《BS EN 442-1-1996 散热器和热空气对流加热器规范.第1部分技术规范和要求.pdf》由会员分享，可在线阅读，更多相关《BS EN 442-1-1996 散热器和热空气对流加热器规范.第1部分技术规范和要求.pdf（18页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 442-1:1996 Incorporating Amendment No. 1 Specification for radiators and convectors Part 1: Technical specifications and requirements The European Standard EN 442-1:1995, with the incorporation of amendment 1:2003, has the status of a British Standard ICS 91.140.10 BS EN 442-1
2、:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1996 BSI 26 February 2004 The following BSI references relate to the work on this British Standard: Committ
3、ee reference RHE/6 Draft for comment 94/711410 DC ISBN 0 580 25776 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee RHE/6, Air or space heaters or coolers without combustion, upon which the following bodies were represen
4、ted: Aluminium Federation Association of British Health-Care Industries Boiler and Radiator Manufacturers Association Limited Building Services Research and Information Association Chartered Institution of Building Services Engineers Hevac Association Institute of Domestic Heating Engineers Institut
5、e of Refrigeration Manufacturers Association of Radiators and Convectors Limited National Association of Plumbing, Heating and Mechanical Services University of Portsmouth Coopted members Amendments issued since publication Amd. No.DateComments 1486126 February 2004Changes to EN foreword and see nat
6、ional foreword BS EN 442-1:1996 BSI 26 February 2004 i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 442-13 BS EN 442-1:1996 ii BSI 26 February 2004 National foreword This British Standard has been prepared by Technical Committee RHE/6 and is the Eng
7、lish language version of EN 442-1:1995, Radiators and convectors Part 1: Technical specifications and requirements, including amendment 1:2003, published by the European Committee for Standardization (CEN). The start and finish of text introduced or altered by amendment is indicated in the text by t
8、ags . Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by . EN 442-1 was produced as a result of international discussion in which the UK took and active part. BS EN 442-1 and BS EN 442-2 supersede BS 3528:1977 whic
9、h is withdrawn. It should be noted that in5.1.3 reference is made to alloy AlSi9Cu (N.46 000 and N.46 001) with a Footnote. These references related to a draft from CEN/TC 132, now available as prEN 1706 which has yet to be published and it is envisaged that the references in this standard will be r
10、evised by amendment after publication. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” faci
11、lity of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligation
12、s. 1) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 13 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. 1)The European Standard refers to ISO 31-4:1978 whi
13、ch has been superseded by ISO 31-4:1992. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 442-1 December 1995 +A1 September 2003 ICS 91.140.10 Descriptors: Space heaters, heat radiators, convectors, specifications, mechanical strength, calorific power, marking, labelling English version Radiator
14、s and convectors Part 1: Technical specifications and requirements (includes amendment A1:2003) Radiateurs et convecteurs Partie 1: Spcifications et exigences techniques (inclut lamendement A1:2003) Radiatoren und Konvektoren Teil 1: Technische Spezifikationen und Anforderungen (enthlt nderung A1:20
15、03) This European Standard was approved by CEN on 1995-05-04; amendment A1 was approved by CEN on 7 June 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte
16、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by trans
17、lation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,
18、Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights
19、 of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 442-1:1995 + A1:2003 E EN 442-1:1995 BSI 26 February 2004 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 130, Space heating appliances with
20、out integral heat sources, of which the Secretariat is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1996, and conflicting national standards shall be withdrawn at the latest b
21、y June 1996. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directives, see informative Annex ZA, which is an integral part of this docum
22、ent. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Ki
23、ngdom. Foreword to amendment A1 This document EN 442-1:1995/A1:2003 has been prepared by Technical Committee CEN/TC 130, Space heating appliances without integral heat sources, the Secretariat of which is held by UNI. This Amendment to the European Standard EN 442-1:1995 shall be given the status of
24、 a national standard, either by publication of an identical text or by endorsement, at the latest by March 2004, and conflicting national standards shall be withdrawn at the latest by March 2004. This document has been prepared under a mandate given to CEN by the European Commission and the European
25、 Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count
26、ries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. Contents Page 0Introductio
27、n3 1Scope3 2Normative references3 3Definitions, symbols and units of measurement3 4Pretreatment and paint4 5Dimensional tolerances and pressure tightness4 6Thermal output6 7Catalogue data6 8Marking and labelling7 Annex ZA (informative) Clauses of this European Standard addressing the provisions of t
28、he EU Construction Products Directive8 Bibliography13 EN 442-1:1995 BSI 26 February 2004 3 0 Introduction This European Standard of radiators and convectors consists of the following parts: Part 1:Technical specifications and requirements; Part 2: Testing and rating methods; Part 3: Evaluation of co
29、nformity. 1 Scope This European Standard defines the technical specifications and requirements of radiators and convectors to be installed in central heating systems in residential buildings. Radiators and convectors are components for installation in a permanent manner in construction works. This E
30、uropean Standard covers radiators and convectors fed with water or steam at temperatures below 120 C, supplied by a remote heat source. This European Standard does not apply to independent heating appliances. This European Standard also defines the additional common data that the manufacturer shall
31、provide to the trade in order to ensure the correct application of the products. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publicatio
32、ns are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 442-2:1996, Ra
33、diators and convectors Part 2: Testing and rating methods. EN 442-3:2003, Radiators and convectors Part 3: Evaluation of conformity. EN 573-3, Wrought aluminium and aluminium alloys Chemical composition and forms of products Part 3: Chemical composition. EN 10130, Cold rolled low carbon steel flat p
34、roducts for cold forming; Technical delivery conditions. EN 10131, Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming on dimensions shape. EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data f
35、rom reaction to fire tests. EN 45001, General criteria for the operation of testing laboratories. ISO 31-4:1978, Quantities and units Part 4: Heat. ISO 185:1988, Grey cast iron Classification. ISO 2409:1992, Paints and varnishes Cross-cut test. 3 Definitions, symbols and units of measurement See EN
36、442-2:1996. EN 442-1:1995 4 BSI 26 February 2004 4 Pretreatment and paint The pretreatment and paint processes used, shall provide a protective coating to all external surfaces in contact with the air which shall: give protection against corrosion in normal storage and installation conditions (as de
37、monstrated by absence of surface corrosion after 100 h humidity test according to a technical specification valid in the country of destination; be resistant to minor impact damage as demonstrated by a 2 mm cross-hatch test with a single blade cutting tool manually operated according to ISO 2409:199
38、2. The test result shall be within the first three steps (0-1-2) of Table 1 of ISO 2409:1992. The paint shall not contain any chemical substances the use of which is not allowed in building products2). The compliance with the relevant Directive shall be stated by the manufacturer of the radiator/con
39、vector. 5 Dimensional tolerances and pressure tightness The dimensional tolerances shall not be greater than those in the manufacturers drawings. In any case they shall not be greater than those given in Table 2 of EN 442-2:1996. 5.1 Material specification and wall thickness of wet heating surface T
40、he following values for material thickness for steel radiators, tubular radiators and finned tube convectors shall be measured before pressing or fabrication. Wall thickness of cast-iron, cast aluminium or extruded aluminium radiators refers to the nominal drawing dimensions minus all admissible tol
41、erances. 5.1.1 Steel radiators (radiators manufactured from steel sheet or coil) The wet heating surface materials of steel radiators shall be low carbon steel sheet, which is free from scale or rust and which complies with EN 10130 grade Fe PO1 and with EN 10131. The thickness of the steel used for
42、 wet surfaces shall not be less than 1,11 mm. The compliance with this requirement shall be verified by measuring. 5.1.2 Cast-iron radiators Cast-iron radiators shall be manufactured from grey cast-iron complying with ISO 185. The wet wall thickness shall not be less than 2,5 mm. The minimum wall th
43、ickness shall be ensured by periodic controls of the casting equipment and daily random production checks. Compliance with this requirement shall be verified by measurement. 5.1.3 Cast aluminium radiators Cast aluminium alloy radiators shall be manufactured from alloy AlSi9Cu3): (N. 46 000 and N. 46
44、 001). The wet wall thickness shall not be less than 1,5 mm. The minimum wall thickness shall be ensured by periodic controls of the casting equipment and daily random production checks. Compliance with this requirement shall be verified by measurement. 2) Also in relation to Directive 76/769/EEC, a
45、s amended. 3)prEN 1706 is under preparation by CEN/TC 132/WG1. See Table 1. EN 442-1:1995 BSI 26 February 2004 5 5.1.4 Extruded aluminium radiators Extruded aluminium alloy radiators shall be manufactured from wrought aluminium alloy EN AW-6060 of the EN 573-3 corresponding to the alloy AlMgSi. The
46、wet wall thickness shall not be less than 1,1 mm. The minimum wall thickness shall be ensured by periodic controls of the extruder and daily random production checks. Compliance with this requirement shall be verified by measurement. 5.1.5 Tubular radiators The material specification and gauge of tu
47、bes used in manufacture will be dependent on the tube size and profile and on the process of assembly. They shall nevertheless be sufficient to satisfy the general minimum requirements of 5.2 and 5.3 and the wall thickness of the tube used shall not be less than 0,8 mm. Compliance with this requirem
48、ent shall be verified by measurement. 5.1.6 Finned tube convectors The wall thickness of the tube shall not be less than 0,8 mm. Compliance with this requirement shall be verified by measurement. 5.1.7 Reaction to fire The materials from which radiators and convectors are made (steel, cast iron and
49、aluminium) are considered to be reaction to fire Class A1 without the need for testing4), provided that any organic part of the paint or coating is less than 1 % by mass or volume. If any organic part of the paint or coating exceeds 1 % by mass or volume (whichever is the more onerous), the material shall be tested and classified according to EN 13501-1 and the resulting class stated. The percentage of organic part of the paint or coating is referred to the actual operating conditions of the radiator and convector (i.e. to the ma