《BS EN 1177-2008 冲击减震游乐场铺面.临界跌落高度的测定.pdf》由会员分享，可在线阅读，更多相关《BS EN 1177-2008 冲击减震游乐场铺面.临界跌落高度的测定.pdf（20页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1177:2008 Impact attenuating playground u surfacing Determination of critical fall height ICS 97.200.40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BS EN 1177:2008 This British Standard was p
2、ublished under the authority of the Standards Policy and Strategy Committee e on 31 October 2008 BSI 2008 ISBN 978 0 580 55368 4 National foreword This British Standard is the UK implementation of EN 1177:2008. It supersedes BS EN 1177:1998, which will be withdrawn on 31 May 2009. The UK committee c
3、onsiders it essential that BS EN 1177 should be used in conjunction with BS 7188 so that other properties of abrasive wear, resistance to indentation and ease of ignition are still measured. The UK participation in its preparation was entrusted to Technical Committee SW/65, Childrens playground equi
4、pment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immun
5、ity from legal obligations. Amendments/corrigenda issued since publication DateComments nnnn n n n nn n nnn nn nnnn nnnnn n n nnn n nn n nn nnnnn n n n n n n nnn nn n n n n nnn nn n n nnn nnnn n n n n n nnn nn nn n nn nnn nnn n n nn n nnn nn nnnn n nnn nnnn n n n nn nn n n nn nnn n n nnn nn n nn n n
6、 n nn nn n nn nn n n n n nn n nn n n n nn n nn EN 1177:2008 (E) 2 Contents Page Foreword3 Introduction.5 1Scope 6 2Normative references6 3Terms and definitions .6 4Test method7 4.1Principle7 4.2Apparatus.7 4.3Accuracy of tests.8 4.4Conditions for testing .9 4.4.1Testing in the laboratory.9 4.4.2Test
7、ing on site10 4.5Procedure .10 4.5.1Time/acceleration trace.10 4.5.2Selection and definition of the test position.10 4.5.3Procedures for specific types of product .11 4.5.4Selection of data for determination of critical fall height12 4.6Calculation of results 12 4.7Test report13 4.7.1General13 4.7.2
8、Tests carried out in the laboratory 13 4.7.3Tests carried out on site.13 Annex A (informative) Test rig for determination of critical fall height.15 Annex B (informative) Typical examples of trace of acceleration against time and curve of HIC values against drop height.16 BS EN 1177:2008 EN 1177:200
9、8 (E) 3 Foreword This document (EN 1177:2008) has been prepared by Technical Committee CEN/TC 136 Sports, playground and other recreational facilities and equipment , the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publicati
10、on of an identical text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall n
11、ot be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia
12、, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. This document supersedes EN 1177:1997. European standards for playground
13、equipment and surfacing comprise this European Standard and EN 1176, which consists of a number of parts as follows: EN 1176-1, Playground equipment and surfacing Part 1: General safety requirements and test methods EN 1176-2, Playground equipment and surfacing Part 2: Additional specific safety req
14、uirements and test methods for swings EN 1176-3, Playground equipment and surfacing Part 3: Additional specific safety requirements and test methods for slides EN 1176-4, Playground equipment and surfacing Part 4: Additional specific safety requirements and test methods for cableways EN 1176-5, Play
15、ground equipment and surfacing Part 5: Additional specific safety requirements and test methods for carousels EN 1176-6, Playground equipment and surfacing Part 6: Additional specific safety requirements and test methods for rocking equipment EN 1176-7, Playground equipment and surfacing Part 7: Gui
16、dance on installation, inspection, maintenance and operation EN 1176-10, Playground equipment and surfacing Part 10: Additional specific safety requirements and test methods for fully enclosed play equipment EN 1176-11, Playground equipment and surfacing Part 11: Additional specific safety requireme
17、nts and test methods for spatial network For inflatable play equipment see EN 14960, Inflatable play equipment Safety requirements and test methods BS EN 1177:2008 EN 1177:2008 (E) 4 The principal changes from the previous edition of this European Standard are that all safety requirements have been
18、removed and are now included in EN 1176-1 so that this standard is now only a method for assessing impact attenuation. As a result of round robin testing, additional criteria for carrying out the test procedure and additional requirements for the test equipment have been introduced. BS EN 1177:2008
19、EN 1177:2008 (E) 5 Introduction This European Standard is based on the safety principles given in EN 1176-1 for playground equipment and provides a method for the assessment of impact attenuation of surfaces intended for use in the impact area as defined in EN 1176-1. Injuries caused by falls from p
20、layground equipment occur for a variety of reasons but the most severe injuries are likely to be injuries to the head. The committee responsible for this European Standard recognizes that there are many factors that influence injury mechanisms independent of the surfacing, e.g. body orientation, awk
21、wardness of fall, bone density, etc. Recent research has indicated that permanent disabilities and long bone injuries could be influenced by the duration of the acceleration pulse. The committee responsible for this European Standard intends to consider recent research in this area in a future revis
22、ion of this standard. Consequently, priority has been given to developing a criterion for surfacing materials intended to assess their ability to reduce the likelihood of head injuries. On the basis of statistical analysis of available data the Head Injury Criterion (HIC) at a tolerance level of 1 0
23、00 has been used as the upper limit for the brain injury severity unlikely to have disabling or fatal consequences. By choosing measurement of HIC as the criterion of safety, the method considers only the kinetic energy of the head when it impacts the surface of the impact area. This is considered t
24、o be the best model available to predict the likelihood of head injury from falls. Surfaces fulfilling the test requirements of this standard are considered to be in compliance with the requirements for impact attenuation in EN 1176-1. NOTE The HIC value of 1 000 is merely one data point on a risk s
25、everity curve where a HIC of 1 000 is equivalent to a 3 % chance of a critical injury (MAIS1) 5), a 18 % probability of a severe (MAIS 4) head injury, a 55 % probability of a serious (MAIS 3) head injury, a 89 % probability of a moderate injury (MAIS 2), and a 99,5 % chance of a minor head injury (M
26、AIS 1), to an average male adult. There are a variety of materials available providing impact attenuation, including rubber tiles, mats, slabs, continuous synthetic surfacing, either prefabricated or formed in-situ, loose particulate material, such as gravel, sand, wood chips, bark, etc. The method
27、in this European Standard can be used to assess any of these surfaces. 1) Maximum Abbreviated Injury Scale, first developed by the Association for the Advancement of Automotive Medicine and used extensively in the automotive industry as an indicator of the severity of head-related injuries. BS EN 11
28、77:2008 EN 1177:2008 (E) 6 1 Scope This European Standard specifies a method for determining the impact attenuation of playground surfacing. It defines a Critical Fall Height“ (see 3.2) for surfacing, which represents the upper limit of its effectiveness in reducing head injury when using playground
29、 equipment conforming to EN 1176. The test methods described in the European Standard are applicable for tests carried out in a laboratory and for tests on site. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, on
30、ly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method EN 1176-1:2008, Playground equipment and
31、 surfacing Part 1: General safety requirements and test methods EN ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005) ISO 6487:2002, Road vehicles Measurement techniques in impact tests Instrumentation 3 Terms and definitions For the p
32、urposes of this document, the terms and definitions given in EN 1176-1:2008 and the following apply. 3.1 impact attenuation property of a surface, which dissipates the kinetic energy of an impact by localized deformation or displacement such that the acceleration is reduced 3.2 critical fall height
33、maximum free height of fall, for which a surface will provide an acceptable level of impact attenuation, determined as described in 4.4 3.3 head injury criterion (HIC) value criterion for head injuries caused from falls as calculated in accordance with 4.6.1 3.4 test position position on the materia
34、l to be tested located vertically below the centre of the headform 3.5 drop height distance between the test position on the surfacing and the lowest point of the free falling headform prior to release NOTE In the case of a guided headform this value is calculated from measurement of velocity at imp
35、act (see 4.2.6). 3.6 impact measurement HIC value from the recorded acceleration of the headform falling from one fall height onto one test position BS EN 1177:2008 EN 1177:2008 (E) 7 3.7 drop test series of impact measurements determined from at least four increasing drop heights 3.8 loose particul
36、ate material material which absorbs the energy of an impact usually through its displacement 4 Test method 4.1 Principle Test specimens or installed areas of the impact attenuating material under test are struck by an instrumented headform in a defined series of impacts from different drop heights.
37、The signal emitted by an accelerometer (see Figure B.1) in the headform during each impact is processed to yield a severity from the measured impact energy, defined as head injury criterion (HIC). The HIC of each impact is plotted and the critical fall height is determined as the lowest drop height
38、producing a HIC value of 1 000 (see Figure B.2). 4.2 Apparatus 4.2.1 Test rig, comprising a headform with accelerometer (4.2.2), optionally with a charge amplifier (4.2.3) and, if using a uniaxial accelerometer, a guidance system (4.2.4) and impact measuring equipment (4.2.8), as shown in Figure A.1
39、. 4.2.2 Headform, consisting of either a) an aluminium alloy ball; or b) a hemispherical ended aluminium alloy missile. It shall have a diameter of 160 mm 5 mm, a mass of 4,6 kg 0,05 kg, with a maximum deviation from the hemispheric surface of 0,5 mm, incorporating an accelerometer as follows: c) tr
40、iaxial accelerometer for free falling headforms, mounted in the centre of gravity of the headform; or d) uniaxial accelerometer for guided headforms, aligned to measure in the vertical axis 5 and located directly above the centre of mass. The impacting part of the headform between the lower boundary and accelerometer shall be homogeneous and free from voids. 4.2.3 Charge amplifier (optional) 4.2.4 Guidance system,