《07-30150187-DC.pdf》由会员分享，可在线阅读，更多相关《07-30150187-DC.pdf（51页珍藏版）》请在三一文库上搜索。
1、a Date: 16 August 2007 Origin: International Latest date for receipt of comments: 30 November 2007 Project no.: 2006/01284 Responsible committee: PSE/17/-/4 Drilling and production equipment for petroleum and natural gas industries Interested committees: PSE/17 Title: Draft ISO 17078-3 Petroleum and
2、 natural gas industries - Drilling and production equipment Part 3: Running, pulling, and kick-over tools and latches for side-pocket mandrels Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you a
3、re aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 November 2007. This draft is issued to allow comments from interest
4、ed parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent A
5、ct 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or emai
6、l ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organizations
7、 represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site
8、http:/www.bsi-. Direct tel: 020 8996 7445 Responsible Committee Secretary: K Seyde (BSI) E-mail: keith.seydebsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 07/30150187 DC Licensed Copy: Lond
9、on South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are invited and will assist in the pre
10、paration of the consequent standard. Comments submitted will be reviewed by the relevant BSI committee before sending the consensus UK vote and comments to the international secretariat, which will then decide appropriate action on the draft and the comments received. If no comments are received to
11、the contrary, then the UK will approve this draft. If the international standard is approved, it is possible the text will be published as an identical British Standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submis
12、sion The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secret
13、ary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. Al
14、l comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x
15、 Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Def
16、inition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Mic
17、rosoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT
18、 IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE
19、 LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL S
20、TANDARD ISO/DIS 17078-3 International Organization for Standardization, 2007 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 67/SC 4 Voting begins on: 2007-08-16 Secretariat: ANSI Voting terminates on: 2008-01-16 Petroleum and natural gas industries
21、 Drilling and production equipment Part 3: Running, pulling and kick-over tools, and latches for side-pocket mandrels Industries du ptrole et du gaz naturel quipement de forage et de production Partie 3: Outils de mise en place, de dpose, de dviation et de verrouillage pour raccords poche latrale IC
22、S 75.180.10 ISO/CEN PARALLEL ENQUIRY The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject of interest to European standardization. In accordance with the ISO-lead mode of collaboration as defined in the Vienna Agreement, consultation on this ISO/DIS has
23、the same effect for CEN members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS vote in ISO and formal vote in CEN. In accordance with the provisions of Co
24、uncil Resolution 15/1993 this document is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, ce document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat
25、. ISO Central Secretariat work of editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de l
26、ISO au stade de publication. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 17078-3 ii ISO 2007 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe
27、s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy.
28、The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care
29、has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-prote
30、cted by ISO. Except as permitted under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permissi
31、on being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.o
32、rg Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 17078-3 ISO 2007 All rights reserved iii Content
33、s Page Foreword.iv Introductionv 1 Scope.1 2 Normative references .1 3 Terms and definitions.2 4 Symbols and abbreviated terms6 5 Functional specification.6 5.1 General 6 5.2 Functional characteristics6 5.3 Well parameters8 5.4 Operational parameters9 5.5 Environmental service grades (class designat
34、ion)9 5.6 Design validation grades9 5.7 Product functional testing grades.9 5.8 Quality control grades9 5.9 Additional testing10 6 Technical specification.10 6.1 General requirements.10 6.2 Technical characteristics .10 6.3 Design criteria.10 6.4 Allowable design changes .14 6.5 Design verification
35、and validation requirements15 6.6 Product functional testing requirements 15 7 Supplier/manufacturer requirements 16 7.1 General 16 7.2 Documentation and data control .16 7.3 Product identification requirements18 7.4 Quality control requirements.18 7.5 Heat treatment requirements .23 7.6 Welding req
36、uirements 23 7.7 Non-destructive examination (NDE) requirements.24 7.8 Storage and shipping preparation.24 7.9 Allowable changes after manufacturing .24 7.10 Reconditioning and repair of used running, pulling, and kick-over tools, and latches.25 Annex A (normative) Requirements for running and pulli
37、ng tools26 Annex B (normative) Requirements for kick-over tools29 Annex C (normative) Requirements for latches.33 Annex D (informative) Figures.38 Bibliography.43 Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
38、 ISO/DIS 17078-3 iv ISO 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each
39、member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
40、 Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards
41、adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of
42、patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 17078-3 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production
43、equipment ISO 17078 consists of the following parts, under the general title Petroleum and natural gas industries Down hole equipment: Part 1: Side-pocket mandrels Part 2: Flow control devices for side-pocket mandrels Part 3: Running, pulling, and kick-over tools, and latches for side-pocket mandrel
44、s Part 4: Practices for side-pocket mandrels and related equipment Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:23:29 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ISO/DIS 17078-3 ISO 2007 All rights reserved v Introduction This International Standard has bee
45、n developed by users/purchasers and suppliers/manufacturers of running tools, pulling tools, kick-over tools, and latches used for installation and retrieval of flow control and other devices in side-pocket mandrels that are intended for use in the worldwide petroleum and natural gas industry. This
46、International Standard is intended to provide requirements and information to all parties who are involved in the specification, selection, manufacture, testing, and use of these latches and related tools. Further, this International Standard addresses supplier/manufacturer requirements that set the
47、 minimum parameters with which they must comply, to claim conformity with this International Standard. This International Standard has been structured to support varying requirements in environmental service, design validation, product functional testing, and quality control grades. These variations
48、 allow the user/purchaser to select the necessary grade for a specific application. Environmental service classes. One environmental service class is provided for running tools, pulling tools, and kick-over tools, and four environmental service classes are provided for latches. This provides the use
49、r/purchaser with a range of choices to select latch products to meet varying environmental conditions. Design validation grades. Two design validation grades are provided for running, pulling, and kick-over tools, and latches. These provide the user/purchaser a range of technical and performance requirements. This will ensure that the products supplied according to this standard wil