《BS EN 3660-017-2009 Aerospace series — Cable outlet accessories for circular and rectangular.pdf》由会员分享，可在线阅读，更多相关《BS EN 3660-017-2009 Aerospace series — Cable outlet accessories for circular and rectangular.pdf（14页珍藏版）》请在三一文库上搜索。
1、? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? BS EN 3660-017:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3660-017 March 2009 ICS 49.060 English Version Aerospace series - Cable outlet accessories for circular and rectangular electrical and optical connectors -
2、 Part 017: Cable outlet, style A, straight, unsealed, with cable tie strain relief - Product standard Srie arospatiale - Accessoires arrire pour connecteurs circulaires et rectangulaires lectriques et optiques - Partie 017: Raccord droit non tanche, type A, avec tenue du cble par frettage - Norme de
3、 produit Luft- und Raumfahrt - Endgehuse fr elektrische und optische Rund- und Rechtecksteckverbinder - Teil 017: Endgehuse, Bauform A, gerade, nicht abgedichtet, mit Arm fr Kabelbinder - Produktnorm This European Standard was approved by CEN on 30 August 2008. CEN members are bound to comply with t
4、he CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centr
5、e or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official
6、 versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloven
7、ia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN nati
8、onal Members. Ref. No. EN 3660-017:2009: E BS EN 3660-017:2009 EN 3660-017:2009 (E) 2 Contents Page Foreword 3 1Scope 4 2Normative references 4 3Terms and definitions .4 4Characteristics .4 5Designation 9 6Marking 10 7Technical specification 10 ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 3 Foreword T
9、his document (EN 3660-017:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations a
10、nd the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2009, and conflicting national standards shall
11、be withdrawn at the latest by September 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Re
12、gulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Ne
13、therlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 4 1 Scope This product standard defines a range of cable outlets, style A, straight, unsealed, with cable tie strain relief. Associated elec
14、trical connector(s) : see EN 3660-002. Temperature range, Class A : 65 C to 200 C Class N : 65 C to 200 C Class W : 65 C to 175 C 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. Fo
15、r undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 2591-100*, Aerospace series ? Elements of electrical and optical connection ? Test methods ? Part 100: General. EN 3660-001, Aerospace s
16、eries Cable outlet accessories for circular and rectangular electrical and optical connectors Part 001: Technical specification. EN 3660-002, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 002: Index of product standards. EN 3660-036, Ae
17、rospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 036: Spacer spad Product standard.1) AS85049A, Connector accessories, electrical general specification for.2) 3 Terms and definitions For the purposes of this document, the terms and definitio
18、ns given in EN 3660-001 apply. 4 Characteristics 4.1 Dimensions and masses For dimensions and masses, see Figure 1, Figure 2c) and Table 1. Dimensions and tolerances are in millimetres. * All its parts quoted in this standard. 1) In preparation at the date of publication of this standard. 2) Publish
19、ed by: Department of Defense (DOD), the Pentagon, Washington, DC 20301, USA ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 5 Key 1 Cable tie or lacing cord Figure 1 Detail A: see Figures 2a) to 2e). Figure 2a) Without lug and spacer pad Figure 2b) Without lug and with spacer pad Figure 2c) With lug and
20、without spacer pad Figure 2d) With lug and spacer pad Figure 2e) Spacer pad see EN 3660-036 Table 1 Shell size A B C a DEFGNumber of teeth WithoutWith ThreadWithoutWithWithoutWithRadius self-locking self-locking lug Masses max. Classes A, N and W max. 0,38max. max. min. g 09 M12x1-6H 19,60 24,80 6,2
21、9 27,10 29,10 12,50 7,59 1,90 12 5,5 6,5 11 M15x1-6H 20,80 26,90 6,29 27,10 29,10 12,50 10,85 2,50 16 6,0 7,5 13 M18x1-6H 23,90 29,70 6,29 27,10 29,10 12,50 13,74 3,40 20 7,5 9,0 15 M22x1-6H 27,20 32,70 6,29 30,20 32,20 12,50 16,92 4,20 24 11,0 13,0 17 M25x1-6H 30,70 36,10 6,29 31,10 33,10 12,50 20,
22、09 5,00 28 12,5 14,5 19 M28x1-6H 34,50 39,10 6,29 31,10 33,10 12,50 22,18 5,50 32 13,5 16,0 21 M31x1-6H 37,60 42,40 6,29 31,10 33,10 12,50 25,96 6,20 36 15,0 18,5 23 M34x1-6H 40,60 51,10 6,29 31,10 33,10 12,50 29,13 7,20 40 17,5 20,5 25 M37x1-6H 43,20 53,80 6,29 31,10 33,10 12,50 32,31 7,90 44 20,5
23、25,0 a “C” dimensions is taken when the coupling nut is pulled in forward position. A CD B E G F A 5,8 Ref. 1 6,6 8,4 3,6 D 3,3 ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 6 4.2 Interface dimensions 4.2.1 Associated connectors See EN 3660-002. 4.2.2 Standard AS85049 interface See Figure 3 and Table 2
24、. All dimensions in millimetres. Figure 3 Table 2 Shell size A B CDN Number of teeth 0 0,15 min. min. min. mm mm mm mm 09 10,57 7,50 6,70 2,90 12 11 13,56 10,80 9,90 2,90 16 13 16,58 13,80 12,80 2,90 20 15 20,57 16,90 16,00 2,90 24 17 23,57 20,10 19,20 2,90 28 19 25,57 22,80 21,40 2,90 32 21 29,97 2
25、6,00 24,60 2,90 36 23 32,56 29,10 27,70 2,90 40 25 35,56 32,30 30,90 1,70 44 D A B C R 0,25 0,13 R 0,50 0,13 (100 2) 0 0,2 0,79 ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 7 4.3 Material and finish Cable outlet: Class A : Aluminium/black anodised Class N : Aluminium/electroless nickel plated Class W
26、: Aluminium/olive drab cadmium plated Spacer pad: See EN 3660-036. 4.4 Assembly torque These torque values are intended for installation use only. See Table 3. Table 3 Shell size Torque Nm 0,5 09 7,80 11 10,60 13 15,20 15 16,30 17 16,30 19 16,30 21 19,10 23 19,10 25 19,10 4.5 Tests according to EN 2
27、591-100 Test details to be in accordance with Table 4, EN 3660-001 and EN 2591-100. Qualification to be in accordance with EN 3660-001. ? BS EN 3660-017:2009 EN 3660-017:2009 (E) 8 Table 4 EN 2591-Designation of the test Not applicable Applicable see EN 3660-001 Details 101Visual examination X 102 E
28、xamination of dimensions and mass X See 4.1. 205 Housing (shell) electrical continuity X Only class N and W and only if with grounding lug option: 5 m? 212 Surface transfer impedance (from 100 MHz to 1 GHz) a X 301 Endurance at temperature X According to class Only self-locking version and specify.
29、305 Rapid change of temperature X 306 Mould growth X See EN 3660-001. 307 Salt mist X Cable outlet not fitted to a connector and suspended with non metallic cord. Duration: Classes A and N 48 h Class W 500 h 308 Sand and dust X 314 Immersion at low air pressure X 315 Fluid resistance X Only self-loc
30、king versions and with spacer pad. 316 Ozone resistance X With spacer pad only 317 Flammability X With spacer pad only 318 Fire-resistance X 402 Shock X Method A. Severity: 100 g 403 Sinusoidal and random vibration X Method B. Level J. 406 Mechanical endurance X 10 cycles 408 Mating and unmating for
31、ces X continued BS EN 3660-017:2009 EN 3660-017:2009 (E) 9 Table 4 (concluded) EN 2591-Designation of the test Not applicable Applicable see EN 3660-001 Details 420 Mechanical strength of rear accessories X Shell sizeTorque N 09 11 13 15 17 19 21 23 25 108 108 108 217 217 217 326 326 435 422 Locking
32、 wire hole strength X 513 Magnetic permeability X Not fitted to a connector. Max values: Classes A, N and W 2,0 a 1 GHz to 10 GHz under consideration. 5 Designation EXAMPLE 1 Description block CABLE OUTLET Identity block EN3660-017XXXXX Number of this standard Material/Finish class (See 4.3) Couplin
33、g nut 1 without self-locking device 2 with self-locking device Strain relief type A without spacer pad and ground lug B with spacer pad and ground lug C with spacer pad and without ground lug D without spacer pad and with ground lug Shell size EXAMPLE 2 EN3660-017A1A09 Style A, cable outlet, alumini
34、um, black anodised plating, without self-locking, without spacer pad and ground lug, shell size 09. NOTE 1 No gaps are required between sections in the part number when printed. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. BS EN 3660-017:200
35、9 EN 3660-017:2009 (E) 10 6 Marking According to EN 2424, category P. 7 Technical specification Refer to EN 3660-001. BS EN 3660-017:2009 This page has been intentionally left blank ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?