《BS EN 4640-001-2009 Aerospace series — Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve.pdf》由会员分享，可在线阅读，更多相关《BS EN 4640-001-2009 Aerospace series — Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve.pdf（26页珍藏版）》请在三一文库上搜索。
1、? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? BS EN 4640-001:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4640-001 February 2009 ICS 49.060 English Version Aerospace series - Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, w
2、ith removable alignment sleeve holder - Part 001: Technical specification Srie arospatiale - Connecteurs, optiques, rectangulaires, contacts multiples, rackables, frule diamtre 1,25, quips dun porte sleeve dmontable - Partie 001: Spcification technique Luft- und Raumfahrt - Optischer Rechtecksteckve
3、rbinder, Gehuse, Einschub, Steckverbinder, Multipin, Ferrulendurchmesser 1,25 mm, demontierbarer Zentrierhlsenhalter - Teil 001: Technische Lieferbedingungen This European Standard was approved by CEN on 11 July 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which st
4、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standa
5、rd exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national stan
6、dards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Ki
7、ngdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4640-001:2009: E B
8、S EN 4640-001:2009 EN 4640-001:2009 (E) 2 Contents Page Foreword 3? Introduction .4? 1?Scope 4? 2?Normative references 4? 3?Terms and definitions .5? 4?Description .5? 5?Design .6? 6?Definition drawings6? 7?Tests . 16? 8?Quality assurance . 19? 9?Designation and marking . 23? ? BS EN 4640-001:2009 E
9、N 4640-001:2009 (E) 3 Foreword This document (EN 4640-001:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approva
10、l of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflict
11、ing national standards shall be withdrawn at the latest by August 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to t
12、he CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithua
13、nia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. ? BS EN 4640-001:2009 EN 4640-001:2009 (E) 4 Introduction This family of fibre optic connectors is derived from ARINC Specification 600 connectors. It is sui
14、table for use on aerospace onboard applications. It provides easy access for optical contact end face cleaning. The optical contacts are capable of accepting single cable sizes up to a maximum of 2 mm outside diameter. 1 Scope This standard specifies the general characteristics, the conditions for q
15、ualification, acceptance and quality assurance, as well as the test programs and groups for rectangular multipin fibre optic connectors. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited appl
16、ies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3197, Aerospace series Installation of aircraft electrical and optical interco
17、nnection systems 1 EN 3909, Aerospace series Test fluids and test methods for electric components and sub-assemblies EN 4639-101, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 mm diameter ferrule, with removable alignment sleeve holder Part 101: Optical contact for c
18、able EN 4641-100 Operating temperatures between 65 C and 125 C Product standard EN 4640-002, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 002: Specification of performance and contact arrangements
19、EN 4640-003, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 003: Plug optical connector Product standard EN 4640-004, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact,
20、1,25 diameter ferrule, with removable alignment sleeve holder Part 004: Receptacle optical connector Product standard EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts ARINC Specification 600, Air Transport Avionics Equipment Interfaces 2 MIL-I
21、-81969/14, Installing and removal tools, connector electrical contact, type III, class 2, composition B3 * And all parts quoted in this standard. 1 Published as ASD Prestandard at the date of publication of this standard. 2 Published by: AERONAUTICAL RADIO, INC. 2551 Riva road, Annapolis, Maryland 2
22、1401-7435 USA. 3 Published by: Department of Defence (DOD), the Pentagon, Washington, D.C. 20301 USA. ? BS EN 4640-001:2009 EN 4640-001:2009 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Description 4.1 General This document
23、describes an optical connector insert to be installed in plug and receptacle housings. Plug and receptacle housings conform to ARINC Specification 600. The precise alignment of the optical contacts is accomplished by alignment sleeves held in a removable sleeve holder. The plug connector contain mal
24、e insert as specified in EN 4640-003. The receptacles connector contain female insert as specified in EN 4640-004. The female insert is composed of an insert and a removable sleeve holder as specified in EN 4640-004. The sleeve holder is delivered with the female insert. It is considered as a part o
25、f the female insert (specific design per manufacturer). The sleeve holder can be supplied separately only for repair purpose. The optical contact is in accordance with EN 4639-101. The connectors are keyed as specified in ARINC Specification 600. Connector type designation as specified in ARINC Spec
26、ification 600. 4.2 Receptacle Receptacle description as specified in ARINC Specification 600. 4.3 Plug Plug description as specified in ARINC Specification 600. 4.4 Materials and surface treatment 4.4.1 General When dissimilar metals are in close contact, adequate protection against corrosion shall
27、be used for the electromotive force of the cell not to exceed 0,25 V (see EN 3197). 4.4.2 Housings The connector housing description as specified in ARINC Specification 600. ? BS EN 4640-001:2009 EN 4640-001:2009 (E) 6 4.4.3 Optical contacts and alignment sleeves The contacts shall be of suitable ma
28、terials as specified in EN 4639-101. The optical alignment sleeves shall be of suitable materials as specified in EN 4640-002. The optical contacts are sprung-loaded. The spring force is defined in the product standard (EN 4639-101). 4.4.4 Metallic or non-metallic materials The materials used for in
29、serts, seals and grommets shall have a hardness and mechanical characteristics consistent with the required use. 5 Design 5.1 Housing The connector housing design as specified in ARINC Specification 600. 5.2 Connector inserts The connector insert carrying the optical contacts shall be in hard materi
30、al and have a cross section and radii such that no cracks, flaking or breaks can occur in normal operation. The mechanical contacts retention system shall be integrated in the connector insert. Sealing of the rear face of the connector insert can be provided by a grommet adapted to the external diam
31、eter of the cable. The design shall permit individual installation of the contacts without removal of the connector insert. Fitting and removal of the contacts shall be from the rear. For ease of operation, tools as per MIL-I-81969/14-03 (P/N for size 16) may be used. Contact position identification
32、 shall be permanent and contrasted on the rear face of the insert or grommet. 6 Definition drawings 6.1 General The general dimensions and the masses of receptacles, plugs and protective covers are given in the product standards. 6.2 Receptacle All housing dimensions are defined in ARINC Specificati
33、on 600. 6.3 Plug All housing dimensions are defined in ARINC Specification 600. ? BS EN 4640-001:2009 EN 4640-001:2009 (E) 7 6.4 Connector inserts 6.4.1 Connector interface insert See Figure 1. Key 1 Receptacle connector 5 Mechanical bottom of receptacle 2 Mechanical bottom of plug 6 Plug connector
34、3 Front face of the insert 7 Pin cavity position A 4 Sleeve holder Figure 1 6.5 Mating dimensions The mating dimensions receptacle (free position) are shown in Figure 2. ? BS EN 4640-001:2009 EN 4640-001:2009 (E) 8 Sleeve-holder screw cavity (Sleeve-holder not show) Optical contact position Key 1 Li
35、mit stop of the alignment sleeve holder screw 2 (unmated position) 3 Mechanical bottom of the receptacle NOTE Other dimensions in accordance with ARINC Specification 600. Figure 2 BS EN 4640-001:2009 EN 4640-001:2009 (E) 9 The mating dimensions of plug (free position) are shown in Figure 3. Key 1 (u
36、nmated position) 2 Mechanical bottom of the plug NOTE Other dimensions in accordance with ARINC Specification 600. Figure 3 6.5.1 Receptacle with female insert and plug with male insert The displacement of the optical contact in the connector is shown in Figure 4. Dimensions and tolerances are in mi
37、llimetres. Mating position Key 1 Mechanical bottom 2 Receptacle connector 3 Plug connector Figure 4 1 2 min. 7,01 5,92 1 2 3 BS EN 4640-001:2009 EN 4640-001:2009 (E) 10 6.5.2 Receptacle connector Contact entering mating sleeve holderContact optically mated Key 1 # 22 Electrical contact 6 Bloc side 2
38、 Sleeve holder 7 Rack side 3 # 12 Electrical contact 8 Plug 4 # 16 Electrical contact 9 Optical contact 5 Receptacle X1 contact entering mating sleeve holder X2 contact optically mated Optical contact 18,68 mm .735 16,53 mm .650 # 22 16,30 mm .642 b 13,89 mm .547 # 22 20,32 mm .800 a 18,99 mm .748 O
39、ptical contact 16,25 mm .634 13,28 mm .523 # 20 20,54 mm .809 a 18,82 mm .741 # 20 16,48 mm .649 b 14,04 mm .553 # 16 25,70 mm 1.012 a 24,10 mm .949 # 16 18,42 mm .725 b 20,77 mm .818 # 12 25,60 mm 1.008 a 24,20 mm .953 # 12 19,60 mm .772 b 17,57 mm .692 a Values for # 22, # 20, # 16, # 12 electrica
40、l contacts are for contact entering mating insulator extracted from ARINC Specification 600. These values are given for information only. Refer to ARINC Specification 600 for more information. b Values for # 22, # 20, # 16, # 12 electrical contacts are for contact electrically engaged extracted from
41、 ARINC Specification 600. These values are given for information only. Refer to ARINC Specification 600 for more information. Figure 5 1 1 2 2 3 3 4 4 5 5 6 7 7 6 8 9 8 9 BS EN 4640-001:2009 EN 4640-001:2009 (E) 11 6.5.3 Coupling contact condition Key 1D2 - Sleeve cavity inner diameter 2 Sleeve to s
42、leeve-holder cavity stop 3 Optical contact to sleeve-holder stop Condition: in every case, J 0 The different shapes and dimensions of the sleeve cavity must be defined to warranty this condition. Figure 6 6.5.4 Contact arrangements Identification of the contact position shall be permanently marked i
43、n contrasting colour on the rear face of the module. Contact arrangements 20F12Q8 for shell size 2 or 3: see Figure 7. BS EN 4640-001:2009 EN 4640-001:2009 (E) 12 Receptacle rear face Plug rear face Plug front face Key 1 Ref on ribs 2 Sleeve-holder screw hole (on receptacle side) 3 12 optical caviti
44、es 4 End of the optical contacts 5 Keyway 6 8 cavities for # 8 quadrax contacts Contact body is grounded to the connector shell 7 Angular position of the optical contact polarization key 8 Step Number of contacts Contact size Insert cavity location 12 Optical contact RR/RR 1 thru 12 8 8 (Quadrax) FR
45、/FR (Receptacle side) RR/RR (Plug side) AA thru HH NOTE RR/RR = Contacts are REAR RELEASE / REAR REMOVABLE FR/FR = Contacts are FRONT RELEASE / FRONT REMOVABLE Figure 7 Receptacle front face (without sleeve holder) BS EN 4640-001:2009 EN 4640-001:2009 (E) 13 Contact arrangements 36F36 for shell size 2 or 3: see Figure 8. Receptacle rear face Plug rear face Plug front face Key 1 Ref on ribs 2 3 cavities for sleeve-holder screw (on receptacle side) 3 Keyway 4 36 optical cavities 5 End of the optical contacts 6 Angular position of the optical contact polarization key Number of contacts Co