ICAO) recommendations. 1.3 This Part of this European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the commissioning, the operational use and the routine checking of firefighting and rescue service vehicles when carried out in ac
32、cordance with the specifications given by the manufacturer or his authorized representative. It deals also with performance requirements. It does not cover the hazards generated by: noise ( as permanently installed equipment cannot be operated separately from the vehicle, this hazard is covered in P
33、art 2); radiation (low frequency, radio frequency, radiation, microwaves); errors in the software; BS EN 1846-3:2002+A1:2008 w w w . b z f x w . c o m EN 1846-3:2002+A1:2008 (E) 7 use in potentially explosive atmospheres; construction, transportation, maintenance and decommissioning; wind pressure i
34、n and out of use; static electricity problems; remote control; electromagnetic compatibility; oil hydraulic and pneumatic driving system. 1.4 This document is not applicable to the equipment which is manufactured before its date of publication by CEN. 2 Normative references This European Standard in
35、corporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this
36、European Standard only when incorporated in it by amendment of revision. For undated references the latest edition of the publication referred to applies (including amendments). !deleted text“ EN 418, Safety of machinery Emergency stop equipment, functional aspects - Principles for design EN 953, Sa
37、fety of machinery Guards General requirements for the design and construction of fixed and movable guards EN 1050:1996, Safety of machinery Principles for risk assessment !deleted text“ EN 1028-1:2002, Fire-fighting pumps Fire-fighting centrifugal pumps with primer Part 1: Classification, general an
38、d safety requirements EN 1028-2, Fire-fighting pumps Fire-fighting centrifugal pumps with primer Part 2: Verification of general and safety requirements EN 1846-1:1998, Firefighting and rescue service vehicles Part 1: Nomenclature and designation EN 1846-2:2001, Firefighting and rescue service vehic
39、les Part 2: Common requirements - Safety and performance EN 1846-2:2001/prA1, Firefighting and rescue service vehicles Part 2: Common requirements - Safety and performance prEN 1947, Fire-fighting hoses Semi-rigid delivery hoses and hose assemblies for pumps and vehicles !EN ISO 12100-1:2003, Safety
40、 of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003)“ BS EN 1846-3:2002+A1:2008 w w w . b z f x w .
41、c o m EN 1846-3:2002+A1:2008 (E) 8 3 Terms and definitions For the purposes of this Part of this European Standard, the terms and definitions given in !EN ISO 12100-1:2003“, EN 1846-1:1998, EN 1846-2:2001 together with the following apply. 3.1 water installation combination of components for the col
42、lection, storage and delivery of water and/or water-additive mixture at varying pressures and delivery rates 3.1.1 specified rate(s) of the water installation, Q1 specified rate(s) corresponding to the nearest lower value(s) in the following list : 250 l/min 500 l/min 750 l/min 1 000 l/min 1 500 l/m
43、in 2 000 l/min 3 000 l/min 4 000 l/min 6 000 l/min 3.1.2 specified outlet pressure(s) of the water installation, pa1 specified outlet pressure(s) corresponding to the nearest lower value(s) in the following list : 6 bar 10 bar 15 bar 40 bar 3.1.3 height difference of level between the standing surfa
44、ce of the vehicle and the water surface at the time of a pumping appliance suction operation 3.1.4 specified height of the water installation, d specified height where d equals 1,5 m or 3 m 3.1.5 standing surface of the vehicle surface on which the vehicle wheels are resting when it is operating 3.1
45、.6 standing surface of the operator surface on which the operator stands 3.1.7 installed water pump pump permanently installed on a vehicle and driven by the motive power of the vehicle, or a pump complete with drive motor 3.1.8 installed water tank container for storage of water for fire service pu
46、rposes 3.1.9 supply and delivery connections for water inlet and outlet devices for joining hoses to the pipework installation 3.1.10 pipework installation for water any system linking the installed water pump(s), the installed water tank(s) and the supply and delivery connections 3.1.11 operating a
47、nd control instruments for water controls and gauges necessary to operate and monitor the water installation system BS EN 1846-3:2002+A1:2008 EN 1846-3:2002+A1:2008 (E) 9 3.1.12 hosereel system rotating hose storage system with semi-rigid hose(s) permanently connected to the pipework installation 3.
48、1.13 wheeled hosereel hosereel designed for the storage, the transport and the deployment of layflat hose 3.2 liquid additive addition to water to enhance firefighting capabilities e.g. foam concentrate, fire retardant NOTE In this document, the term “additive“ means “liquid additive“. 3.2.1 additiv
49、e installation combination of components for the collection, storage and delivery of additive at varying pressures and delivery rates before mixing with water 3.2.2 installed additive pump pump permanently installed on a vehicle and driven by the motive power of the vehicle, or a pump complete with drive motor 3.2.3 installed additive tank container for storage of additive for fire service purposes