《BS EN 764-3-2002 PRESSURE EQUIPMENT PART 3 DEFINITION OF PARTIES INVOLVED1.pdf》由会员分享，可在线阅读，更多相关《BS EN 764-3-2002 PRESSURE EQUIPMENT PART 3 DEFINITION OF PARTIES INVOLVED1.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 764-3:2002 Pressure equipment Part 3: Definition of parties involved The European Standard EN 764-3:2002 has the status of a British Standard ICS 01.040.23; 23.020.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 764-3:2002 This British Standard,
2、 having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 13 June 2002 BSI 13 June 2002 ISBN 0 580 39864 1 National foreword This British Standard is the official English lang
3、uage version of EN 764-3:2002. The UK participation in its preparation was entrusted to Technical Committee PVE/1, Pressure vessels, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standa
4、rds which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This
5、publication does not purport to include all the necessary provisions of a contract. Users of this publication are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to
6、the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside
7、front cover, the EN title page, pages 2 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 764-3 May 2002 ICS 01.040.23; 2
8、3.020.30 English version Pressure equipment - Part 3: Definition of parties involved Equipements sous pression - Partie 3: Dfinition des parties impliques Druckgerte - Teil 3: Definition der beteiligten Parteien This European Standard was approved by CEN on 29 April 2002. CEN members are bound to co
9、mply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Managemen
10、t Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the offic
11、ial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION
12、 COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 764-3:2002 E EN 764-3:2002 (E) 2 Contents page Foreword3 1Sco
13、pe 4 2Terms and definitions4 EN 764-3:2002 (E) 3 Foreword This document EN 764-3:2002 has been prepared by Technical Committee CEN/TC 54 “Unfired pressure vessels“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication
14、 of an identical text or by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latest by November 2002. This document has been prepared under a mandate given to CEN by the European Commission (EC) and the European Free Trade Association This Eur
15、opean Standard consists of seven parts which are: Part 1Definitions of pressure, temperature and volume; Part 2Quantities, symbols and units; Part 3Definition of parties involved; Part 4Establishment of technical delivery conditions for metallic materials; Part 5Inspection documentation of metallic
16、materials and compliance with the material specification; Part 6Operating instructions; Part 7Safety systems for unfired pressure equipment. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standar
17、d: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN 764-3:2002 (E) 4 1 Scope This European Standard defines terms and definitions of parties in
18、volved in the design, manufacture, testing and inspection of pressure equipment and assemblies addressed by the European Directive 97/23/EC. 2 Terms and definitions 2.1 material manufacturer individual or organisation that produces material in the basic product forms used in the manufacture of press
19、ure equipment 2.2 material supplier individual or organisation, that may or may not be the material manufacturer, who supplies material or parts used in the manufacture of pressure equipment and assemblies 2.3 manufacturer individual or organisation that is responsible for the design, fabrication, t
20、esting, inspection, installation of pressure equipment and assemblies where relevant NOTE 1The manufacturer can subcontract one or more of the above mentioned tasks under its responsibility. NOTE 2In EU member states the manufacturer is responsible for compliance with the Pressure Equipment Directiv
21、e 97/23/EC. For those manufacturers outside of the EU their authorized representative inside the EU assumes this responsibility. 2.4 designer, fabricator and/or installer, subcontractor of the manufacturer individual or organisation that respectively performs design, fabrication, testing, installati
22、on where relevant, of pressure equipment under contract to the manufacturer 2.5 first party individual or organisation that designs, manufactures or supplies the pressure equipment or the assembly 2.6 second party individual or organisation that uses and/or operates the pressure equipment or the ass
23、embly 2.7 third party individual or organisation independent of the first and second party NOTEInspectors of the suppliers of material, manufacturers, fabricators/installers or their subcontractors are not third party inspectors. 2.8 user and/or operator individual or organisation that uses and/or o
24、perates pressure equipment or assemblies 2.9 purchaser individual or organisation that buys pressure equipment, assemblies or pressure parts on behalf of the user and/or operator or for its own use EN 764-3:2002 (E) 5 2.10 inspector individual who is independent from production responsible for carry
25、ing out inspections to verify that the requirements of the technical specification(s) are met 2.11 responsible authority competent organisation which is independent of the manufacturer. For application within the jurisdiction of the European Union this organisation may be a notified body, a recognis
26、ed third-party organisation or an user inspectorate. For application outside the jurisdiction of the European Union this organisation may be a government regulating body or an independent inspection authority. For the purpose of this standard all these organisations have been collectively termed res
27、ponsible authority (RA) 2.12 notified body organisation according to the Article 12 of the Pressure Equipment Directive 97/23/EC NOTEThe names and tasks of the notified bodies are published in the Official Journal of the European Communities. 2.13 recognized third-party organization organisation acc
28、ording to the Article 13 of the Pressure Equipment Directive 97/23/EC NOTEThe names and tasks of the recognised third-party organisations are published in the Official Journal of the European Communities. 2.14 user inspectorate organisation according to the Article 14 of the Pressure Equipment Direc
29、tive 97/23/EC A user inspectorate acts exclusively for the group of which it is part. The names and tasks of the user inspectorate are not published in the Official Journal of the European Communities. The designation of an user inspectorate is optional for the Member States. BS EN 764-3:2002 BSI 38
30、9 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are u
31、pdated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Brit
32、ish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically
33、 receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:
34、/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internationa
35、l standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscr
36、ibing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information
37、 regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publication
38、s of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission
39、 from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.