《BS EN 13300-2001 Paints and varnishes. Water-borne coating materials and coating systems for interior walls and ceilings. Classification.pdf》由会员分享，可在线阅读，更多相关《BS EN 13300-2001 Paints and varnishes. Water-borne coating materials and coating systems for interior walls and ceilings. Classification.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13300:2001 Paints and varnishes Water-borne coating materials and coating systems for interior walls and ceilings Classification The European Standard EN 13300:2001 has the status of a British Standard ICS 87.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIG
2、HT LAW Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13300:2001 This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards C
3、ommittee and comes into effect on 15 June 2001 BSI 06-2001 ISBN 0 580 37649 4 National foreword This British Standard is the official English language version of EN 13300:2001. The UK participation in its preparation was entrusted to Technical Committee STI/ 28, Paint systems for non-metallic substr
4、ates, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catal
5、ogue under the section entitled “ International Standards Correspondence Index” , or by using the “ Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for thei
6、r correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interes
7、ts informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this docume
8、nt indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13300 April 2001 ICS 87.040 Englis
9、h version Paints and varnishes - Water-borne coating materials and coating systems for interior walls and ceilings - Classification Peintures et vernis - Produits de peinture et systmes de peinture en phase aqueuse pour murs et plafonds intrieurs - Classification Beschichtungsstoffe - Wasserhaltige
10、Beschichtungsstoffe und Beschichtungssysteme fr Wnde und Decken im Innenbereich - Einteilung This European Standard was approved by CEN on 19 February 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the
11、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A
12、 version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, F
13、rance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001
14、CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13300:2001 E Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 13300 : 2001 Contents Page Foreword . . . . . . . . .
15、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Scope. .
16、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 Normative references. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Terms
17、and definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 General classification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 Additio
18、nal classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Annex A (informative) Other criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Foreword T
19、his European Standard has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2
20、001, and conflicting national standards shall be withdrawn at the latest by October 2001. Annex A is informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech
21、Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction The names used today to describe coating materials and coating systems pay little regard to technical, functional a
22、nd end use categories. This makes it difficult to devise an unequivocal simple terminology applicable to all product types. This European Standard attempts to address this problem by separately defining categories of appearance and end use, but with no assumptions as to whether or not a given produc
23、t, by its appearance alone, will be suitable for a particular use. The objective is to avoid misuse of coating systems by the misunderstanding or over-statement of performance claims. The possibilities for future technical advances are recognized. The treatment of interior surfaces has aesthetic and
24、/or protective functions. The results of such treatments include the following: decoration of surfaces by changing or restoring their appearance; protection of the substrate against aesthetic and/or functional deterioration. This European Standard identifies criteria that need to be considered when
25、assessing the suitability of a coating system for a particular end use and provides a framework for communicating this information between manufacturer and user. This should assist in the removal of technical barriers to trade. It is in the responsibility of the manufacturer of a coating system to d
26、esignate the appropriate categories for end use and appearance. 1 Scope This European Standard specifies a general system for the classification of water-borne coating materials and coating systems for the decoration and protection of interior walls and ceilings comprised of new and old, coated and
27、uncoated surfaces. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent ame
28、ndments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the last edition of the publication referred to applies (including amendments). Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05
29、:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ? Page 3 EN 13300 : 2001 EN 971-11996Paints and varnishes Terms and definitions for coating materials Part 1: General terms EN 1062-11996Paints and varnishes Coating materials and coating systems for exterior masonry and concrete Part 1: Classificati
30、on EN 21524Paints and varnishes Determination of fineness of grind (ISO 1524:1983) EN ISO 787-18General methods of test for pigments and extenders Part 18: Determination of residue on sieve; Mechanical flushing procedure (ISO 787-18:1983) EN ISO 2813Paints and varnishes Determination of specular glo
31、ss of non-metallic paint films at 20, 60 and 85 (ISO 2813:1994, including Technical Corrigendum 1:1997) ISO 787-7General methods of test for pigments and extenders Part 7: Determination of residue on sieve; Water method; Manual procedure ISO 6504-3Paints and varnishes Determination of hiding power P
32、art 3: Determination of contrast ratio (opacity) of light-coloured paints at a fixed spreading rate ISO 11998Paints and varnishes Determination of wet-scrub resistance and cleanability of coatings 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions
33、 apply. 3.1 coating material product, in liquid or in paste or in powder form, that when applied to a substrate forms a film possessing protective, decorative and/or other specific properties EN 971-1 : 1996 3.2 coating system total sum of the coats of coating materials which are to be applied or wh
34、ich have been applied to a substrate EN 971-1 : 1996 3.3 coating system for interior surfaces coating system for the treatment of interior walls and ceilings 3.4 water-borne coating material coating material, the binder of which is dispersed, dissolved or diluted in water 3.5 decoration treatments w
35、ith the primary objective to change or restore the appearance of the substrate. Functions of these treatments are colour, gloss and texture. They can also include protective functions. EN 1062-1 : 1996 3.6 protection treatments with the primary objective to impart resistance to soiling, cleaning, fi
36、re, moisture, and biological, mechanical or chemical attacks. These treatments will also include decorative functions. 4 General classification Coating materials and coating systems for interior walls and ceilings shall be classified as specified in 4.1 and 4.2. 4.1 Classification by end use Classif
37、ication by end use shall be as follows: a) decoration; b) special properties. 4.2 Classification by chemical type of binder Classification by chemical type of binder shall be derived from that component of the binder which is decisive for the characteristic properties of the final coating system. Th
38、e chemical type of the binder shall be given using, for example, the following terms: hydraulic lime, cement, silicate; acrylic resin, vinyl resin, alkyd resin, epoxy resin, copolymers. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ? Page
39、4 EN 13300 : 2001 NOTE 1 This list of terms is not exhaustive to allow additional binders to be described as coating technology advances. NOTE 2 The quality of an indoor coating material is not dependent solely on the binder types used. The amount of binder(s) and/or other constituents may be of gre
40、ater importance. 5 Additional classification Coating materials and coating systems for interior walls and ceilings may additionally be classified as specified in 5.2 to 5.5. 5.1 Introduction Additional properties and characteristics of coating systems for interior walls and ceilings are classified i
41、n 5.2 to 5.5. The coating systems are assessed independently of the substrate to which the material is intended to be applied. Properties such as adhesion and texture that are dependent on the substrate have, therefore, not been included, Nevertheless, it is essential that the coating system adheres
42、 properly to its appropriately prepared substrate. It needs to maintain adhesion under normal conditions during its specified lifetime. Where applicable, the characteristics of the complete coating system, including method(s) of application, colour and opacity, should preferably be agreed between su
43、pplier, specifier, applicator and customer. Requirements for substrate preparation shall also be specified and observed. Coating thickness and texture are subject to the manufacturers recommendations and are affected by the method of application, the properties of the substrate and the formulation.
44、These factors affect many important properties of the coating system such as soiling resistance and general appearance. To achieve an effective coating system, specifiers and users shall take note of recommendations for application regarding the use of the coating materials and special sealers and/o
45、r primers. Care shall be taken to apply the material(s) under suitable temperature and humidity conditions and to observe recommended drying times and overcoating intervals. The coating shall be recoatable at least by the same coating material. Full information should be provided in suppliers data s
46、heets. The classes defined in this standard are not intended to represent a quality scale. 5.2 Gloss Classsification by gloss shall be based on specular-gloss values at 60 or 85 when tested by the method described in EN ISO 2813, as shown in table 1. Table 1 - Classification by specular gloss Design
47、ationAngle of incidenceReflectance Gloss60 60 Mid sheen*)60 85 60 10 Matt85 10 Dead-matt85 5 *) See note 4. If the reflectance measured at 60 is below 10, the measurement shall be repeated at 85. The value obtained at 85 determines the classification. NOTE 1 In practice, the gloss level achieved wil
48、l depend on the state and nature of the substrate. NOTE 2 In the case where reflectance is below 5 at 85, the term dead-matt can be used. NOTE 3 Gloss cannot be measured on textured surfaces of coatings of coarse and very coarse granularity. NOTE 4 According the national preference, the designation
49、of “mid sheen“ can vary: e.g. semi-gloss, semi-matt, satin. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:39:10 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ? Page 5 EN 13300 : 2001 5.3 Largest grain size (granularity) Classification by largest grain size shall be based on the size of the largest particles present in a significant amount to influence the texture of the coating system, by the following categories: a) fine:up to 100 m, determined in accordance with EN 21524;